Ordering Replacement Supplies How to Order • Consult the dealer where you purchased your printer. • Consult an Oki Data Authorized Sales or Service Dealer. (For the nearest dealer, call 1-800-654-3282.) • U.S., Puerto Rico, Guam, U.S. Virgin Islands only: Order on the Internet www.okidata.com...
: The … which appears in these Note steps indicates that you should keep pressing the button repeatedly until you see the display indicated. To reset the printer menu to its original default settings: 1. Press to enter the Menu mode. 2. Press …...
Changing Default Media Settings Media Weight Trays 1 & 2 To Change the Media Weight Default for Trays 1 & 2 : The default media weight Note setting for Trays 1 and 2 is Medium. Note : The … which appears in these steps indicates that you should keep pressing the button repeatedly until you see the...
Changing Default Media Settings MP Tray To Set Transparencies as the Default Media in the MP Tray Note : For the MP Tray, the default Media Type setting is Plain. Note : The … which appears in these steps indicates that you should keep pressing the button repeatedly until you see the display indicated.
Page 9
Changing Default Media Settings MP Tray (cont.) To Set Heavy Paper, Labels, or Envelopes as the Default Media in the MP Tray : For the MP Tray, the default Note Media Size setting is Letter and the default Media Type setting is Plain.
Page 10
… MPT MEDIATYPE YYYY† † YYYY LABELS STOCK NTER 4. Press , press The setting is engaged and the second line of the display stops blinking. 5. Press 6. You’re done! CARD N INE The printer goes back on line.
Loading Media Trays 1 & 2 Media Weight Range Media Size Range: Tray 1 Capacity: Optional Tray 2 Capacity: Tray 1:16 to 32 lb. US Bond (60 to 120 g/m Tray 2:16 to 47 lb. US Bond (60 to 177 g/m Letter, Legal-14, Legal-13.5, Legal-13, A4, A5, A6, B5, Executive, Custom (min.
100 sheets of 20-lb. paper, 50 transparencies, 10 envelopes Takes: Labels: max. feed stack = about 3/8-inch (1 cm) high Letterhead stationery: • Single-sided printing: load face up, top edge into the printer. • Double-sided printing: load face down with top edge away from the printer. metric)
Minimum = 3.94" x 5.83"; maximum = 8.5" x 14". MP Tray Only: banners, one sheet at a time, 8.25 to 8.5 '' wide by up to 47.25'' long Custom sizes must first be defined in the printer driver. Exit Tray Media Weight •...
Labels Specifications Insert labels in the Multi-Purpose tray: • label side up • top edge aimed into the printer. Caution! Labels must be able to withstand 446°F (230°C) for 0.2 second, including mechanical pressures to 25 psi (1.8 kg/cm Usable...
• Card Stock Media Weight • Tray1: Heavy • MP Tray & Optional Tray2: Heavy, Ultra Heavy Recommended • Oki Premium Card Stock (see page 18) Printing Thick Paper Printing Individual Jobs on Thick Paper Make the following settings in the printer driver as you print the job: •...
V-flap seals: Media Type Rear Only Setting Making Envelopes the Default Print Media for the MP Tray Set the printer menu to (see page 8): • PaperSize = COM-10 ENVELOPE Media Recommended Weight OKI 52206301 Setting OKI 52206302...
White, 8½'' x 11'' (216 x 279 mm) 250 sheets/box – 60 lb. = Heavy – 90, 110 lb. = Ultra Heavy For best results: Humidity 40 to 65%RH To purchase Oki media, contact your local Oki dealer or visit us at www.okidata.com...
Print the Demo Page 1. Press … INFORMATION MENU NTER 2. Press … PRINT MENU MAP EXECUTE 3. Press … DEMO1 EXECUTE NTER 4. Press The Demo page prints and the printer goes back on line.
Setting Power Save Parameters Power Save Power Save sets how long the printer waits before going into standby mode. This saves energy, but the printer requires time to warm up when it receives a print job or if you want to enter the menu and change settings.
Page 22
Power Save Parameters (cont.) 4. Press … POWER SAVE ENABLE† 5. Press POWER SAVE DISABLE† † Pressing the button toggles back and forth between Enable and Disable. NTER 6. Press , press The new setting is engaged and the second line of the display stops blinking.
Press ON LINE to switch the printer between on line and off line status. When the printer is in the Menu mode, press ON LINE to exit the Menu mode and return the printer to its previous status (on or off line).
Control Panel Lights EADY TTENTION Ready LED EADY (Green) : printer is on line. : printer is off line. Flashing receiving data. : printer is NTER Attention LED TTENTION (Red) : Warning or Error status : Normal status. Flashing : Alarm status.
CAUTION! Fuser may be HOT! To remove the sheet if it is trapped in the fuser, reach inside the printer and push the fuser pressure release lever (1) towards the front and down, and pull out the sheet. Then let go of the fuser pressure release lever.
Clearing Media Jams (cont.) Jam 381 OPEN TOP COVER 381: PAPER JAM Caution! The fuser (behind cyan [C] toner) may be hot. Caution! To avoid damage to the drums: • Be sure to set the drums on a flat surface. •...
Page 28
Clearing Media Jams (cont.) Warning! If the printer has been printing, the fuser will be HOT! To remove a sheet trapped in the fuser, grasp the edge of the sheet, push the fuser pressure release lever (1) towards the front and down, and lift out the sheet.
Clearing Media Jams (cont.) Jams 370, 373 & 383 OPEN DUPLEX COVER nnn: PAPER JAM nnn = 370, 373, 383...
Page 31
Clearing Media Jams (cont.) CAUTION! Fuser may be HOT! If the sheet is trapped in the fuser, lift the top cover, reach in and push the fuser pressure release lever (1) towards the front and down, and pull out the sheet. Then let go of the fuser pressure release lever.
Clearing Media Jams (cont.) Jam 390 CHECK MP TRAY 390: PAPER JAM If the Sheet Has Just Begun to Enter the Printer If the Sheet Can’t Easily Be Pulled Out from the Front...
Changing Toner Cartridges Toner Cartridge Order #s, see page 3 Note: Use only Type C6 Toner. REPLACE TONER nnn: XXXX TONER EMPTY nnn: XXXX = 410: YELLOW 411: MAGENTA 412: CYAN 413: BLACK 1 Power off! 1 = Cyan 2 = Magenta 3 = Yellow 4 = Black 4 Make sure the lever is pulled all the way forward before...
Page 37
Changing Toner Cartridges (cont.) Important! TONER LOW disappear from the display. If it doesn’t, try printing a page. If it still doesn’t disappear, reinstall the toner cartridge. message should...
What to Do Open the cover. Push the lock lever toward the back of the printer as far as it will go. Close the cover. If this does not clear the message, call your local service dealer.
Page 39
Error Messages (cont.) SET XXX ON MPTRAY AND PUSH ON-LINE SWITCH The printer has received a job for printing from the Multi-Purpose Tray and no media is loaded in the tray. What to Do Load the requested media ( the Multi-Purpose Tray, then press ON LINE.
Page 40
: If the message still appears, Note push the blue latches at either end of the fuser back (toward the printer cover hinge) and lift the fuser out, then lower it back into the printer, pushing it firmly down in place. You should feel the latches at either end engage.
Page 41
First … Consult the store where you purchased your printer. OKI is a registered trademark of Oki Electric Industry Company, Ltd. 3M is a trademark or registered trademark of 3M. AmEx is a registered trademark of American Express Co. Avery is a registered trademark of Avery Dennison Corporation.