Advertisement
Available languages
Available languages
FRONT PANEL FEATURES
3
22
23
4
2
24
1
5
8
7
9
10
21
1.
Mic /Aux Button: Activates Mic /Aux inputs.
2.
Mic /Aux Gain: Adjusts the volume of the
microphone and AUX inputs.
3.
Mic Treble: Adjusts the high-tone of the
microphone.
4.
Mic Bass: Adjusts the low-tone of the microphone.
5.
Channel Gain: Adjusts the pre-fader input level.
6.
Channel Treble: Adjusts the high-tone level.
7.
Channel Middle: Adjusts the middle-tone level.
8.
Channel Bass: Adjusts the low-tone level.
9.
Input Selector: Selects what input source is routed
to the channel from the rear panel connected units.
10. Channel Fader: Adjusts the level sent to program
mix.
11. Headphone Volume: Adjusts the volume level of
the headphone output.
12. Headphone Jack: Your headphones can be
connected to this ¼" terminal. The volume should
always be set at its lowest setting while connecting
and disconnecting headphones to prevent damage to
headphones and/or your hearing.
13. Cue Slider: Channels 1 and 2 can be previewed
using this mini-crossfader. Sliding this to the left
plays the left "channel-1" and sliding to the right
plays the right "channel-2".
14. Cue Meter: Audio level display of the cue output.
Depending on the Cue Selector switch, this could be
Master, CH1-CH2 mini cue-fader mix, or FX. When
in CH-1-CH-2 this meter shows the peak, "PFL", Pre
Fader levels of channels 1 and 2. You can use the
channel "Gain" and "EQ" controls to match the levels
of input signals while cueing.
15. Cue Selector: The cue selector has 3 modes:
a. Master: The Master Output is routed to the
headphones.
b. FX: The FX block output is routed to the
headphones. This allows you to cue the FX
before applying it.
c. CH1-CH2: Allows cueing of CH1-CH2 using the
mini cue-fader
16. Replaceable Crossfader: Blends audio between the
channels assigned to the left and right assign
switches.
Note: This fader is user replaceable if it should ever
wear out. Simply remove the facepanel and then
remove the screws holding it in position. Replace
the fader with a quality authorized replacement from
your local Numark retailer.
26
25
27
5
6
8
7
6
17
18
9
10
20
20
14
16
12
17. Crossfader Direction Button: Activation of this
switch reverses the assignment of CH-1 and CH-2 on
19
the crossfader.
18. Crossfader Slope Control: The position of this
knob determines how quickly or intensely the
15
crossfader will blend.
19. Master Output Knob: Adjusts the main output
11
volume.
20. Master Meter: Shows audio level of the master
13
output.
21. KILL Switches: Eliminate High, Mid, or Low
frequencies for a unique effect.
22. Effects Assign: Selects channel to be processed.
23. Effects Process: activates the processor.
24. Effect Select: Sets desired effect.
25. Rate/Frequency: Adjust the Rate/ Frequency of the
effect. Depending on the selected effect, this can be
a continuous control or synchronized to the beat.
26. Effect Mix: Adjusts amount of effect to be blended
21
with the original sound.
27. Beat Tap: Tap this button to the tempo (or half the
tempo) to align effects to the music. Press and hold
the button to disable beat synch control.
REAR PANEL FEATURES
Note: It is recommended that the mixer be turned
off before connecting and disconnecting any
sources to the inputs of the mixer.
1. Microphone Input: Microphones with a ¼"
connector can be connected to this input terminal.
2. Phono Inputs: This input is used for connecting
your turntables through the sensitive RIAA phono
preamplifiers. Only turntables with phono level
output should be attached.
and other devices may be attached if the Phono/Line
rear panel switch is set to the line position.
3. Phono/Line Source Switch: This switch activates
and deactivates the sensitive RIAA phono
preamplifiers. Only turntables with phono level
output should be assigned when the switch is
in the phono position. Some turntables offer line
level output. To use these turntables and other line
devices like CD players, switch the input to Line.
4. GND: This screw connector should be used to secure
any turntables or other devices connected to the
mixer that need to be grounded.
5. Line Inputs: CD players, Tape Decks, Samplers or
other line level input devices should be connected to
these inputs.
6. Record Output: This RCA output is for connecting a
recording device such as a tape deck or CD recorder.
The level of the record output is based upon pre-
master levels.
7. Master Output (RCA): This output is for connecting
an external monitoring device such as a PA system,
powered monitors or a home stereo. The level of the
master stereo output signal is controlled by the
master fader.
8. AC In: This mixer is designed to work with the
power supply assembly that comes with the unit.
While the power is switched off, plug the power
supply into the mixer first, then plug it into the
outlet.
9. Power Switch: Use this switch to turn on the mixer
after all input devices are already connected to
prevent damage to your equipment. Turn the mixer
on before you turn on amplifiers and turn of
amplifiers before you turn off the mixer.
3
9
8
7
6
5
4
4
3
1
2
5
2
Line level turntables
Advertisement
