Download  Print this page

Declaration Of Conformity; Lawn Preparation - Bosch Indego l Original Instructions Manual

Robotic mower
Hide thumbs

Advertisement

Table of Contents
OBJ_BUCH-1573-005.book Page 29 Tuesday, December 17, 2013 12:59 PM
Robotic Mower
Protection class
Frequency
Output DC
Degree of protection
Weight
*depends on cutting height, grass conditions and moisture
**Subject to variant
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your garden product. The trade names of the individual garden products may vary.
Noise/Vibration Information
Measured sound values determined according to EN 60335.
Typically the A-weighted noise levels of the product are:
Sound pressure level 64 dB(A); sound power level 72 dB(A).
Uncertainty K =2.74 dB.

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60335
(battery powered product) and EN 61558 (battery charger)
according to the provisions of the directives 2011/65/EU,
2009/125/EC, 2006/95/EC, 2004/108/EC, 2006/42/EC,
2000/14/EC.
2000/14/EC: Guaranteed sound power level 75 dB(A). Con-
formity assessment procedure according to Annex VI.
Equipment category: 32
Notified body:
SRL, Sudbury, England, Nr. 1088
Technical file (2006/42/EC, 2000/14/EC) at:
Bosch Lawn and Garden Ltd., PT-LG/ENS,
Stowmarket, Suffolk IP14 1EY, England
Henk Becker
Helmut Heinzelmann
Executive Vice President
Head of Product Certification
Engineering
PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
07.10.2013
Explanation of Installation Guide
(see pages 3–12)
Action
Delivery scope/unpacking product
Position the docking station
Thread wire through base plate
Connect first end of perimeter wire
Fix docking station to the ground
Bosch Power Tools
Hz
V
kg
Action
Lay out perimeter wire
Connect second end of perimeter wire
Clip on protective cover of docking station
Install power supply
Docking station indicates power on
Plug in isolator key
Charge battery by putting the machine into dock-
ing station
Welcome screen = Refer to manual
Lift up and carry the machine
Set height of cut
Logicut Intelligent Cutting
Cleaning
Maintenance

Lawn Preparation

Remove stones, loose pieces of wood, wire, live mains cables
and other foreign objects from the cutting area.
Make sure that the cutting area is even and has no ditches,
grooves and steep slopes above 20° that are clear obstruc-
tions for the machine.
Cut the main area of the lawn with a conventional mower to a
max. height of 40 mm and the perimeter wire area to a max.
height of 20 mm.
Installation
For a video guide on how to install the Indego please visit
www.bosch-indego.com or use the following QR-Code.
Figure
1
Select a position for the docking station, horizontally leveled
and out of direct sunlight.
2 – 3
Note: The docking station must be positioned on the wire at
4
an outer edge of the cutting area. It cannot be positioned by
5
the side of a shed or workshop that appears as an island with-
6
in the cutting area.
English | 29
Indego
Indego 1300
/II
/II
50/60
50/60
42
42
IP44
IP44
2.0
2.0
Figure
7
8
9
10
11
12
13
14
15
16
17
A
B
F 016 L81 082 | (17.12.13)

Advertisement

Table of Contents
loading

This manual is also suitable for:

Indego 1300