Operation; Programming - Normstahl Magic 1000 User Manual

Deleting (all) remote transmitter(s):
During one of the 3 status messages A, B or C (seeChapter
10), press the pushbuttons
seconds, FL flashes in the display. The status message
reappears after 3 seconds.

17 Operation

CAUTION: Mishandling the product can result in
injuries or material damage. Follow the basic safety
rules:
When opening or closing the door, do not block the interior or
exterior swivel ranges. Keep children away.
The door movements can be activated or stopped using the
remote transmitter provided or via switching elements such
as the wall keypad, which can be connected if desired.
Optional external features (such as the EMERGENCY
STOP) can also be connected to the door operator.
The operator must be connected to a door before
it is used. If it is not, incorrect load values will be
taught in to the electronic system. This can cause
malfunctions.

18 Programming

Switch on programming mode
During one of the 3 status messages A, B or C (seeChapter
10) press the Menu pusbutton
seconds. The display changes to the menu (D).
Select programming menu
Select the desired menu with the pushbuttons
Show / change menu value
Displays: Press the Menu pushbutton
seconds, the menu value (E) is displayed.
Change: Change the value with the pushbuttons
Save: Press the Menu pushbutton
seconds, the programming menu (D) is displayed.
Exit programming mode
Press the Menu pushbutton
the display changes to the status message, changes are
saved.
If no key is pressed within 15 seconds during programming, it
automatically exits the programming mode.
ATTENTION: If the values of the programming
menu A0 to A4 are changed, the load switch-off no
longer provides any protection! Teach the door operator in
again before re-commissioning. For this carry out
the door operator (Chapter 15) .
Magic 1000
and simultaneously for >6
for longer than 1.5
and .
for less than 1.5
and
for less than 1.5
for longer than 1.5 seconds,
Teaching in
N000925 12/2010
Menu
A0 Length SOFT RUN OPEN in 7cm
000..009
A1 Length SOFT RUN CLOSE in 7cm
000..009
A2 Soft running speed (CLOSE) mm/s
000= 50...009= 140
A3 Backjump, OFF= 000 ON= 001
A4 Change in direction, OFF= 000 ON= 001
Setting (with +/-) only possible if EMERGENCY
STOP plug (1, green) is unplugged.
A5 Added load OPEN
A6 Added load CLOSE
A7 Door type: Overhead sectional door/one-piece
door = 000
Side sectional door* = 001
Side sectional door with soft start = 002
* Obstruction release also in OPEN direction
A8 Warning time (OPEN/CLOSE) 001=2sec...
008=16sec
A9 Accessory card
000= ZKMagicS
001= ZKMagic
b0 Relay 1 (with ZKMagic accessory card)
000= no function
001= E-lock
002= warning light *
002= photo cell test* (interruption transmitter
voltage)
004= status display*: Door in end position OPEN
005= status display*: Door in end position
CLOSED
006= green light*
007= red light*
* if A9= 001
b1 Relay 2 (with ZKMagic accessory card)
000= no function
.
001= E-lock*
002= warning light *
002= photo cell test* (interruption transmitter
voltage)
004= status display*: Door in end position OPEN
005= status display*: Door in end position
CLOSED
006= green light*
007= red light*
* if A9= 001
b2 Closing edge protection, for accessory card
ZKMagic and if A9= 001
000= OFF
b3 Empty run detection 000= OFF 001= ON
b4 Automatic closing
000= OFF
001.0.010 keep-open time secs.*
(001 = 5secs... 010 = 50secs)
011..040 keep-open time min*
(011=1min... 040=30min) * plus warning time
* only active if door was fully opened
b6 Maintenance interval
000= OFF
001..009 (1,000 door movements)
Example: 005 = 5,000 door movements
The operator lighting flashes after every door
movement when the maintenance interval has run
out. A misadjustment resets the counter of the
maintenance interval.
Function, setting range, unit
1)
000..009
1)
000..009
001= OSE 002= 8k2
1)
*, secs. and min.
Factory setting
002
004
005
001
000
003
003
000
000
000
000
000
000
001
000
000
11 / 214