Table of Contents
Advertisement
COMpLeTe INSTaLLaTION
CHeCKLIST
q
Check that all parts are now installed. If there is an extra
part, go back through steps to see what was skipped.
q
Check that you have all of your tools.
q
Dispose of/recycle all packaging materials.
q
Check dryer's final location. Be sure vent is not crushed
or kinked.
q
Check that dryer is level. See "Level Dryer".
q
Remove blue film on console and any tape remaining on
dryer.
q
Wipe dryer drum interior thoroughly with a damp cloth to
remove any dust.
q
Read "Dryer Use" in your Use and Care Guide.
q
For power supply cord installation, plug into a grounded
outlet. For direct wire installation, turn on Power.
q
Select a Time Dry heated cycle, and start dryer. Do not select
Air Only Temperature setting.
If dryer will not start, check the following:
• Controls are set in a running or "On" position.
• Start button has been pushed firmly.
• Dryer is plugged into an outlet and/or electrical supply.
• Household fuse is intact and tight, or circuit breaker has not
tripped.
• Dryer door is closed.
This dryer automatically runs an installation diagnostic routine
at the start of its first cycle.
NOTE:
You may notice an odor when dryer is first heated. This
odor is common when heating element is first used. The odor
will go away.
DOOr reVerSaL
If you prefer to reverse the door swing on your dryer:
A door reversal kit, Part Number W10277499 is available
n
to order. For further information, see "Assistance or Service"
section in your Use and Care Guide, or to download
door reversal instructions on your computer, have your model
number ready, and go to www.whirlpool.com.
TrOUbLeSHOOTINg
Try these solutions to possibly avoid costs of a service call...
Dryer Operation
Dryer will not run:
Has a household fuse blown, or has a circuit breaker
n
tripped? Electric dryers use 2 household fuses or circuit
breakers. Check that both fuses are intact and tight, and
breakers have not tripped. Replace fuse or reset circuit
breaker. If problem persists, call an electrician.
Is correct power supply available? Electric dryers require
n
240-volt power supply. Check with a qualified electrician.
Was a regular fuse used? Use a time-delay fuse.
n
Dryer drum turns, but no heat:
Has a household fuse blown, or has a circuit breaker
n
tripped? Electric dryers use 2 household fuses or circuit
breakers. Replace fuse or reset circuit breaker. If problem
persists, call an electrician.
Dryer displaying code message:
On models with a time display:
"PF" (power failure) Check the following: Was drying cycle
n
interrupted by power failure? Press and hold START to restart
dryer.
Try the following:
Check if a household fuse has blown or circuit breaker has
tripped. Electric dryers use two household fuses or breakers.
Replace fuse or reset circuit breaker.
Confirm power cord is properly installed. Refer to "Electrical
Connection" section for details.
Select a Timed Dry heated cycle, and restart dryer.
If message persists, consult a qualified electrician.
"F" Variable (F1E1, F2E2, F3E1, F3E2, F7E1, F3E6, F3E7)
n
service codes: Call for service.
On models without a time display window:
"WET" indicator light is flashing and all other display/
n
indicator lights on control panel are off: Call for service.
Dryer Results
Clothes are not drying satisfactorily, drying times are
too long, or load is too hot:
Is lint screen clogged with lint? Lint screen should be
n
cleaned before each load.
Is exhaust vent or outside exhaust hood clogged with lint,
n
restricting air movement? Run dryer for 5-10 minutes. Hold
hand under outside exhaust hood to check air movement. If
you do not feel air movement, clean exhaust system of lint or
replace exhaust vent with heavy metal or flexible metal vent.
Are fabric softener sheets blocking grille? Use only one
n
fabric softener sheet, and use each only once.
Is exhaust vent correct length? Check if exhaust vent is too
n
long or has too many turns. Long venting increases dry time.
15
Advertisement
Table of Contents
