Settings For The Speakers - Sony DAV-TZ210 Operating Instructions Manual
Hide thumbs
Also See for DAV-TZ210:
- Quick setup manual (2 pages) ,
- Operating instructions (2 pages) ,
- Operating instructions manual (72 pages)
Table of Contents
Advertisement
Settings for the speakers
[SPEAKER SETUP]
You can adjust the speaker settings manually
without performing the Quick Setup.
Select the speakers you will use, set the speaker
distance from your listening position, and then
adjust the sound level for each speaker. You can
adjust the sound level by using the [TEST
TONE] function.
x [CONNECTION]
[FRONT]
[YES]
[CENTER]
[YES]: Normally select this.
[NONE]: Select this if no center speaker is used.
[SURROUND]
[YES]: Normally select this.
[NONE]: Select this if no surround speakers are
used.
[SUBWOOFER]
[YES]
Note
• When you change the [CONNECTION] setting, the
[STANDARD] of [SPEAKER FORMATION]
setting remains the same, but the other settings of
[SPEAKER FORMATION] return to
[STANDARD].
x [DISTANCE]
Set the distance of all the speakers from the
listening position.
For the best possible surround sound, place all
speakers at the same distance from the listening
position. The distance can be between 1.0 to 7.0
meters* (3 to 23 ft) for the front speakers, and
0.0 to 7.0 meters** (0 to 23 ft) for the center
speaker and surround speakers.
If you cannot place the center speaker at the
same distance, you can move the center speaker
up to 1.6 meters closer to the listening position.
If you cannot place surround speakers at the
same distance, you can move the surround
speakers up to 5.0 meters (16 ft) closer to the
listening position.
[FRONT] 3.0 m/10 ft: Set the front speaker
distance.
[CENTER] 3.0 m/10 ft: Set the center speaker
distance (up to 1.6 meters (5 ft) closer to the
front speakers).
[SURROUND] 3.0 m/10 ft: Set the surround
speaker distance (up to 5.0 meters (16 ft) closer
to the front speakers).
* 0.9 to 6.9 meters for North American models.
** 0.0 to 6.9 meters for North American models.
x [LEVEL (FRONT)]
You can adjust the sound level of the front
speakers, center speaker, and subwoofer. You
can set the parameters from –6.0 dB to 0 dB for
[L/R], and from –6.0 dB to +6.0 dB for
[CENTER] and [SUBWOOFER]. Be sure to set
[TEST TONE] to [ON] for easy adjustment.
[L/R] 0.0 dB: Set the front speaker level.
[CENTER] 0.0 dB: Set the center speaker level.
[SUBWOOFER] +2.0 dB: Set the subwoofer
level.
x [LEVEL (SURROUND)]
You can adjust the sound level of the surround
speakers. You can set the parameter from –6.0
dB to +6.0 dB. Set [TEST TONE] to [ON] for
easy adjustment.
[L/R] 0.0 dB: Set the surround speaker level.
x [TEST TONE]
You can adjust the sound level of the speakers
by using the [TEST TONE] function.
[OFF]: The test tone is not emitted from the
speakers.
[ON]: The test tone is emitted from each speaker
in sequence while adjusting the level.
Adjust the sound level as follows.
1
Set the [TEST TONE] to [ON].
2
Press C/X/x/c repeatedly to select the
desired speaker and the level, then
press
.
3
Repeat Step 2.
4
Press C/X/x/c to set [TEST TONE] to
[OFF] after adjusting the speaker level.
Page 61
Hide quick links:
Advertisement
Table of Contents
