Download  Print this page


Basic Features
When Double (À, Œ) mode has
been set in PIP (Picture-in-Picture), the
Picture Size cannot be set.
After selecting Zoom1, Zoom2 or
Wide Fit:
1. Press the ► button to select
2. Press the ENTERE button.
3. Press the ▲ or ▼ button to move the picture up
or down.
4. Press the ENTERE button.
5. Press the ► button to select Reset.
6. Press the ENTERE button to reset the picture
to its default position.
After selecting Screen Fit in HDMI (1080i/1080p) or
Component (1080i/1080p) mode, you may need to
center the picture:
1. Press the ◄ or ► button to select Position.
2. Press the ENTERE button.
3. Press the ▲, ▼, ◄ or ► button to move the
4. Press the ENTERE button.
5. Press the ◄ or ► button to select Reset.
6. Press the ENTERE button.
HD (High Definition): 16:9 - 1080i/1080p (1920x1080),
720p (1280x720)
Settings can be adjusted and stored for each
external device you have connected to an input on
the TV.
Input Source
Component (480i, 480p)
Component (1080i, 1080p),
HDMI (720p, 1080i, 1080p)
■ Digital Noise Filter (Off / Low / Medium / High / Auto
/ Auto Visualization): If the broadcast signal received
by your TV is weak, you can activate the Digital Noise
Filter feature to reduce any static and ghosting that may
appear on the screen.
When the signal is weak, try other options until the
best picture is displayed.
Auto Visualization: When changing analog channels,
displays signal strength.
Only available for analog channels.
When bar is green, you are receiving the best
possible signal.
■ MPEG Noise Filter (Off / Low / Medium / High /
Auto): Reduces MPEG noise to provide improved
picture quality.
[BOOK-PC7000]Web Manual-Eng.indb 18
■ HDMI Black Level (Normal / Low): Selects the black
level on the screen to adjust the screen depth.
■ Film Mode (Off / Auto1 / Auto2 / Cinema Smooth):
Sets the TV to automatically sense and process film
signals from all sources and adjusts the picture for
optimum quality.
■ Motion Judder Canceller (Off / Standard / Smooth
/ Demo): Removes drag from fast scenes with a lot of
movement to provide a clearer picture.
■ Screen Burn Protection: To reduce the possibility of
screen burn, this unit is equipped with screen burn
prevention technology. The Time setting allows you to
program the time between movement of the picture in
Pixel Shift (Off / On): Using this function, you can
minutely move pixels on the PDP in horizontal or vertical
direction to minimize after-images on the screen.
Picture Size
16:9, Zoom1,
Zoom2, 4:3
16:9, 4:3, Wide Fit,
Auto Protection Time (10 min. / 20 min. / 40 min. /
Screen Fit
1 hour / Off): Set the time the screen remains idle with a
still image until the screen saver is activated. The Screen
Saver prevents the formation of ghost images on the
16:9, 4:3
Scrolling: This function removes after-images on the
screen by moving all the pixels on the PDP according
to a pattern. Use this function when there are remaining
after-images or symbols on the screen, especially when
you displayed a still image on the screen for a long time.
Side Gray (Light / Dark): When you watch TV with the
screen ratio set to 4:3, the screen is prevented from any
damage by adjusting the white balance on both extreme
left and right sides.
Available only in HDMI mode.
An 1080p 24Hz HDMI signal must be input to use
the Cinema Smooth function.
Available in TV, AV, COMPONENT (480i / 1080i)
and HDMI (480i / 1080i).
If Motion Judder Canceller is Demo, you can
compare the difference between on and off modes.
Optimum condition for pixel shift
Time (minute)
1~4 min
The Pixel Shift value may differ depending on the
TV size (inches) and mode.
This function is not available in the Screen Fit
The after-image removal function has to be
executed for a long time (approximately 1 hour)
to effectively remove after-images on the screen.
If the after-image is not removed after performing
the function, repeat the function again.
Press any key on the remote control to cancel this
4 min
2010-06-21 오전 10:31:44


Table of Contents

   Related Manuals for Samsung pn50c7000yfxza

Comments to this Manuals

Symbols: 0
Latest comments: