Download  Print this page

Troubleshooting And Support; Troubleshooting - Philips 32PHH4509 User Manual

Hide thumbs

Advertisement

22
Troubleshooting and
support
22.1

Troubleshooting

Channels
No digital channels found during the installation
See the technical specifications to make sure that your TV
supports DVB-T or DVB-C in your country.
Make sure that all cables are properly connected and that the
correct network is selected.
Previously installed channels are not in the channel list
Make sure that the correct channel list is selected.
General
The TV does not switch on
• Disconnect the power cable from the power outlet. Wait for
one minute then reconnect it.
• Make sure that the power cable is securely connected.
Creaking sound at startup or switch off
When you are turning the TV on, off or to standby, you hear a
creaking sound from the TV chassis. The creaking sound is due
to the normal expansion and contraction of the TV as it cools
and warms up. This does not affect performance.
TV does not respond to the remote control
The TV requires some time to start up. During this time, the TV
does not respond to the remote control or TV controls. This is
normal behaviour.
If the TV continues to be unresponsive to the remote control,
you can check if the remote control is working by means of a
mobile phone camera. Put the phone in camera mode and point
the remote control to the camera lens. If you press any key on
the remote control and you notice the infra red LED flicker
through the camera, the remote control is working. The TV
needs to be checked.
If you do not notice the flickering, the remote control might be
broken or its batteries are low.
This method of checking the remote control is not possible with
remote controls which are wirelessly paired with the TV.
The TV goes back to standby after showing the Philips startup
screen
When the TV is in standby, a Philips startup screen is displayed,
then the TV returns to standby mode. This is normal behaviour.
When the TV is disconnected and reconnected to the power
supply, the startup screen is displayed at the next startup. To
switch on the TV from standby, press on the remote control or
the TV.
The standby light keeps on blinking
Disconnect the power cable from the power outlet. Wait 5
minutes before you reconnect the power cable. If the blinking
reoccurs, contact Philips TV Consumer Care.
Wrong menu language
Change the language back to your language.
1 - Press  and select Setup and press OK.
2 - Select TV settings > General settings > Menu language and
press OK.
3 - Select the language you want and press OK.
4 - Press , repeatedly if necessary, to close the menu.
Picture
No picture / distorted picture
• Make sure that the antenna is properly connected to the TV.
• Make sure that the correct device is selected as the display
source.
• Make sure that the external device or source is properly
connected.
Sound but no picture
• Make sure that the picture settings are set correctly.
Poor antenna reception
• Make sure that the antenna is properly connected to the TV.
• Loud speakers, unearthed audio devices, neon lights, high
buildings and other large objects can influence reception quality.
If possible, try to improve the reception quality by changing the
antenna direction or moving devices away from the TV.
• If reception on only one channel is poor, fine-tune this
channel.
Poor picture from a device
• Make sure that the device is connected properly.
• Make sure that the picture settings are set correctly.
Picture settings change after a while
Make sure that Location is set to Home. You can change and
save settings in this mode.
A commercial banner appears
Make sure that Location is set to Home.
Picture does not fit the screen
Change to a different picture format. Press .
Picture format keeps changing with different channels
Select a non 'Auto' picture format.
Picture position is incorrect
72

Advertisement

Table of Contents

   Also See for Philips 32PHH4509

   Related Manuals for Philips 32PHH4509

This manual is also suitable for:

32pht450940pfh450940pft450950pfh450950pft4509

Comments to this Manuals

Symbols: 0
Latest comments: