Download
Share
Print this page
KTM 250 SX-F EU Setup Instructions
  1. Manuals
  2. Brands
  3. KTM Manuals
  4. Motorcycle
  5. 250 SX-F EU
  6. Setup instructions

KTM 250 SX-F EU Setup Instructions

Hide thumbs Also See for 250 SX-F EU:

Advertisement

Quick Links

Download this manual See also: Owenrs Manual, Owner's Manual
SETUP INSTRUCTIONS
2010
250 SX-F EU
250 SX-F USA
Art. no. 3211544en

Advertisement

loading

Related Manuals for KTM 250 SX-F EU

Summary of Contents for KTM 250 SX-F EU

  • Page 1 SETUP INSTRUCTIONS 2010 250 SX-F EU 250 SX-F USA Art. no. 3211544en...
  • Page 3 KTM accepts no liability for delivery options, deviations from illustrations and descriptions, as well as misprints and other errors.

  • Page 4: Means Of Representation

    MEANS OF REPRESENTATION Symbols used The symbols used are explained in the following. Identifies an expected reaction (e.g. of a work step or a function). Identifies an unexpected reaction (e.g. of a work step or a function). Identifies a page reference (more information is provided on the specified page). Formats used The typographical and other formats used are explained below.
  • Page 5 SET‑UP Unpacking and setting up the vehicle – Remove the box and the plastic packaging. Info An assistant prevents the motorcycle from falling over. To avoid damaging the motorcycle during assembly, leave the protective plastic on the vehicle until you have finished. –...
  • Page 6 Info Read the accompanying KTM PowerParts installation instructions. – Refuel. ( p. 6) – Position all controls exactly on the handlebar. Tighten all screws. – Print out the current PDI form found on KTM DEALER.NET and perform the delivery inspection.
  • Page 7 WORK Removing the seat – Remove screw . Lift up the seat at the rear, pull it back and then remove from  above. 500080-10 Mounting the seat – Hook in the front of the seat at the collar sleeve of the fuel tank, lower it at the rear and simultaneously push it forward.
  • Page 8 WORK Installing the front fender – Ensure that the spacers are mounted in the fender. – Position the front fender. Mount and tighten screws  Guideline Remaining screws, chassis 10 Nm (7.4 lbf ft) Info Make sure the holding lugs engage in the start number plate or headlight mask.
  • Page 9 WORK Warning Environmental hazard Improper handling of fuel is a danger to the environment. – Do not allow fuel to get into the ground water, the ground, or the sewage system. – Switch off engine. – Open the filler cap. ( p.

  • Page 10: Technical Data - Tightening Torques For Chassis

    TECHNICAL DATA - TIGHTENING TORQUES FOR CHASSIS – Spoke nipple, front wheel M4.5 5… 6 Nm (3.7… 4.4 lbf ft) – Spoke nipple, rear wheel 5… 6 Nm (3.7… 4.4 lbf ft) – Remaining nuts, chassis 15 Nm (11.1 lbf ft) –...
  • Page 11 SUBSTANCES Super unleaded (ROZ 95 / RON 95 / PON 91) According to – DIN EN 228 (ROZ 95 / RON 95 / PON 91)

  • Page 12: Auxiliary Substances

    AUXILIARY SUBSTANCES Long-life grease Guideline – ® KTM recommends Motorex products. Supplier ® Motorex – Fett 2000...
  • Page 13 *3211544en* 3211544en KTM-Sportmotorcycle AG 5230 Mattighofen/Austria http://www.ktm.com...

This manual is also suitable for:

250 sx-fusa