Gas Conversion; Burner Features - Samsung GN641FDXD1 Installation And User Manual

Gas Conversion

■ Be careful, the operations and adjustments to be carried out when converting
from one gas to another.
■ All work must be carried out by a qualified technician.
■ Before you begin, turn off the gas and electricity supply to the appliance.
1
Change the injector of the burners.
Remove the pan support, Burner lid and Flame spreader.
Unscrew the injector using a 7mm box spanner and replace it with
the stipulated injector for new gas supply. ( see table 1. Page 27.)
Carefully reassemble the all components.
After injectors are replaced, it is advisable to strongly tighten the
injector in place.
Injector
2
Adjusting of the taps of the cooking hob burners for
reduced consumption
➀ Turn the taps down to minimum.
➁ Remove the control handles from taps.
Control handle
➂ Adjusting the by-pass screw.
Tap
Sealing ring
Tap
by-pass screw
➃ Replace the control handles on the taps.
■ Do not dismantle the tap shaft : in the event of a malfunction, change the whole tap.
■ Before placing the burners back on the top place, make sure that the injector is
not blocked.
■ A full operational test and a test for possible leakages must be carried out after
gas conversion. (such as soap water or gas detector)
■ After completing conversion, a qualified technician or installer has to mark "V"
on the right gas category
to match with the setting
in rating plate.
Remove the previous
setting "V" mark.
- For converting G20 into G30 or G31, the screw must
be screwed down fully tight.
- At this stage, light up the burners and turn the
control handles from max position to minimum
position to check flame stability.
- For converting G30 or G31 into G20, please contact
"After-Sales Service".
ELECTRONICS
GN642JDXD1 S/N: V1PT79MC300001
G20/20mbar 220-240V 50/60Hz
∑Qn Q20:8.3kW G30:591g/h G31:570g/h
GB Cat.: ll 2H3+
G20-20mbar G30/29mbar G31/37mbar
26

Burner Features

Nominal heat input and flow rates see below at 15˚C at 1,013 mbar.
COUN- TYPE OF
TRY GAS
GB,IT
FR,HU
G-30
BE,LT
BUTANE
NL,PT
29 mbar
ES,CZ
SK
G-30
PL BUTANE
36 mbar
GB,IT
FR,BE G-31
LT,PT PROPANE
ES,CZ
37 mbar
SK
GB,IT
FR,BE G-20
LT,PT NATURAL
PL,ES
20 mbar
CZ,SK
G-20
HU NATURAL
25 mbar
0063
- Aeration adjustment none
BURNER Triple-Crown Rapid
POSITION Max Max
Min Min
Injector make
85
98
(1/100 mm)
Nominal heat input
0.75
3.8 2.7 3.0
(Kw)
Nominal flow rates
53
267 193 211
(L/h)
Injector make
93 80
(1/100 mm)
Nominal heat input
0.85
3.8 2.7 3.0
(Kw)
Nominal flow rates
259 185 58
203
(L/h)
Injector make
85
98
(1/100 mm)
Nominal heat input
2.5
3.8 3.0 0.7
(Kw)
Nominal flow rates
254
177 199 49
(L/h)
Injector make
135
119
(1/100 mm)
Nominal heat rating
3.8 1.4 3.0 0.78
(Kw)
Nominal flow rates
361 129 271 79
(L/h)
Injector make
128 110
(1/100 mm)
Nominal heat input
3.8 1.4 3.0 0.84
(Kw)
Nominal flow rates
350
129 271 79
(L/h)
Burner Calibrated orifice 1/100mm
Auxiliary
Semi-rapid
Rapid
Triple-Crown
27
(Table 1)
Semi-rapid Auxiliary
Total
Max Max
Min Min
65 50
-
1.75
0.43 1.0 0.37 11.3
25
120 31 71
62 47 -
1.75
0.48 1.0 0.38 11.3
125 25
33 71
65 50
-
1.75
0.4 1.0 0.33 11.3
118 28 68 23
97 72 -
1.75 0.51
1.0 0.29 11.3
54
166 91 30
91 68 -
1.75 0.57
1.0 0.32 11.3
54
166 91 30
31
34
45
65