Fc 5078, Fc 0578, Fc 5088, Fc 0588 - Cards (Dedicated) - IBM iSeries 270 Service Manual

Sb2 and sb3 hardware
Table of Contents

Advertisement

16. Determine the location where you want to assign the resource and select Assign to for that location.
17. Wait for the Hardware Resource Concurrent Maintenance display to appear with the message
indicating power on complete.
18. After exchanging the failing item, go to Verify the repair.
Note: If you have exchanged a 2766 or 2787 Fibre Channel IOA, the IBM 2105 disk unit subsystem
must be updated to use the World-Wide Port-Name of the new 2766 or 2787 IOA. This name can be
found in the Port worldwide name field on the iSeries by displaying detail on the 2766 or 2787 IOA
Logical Hardware Resource information in Hardware Service Manager in SST or DST.
The 16-digit World-Wide Port-Name can also be determined by appending the digits "1000" to the
beginning of the 12-digit IEEE Address found on the tailstock label of the Fibre Channel IOA. Use the
ESS Web Interface User's Guide (SC26-7346) to update the World-Wide Port-Name in the host
configuration on the IBM 2105 ESS. The ESS Web Interface User's Guide can also be found at the
following URL: http://ssddom02.storage.ibm.com/disk/ess/documentation.html
This ends the procedure.

FC 5078, FC 0578, FC 5088, FC 0588 - Cards (dedicated)

For use by authorized service providers.
Use this procedure to remove or replace cards (dedicated) in the FC 5078, FC 0578, FC 5088, or FC
0588.
In some cases, you do not need to power down the system to change PCI cards in an FC 5078, FC 0578,
FC 5088, FC 0588. Use the guidelines in FC 5078, FC 0578, FC 5088, FC 0588 - Cards (concurrent) to
determine if you should use dedicated or concurrent remove and replace procedures.
CAUTION:
The circuit card contains lead solder. To avoid the release of lead (Pb) into the environment, do not
burn. Discard the circuit card as instructed by local regulations. (RSFTC234)
Attention: All cards are sensitive to electrostatic discharge. See Work with electrostatic
discharge-sensitive parts.
To remove or replace cards (dedicated):
1. Power off the PCI expansion unit. See Expansion unit power procedure.
2. Disconnect the two ac power cords from the AC box.
3. Remove the rear cover. See FC 5078, FC 0578, FC 5088, FC 0588 - Covers.
4. Remove the EMC access plate over the card enclosure by loosening the thumb screws and pulling it
towards you.
5. Remove the retaining screws from the card enclosure.
6. Disconnect and label the cables that are attached to the back of the card enclosure.
7. Slide the card enclosure partially out of the frame.
8. Disconnect and label any cables from the card that you wish to remove.
9. Turn the latch counter-clockwise and lift up on the black latch to release the card.
Note: If you are removing an FC 2890 or 2892 IXS, then there are two latches that you will have to
turn and release.
10. Remove the card by gently pulling it out.
11. Install the new card by reversing the procedure. After exchanging the failing item, go to Verify the
repair.
Note: If you have exchanged a 2766 or 2787 Fibre Channel IOA, the IBM 2105 disk unit subsystem
must be updated to use the World-Wide Port-Name of the new 2766 or 2787 IOA. This name can be
found in the Port worldwide name field on the iSeries by displaying detail on the 2766 or 2787 IOA
Logical Hardware Resource information in Hardware Service Manager in SST/DST.
Analyze hardware problems
167

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents