Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Nuvo Koolspace 110
Summary of Contents for Nuvo Koolspace 110
- Page 1 1 1 0 / 2 2 0 CELLAR k o o l s p ac e ASSEMBLY & OPERATION MANUAL...
-
Page 2: Before You Start
(above 75ºF) or humid (above 50%R.H.). Outlet power must be a DEDICATED separately fused, grounded, 15 Amp 110 - 120 V line or 7.5 Amp - 240 V line rated for your unit (CHECK BOX OR SERIAL NUMBER LABEL ON UNIT FOR YOUR LINE VOLTAGE REQUIREMENTS). -
Page 3: Hardware Kit
HARDWARE KIT Cam Cap x 20 (x24)* x 20 (x24)* In Cooling Unit Box Hex Bolt (Flange) *NOTE : Hardware quantities for Model 220 are indicated in parenthesis. Hex Bolt Hex Wrench x 14 Cam Pin x 20 (x24)* Panel Insulation Strip ~ 3 ~... -
Page 4: Step 1 : Panel Preparation
CAUTION : 1. Watch for sharp staples on boxes. 2. DO NOT STEP ON PANELS 3. The manual will give a recommended order to open boxes, it saves space and time. Open Box VP1. Install INSULATION STRIP (H) to Back, Top, and Bottom Panels. -
Page 5: Step 2 : Cabinet Assembly
STEP 2 : CABINET ASSEMBLY Attach Top and Bottom to Back by CAREFULLY aligning edge holes over Cam Pins and gently push together to avoid damaging cam pins. DO NOT BANG OR SLAP PANELS TOGETHER!!! Insert Cam, push all the way in under panel level (may require some force) and make sure Arrow points to outside edge, use allen key provided or #3 phillips screwdriver. - Page 6 Cam Arrow faces away from outside edge when tightened. Place cabinet against a wall to push sides in place. Insert Cam Cap (A) in all Cam Holes. ~ 6 ~ 2 HOLES FOR MODEL 110 3 HOLES FOR MODEL 220 � � � �...
- Page 7 STEP 3 : HINGE,BASE AND LEGS INSTALLATION Open Box VP3. Fasten one HINGE (found in door box) to the SIDE of the cabinet with Hexbolts (B). NOTE : Hinge can be on either side of the cabinet. Fasten BASE to the BOTTOM of the cabinet (FRONT BASE has to be set with Base Tabs Fasten BASE with HEX BOLTS (B)
- Page 8 STEP 4 : SHELVES ~ 8 ~ Open box VP4 Hook SHELVES into hangers starting from the bottom of cabinet PRESS BOTTOM HINT : CENTER SHELVES ON HANGERS Snap SHELVES into hangers on one side Push the SHELVES down to snap into opposite side hangers...
- Page 9 STEP 5 : COOLING UNIT INSTALLATION GET HELP BEFORE INSTALLING AND KEEP CHILDREN CLEAR OF CELLAR CONSTRUCTION AREA. Get helper to help guide unit, keep light cord clear of edge inside cellar and to prevent tipping of cellar. MAKE SURE INSULATION STRIP IS IN CORRECT ORIENTATION. Run light cord through Cut-out. Slide unit into the back opening by angling unit A to allow light cord to clear and straighten to push in B .
- Page 10 STEP 6 : LIGHT AND LIGHT COVER INSTALLATION Plug cord to LIGHT Insert LIGHT to LIGHT COVER LIGHT COVER Insert to holes pre drilled on front edge of TOP panel. ~ 10 ~...
-
Page 11: Step 7 : Door Installation
STEP 7 : DOOR INSTALLATION Insert DOOR onto BOTTOM HINGE Install TOP HINGE with HEX BOLTS (B) NOTE : ~ 11 ~ Adjust final position of the door before tightening the bolts and move cellar into place, leaving 4” clearance all around cellar. MAKE SURE CABINET IS AIRTIGHT! Adjust level... - Page 12 CONTROLS : FEATURES: - Default SET temperature 57º F/14º C (ideal for wine storage). - Calibration option of the temperature sensor. - Display of actual temperature by request. - SET temperature range 52ºF-64ºF. - Digital temperature sensor. - Dual display Fº/Cº. - Settings are stored in memory for power failures.
- Page 13 3 rows 3" dia. 2 rows 4.5" dia. Max: 110 3" bottles Bottles in black will be in the cold air stream and could block airflow efficiency in some circumstances (warm or humid areas). This area of the cabinet should have the coldest temperature and may be used as your “chilling”...
-
Page 14: Troubleshooting Guide
Although each Vintage Keeper cooling unit has been carefully tested at every stage of manufacture, occasional problems arise, the majority of which are due to rough or careless handling during shipping or installation. Other problems may derive from improper cabinet assembly, power interruption or surge, low line voltage (less than your unit rating of 105V or 240V), or failure to clean the unit regularly (see illustration below). - Page 15 LIMITED WARRANTY AND PRODUCT SUPPORT ONE YEAR LIMITED WARRANTY If your Koolspace cooling unit or cabinet fails to perform as designed within one year of the date of purchase, VINTAGE KEEPER INC. warrants that, upon your request, it will be repaired or replaced, at our option, during the one year warranty period. This warranty applies only to the first end-user purchaser of a Koolspace unit that is purchased and used in the continental United States or Canada (excludes Alaska and Hawaii).
- Page 16 1 1 0 / 2 2 0 CELLAR k o o l s p ac e Toll free: 1-888-274-8813 www.koolspace.com...