Related Manuals for Nostalgia Electrics SCC-200
Summary of Contents for Nostalgia Electrics SCC-200
- Page 1 SNOW CONE CART™ Model # SCC-200 For Household Use Only! Read These Instructions Before Using This Unit! SAVE THESE INSTRUCTIONS!
-
Page 2: Important Safeguards
ENGLISH IMPORTANT PRECAUTIONS Appliance Specifications: 120 Volts 60 HZ 100 Watts ETL Approved Important Precautions to Remember: NEVER immerse in water. NEVER use near water. NEVER use an abrasive sponge or cloth. NEVER use a scouring pad on the unit. NEVER leave unit unattended while in use. - Page 3 ENGLISH IMPORTANT SAFEGUARDS (Continued) DO NOT use outdoors. DO NOT let the cord hang over the edge of table or counter tops, or touch hot surfaces. DO NOT place on or near a hot gas or electric burner, or in a heated oven. Extreme caution must be used when moving this appliance.
- Page 4 ENGLISH ASSEMBLY After Taking the Unit Out of the Box: Your SNOW CONE CART™ requires some assembly before first use. The Main Unit, which includes the ice grinder, is already assembled. You will need to put together the cart itself using the instructions that follow. Before first use, make sure to wipe clean the inside of the Main Unit with a non-abrasive moist sponge, a non-abrasive towel, or a damp cloth followed by a non-abrasive dry towel.
- Page 5 ENGLISH ASSEMBLY (Continued) ASSEMBLY Main Unit Base Support Open the box and remove all parts including the Main Unit, Storage Compartment, Wheels, Legs, and all other contents (including the Push Handle and accessories). Attach the Push Handle to the Storage Compartment using four of the #1 screws (as shown below): Screws, Studs, and Nuts Storage...
- Page 6 ENGLISH ASSEMBLY (Continued) Connect the Base Supports by screwing two of the #1 screws into the Cross Bar (as shown below): Connect the Leg Assembly by screwing four of the #3 studs from the Base Support into the Leg Assembly (as shown below). Make sure to screw from the Base Support into the Leg Assembly and not vice versa.
- Page 7 ENGLISH ASSEMBLY (Continued) Attach the Wheels to the Base Support by using two of the #4 Wheel Rods. Slide a #5 Lock Washer onto a Wheel Rod, and then push the Wheel Rod through the holes in the Base Support. Make sure to place the two #6 Flat Washers between the Base Support and the Wheels.
- Page 8 ENGLISH USING YOUR SNOW CONE CART™ USING YOUR SNOW CONE CART™ First, find a stable surface near an electrical outlet before starting. (Make sure your cord is away from any water source. If needed, it is acceptable to use an extension cord.) Before plugging in your unit, add ice cubes by removing the clear lid from the Main Unit of your SNOW CONE CART™.
- Page 9 ENGLISH REPLACING THE BLADE (Continued) When following the next three steps, use EXTREME CAUTION as the blade is very sharp! Once the Ice Tray is removed, you are fully exposed to the blade inside! 2. Once the Disassembly Tool is properly inserted, twist counter-clockwise (as the arrow shows) and lift the Ice Hopper out.
- Page 10 ENGLISH CLEANING Make sure the unit is unplugged before cleaning. Open the housing door to clean and dry inside of unit using a slightly damp, non- abrasive sponger or non-abrasive towel. Also use a slightly damp, non-abrasive sponge or non-abrasive towel to wipe clean outside of unit, then wipe with a non-abrasive dry towel to dry.
-
Page 11: Customer Service
Customer Service Inquiry form and click the Submit button. A representative will contact you as soon as possible. SNOW CONE CART™ SCC-200 Limited Warranty This appliance is designed and built to provide many years of satisfactory performance under normal household use. The distributor pledges to the original owner that should there be any defects in material or workmanship during the first 90 days of purchase, we will repair or replace the unit at our option. - Page 12 Nostalgia Products Group LLC 1471 Partnership Dr. Green Bay, WI 54304-5685 Visit Us Online at www.nostalgiaelectrics.com ©2009 Nostalgia Products Group LLC Rev. 4/28/09...
Need help?
Do you have a question about the SCC-200 and is the answer not in the manual?
Questions and answers
I fill the hopper with ice cubes and shut the lid. When I turn the machine on, it makes a loud whiny sound. When I removed the ice, shut the lid and turned it in, everything worked. What am I doing wrong?
A loud whiny sound when using the Nostalgia Electrics SCC-200 ice machine could be caused by ice cubes that are too hard or too cold. For optimal shaving results, the manual recommends letting ice cubes sit for a short while before putting them in the shaving unit. Using overly hard or fresh-from-freezer ice may cause strain on the blades or motor, resulting in a loud noise.
This answer is automatically generated