Front Panel Removal And Installation; Remote Controller Installation; Optional Kit Installation - Fujitsu 9318739183 Installation Manual

Table of Contents

Advertisement

Overlap the insulation
Connection pipe
(heat insulation)
Bind the pipes together
so that there is no gap.
Pipe
Drain hose
Left piping
Connection cable
Pipe
Drain hose
Check the following:
Drain hose
GOOD
Saddle

8. FRONT PANEL REMOVAL AND INSTALLATION

8.1. Intake grille removal
(1) Open the intake grille.
(2) Pull down the knob.
(3) Lift the intake grille upward, until the axle at the top of the intake grille is removed.
8.2. Intake grille installation
(1) The fi xing axle of the intake grille is installed on the Panel.
(2) Lay down the intake grille.
8.3. Front panel removal
(1) Remove intake grille (Reference the intake grille removal.)
(2) Remove 6 screws.
(3) The thumb is hung on the lower part as shown in the fi gure, and it pulls to the front,
pushing [▲] mark , and bottom hooks (2 position) is removed from wall hook bracket.
(4) The front panel is pulled to the front, raising the upper surface, and a front panel is
removed.
8.4. Front panel installation
(1) First, fi t the lower part of the front panel, and insert top and bottom hooks. (3 top
sides)
(2) Attach the 6 screws.
(3) Attach the intake grille.
Intake grille
Mounting shaft
Bearing
Front panel
Screws (6 position)
Push
[▲] mark
Push
Top holes (two sides)
Top hole (center)
Indoor unit
Indoor unit pipe
(heat insulation)
Vinyl tape
Wrap with cloth tape
Cloth tape
For connection from the left rear
Wall pipe
Connection cable
Drain hose
Connection pipe
PROHIBITED
Lifted up
Wave
End in water
Intake grille
Knob
Front panel
Front panel
Wall hook bracket
Top hook (center)
Front panel
Top hooks
(2 sides)
Install the Front panel and Intake grille securely. If installation is imperfect, the Front
panel or Intake grille may fall off and cause injury.

9. REMOTE CONTROLLER INSTALLATION

• Check that the indoor unit correctly receives the signal from the remote controller,
then install the remote controller holder.
• Select the remote controller holder selection site by paying careful attention to the
following:
Avoid places in direct sunlight.
Select a place that will not be affected by the heat from a stove, etc.
9.1. Remote controller holder installation
• Install the remote controller a maximum distance of 22 ft. (7 m) from the remote control
receiver. However, when installing the remote controller, check that it operates correctly.
• Install the remote controller holder to a wall, pillar, etc. with the tapping screw.
Remote controller holder fi xing
Remote controller
holder
Tapping
screw
(small)

10. OPTIONAL KIT INSTALLATION

This air conditioner can be connected with the following optional kits.
• Wired remote controller
• Simple remote controller
• External connect kit
Before installing wired remote controller
10.1.
• When you use wired remote controller, some functions may not be used.
Please use the recommended optional remote controller.
• Before installing, be sure to disconnect all power supply.
• Don't touch the heat exchanger.
• During installing or removing operation, be sure not to have wire caught by parts or
draw it hard. Or it may result troubles to the air-conditioner.
• Avoid place in direct sunlight.
• Select place that will not be affected by the heat from a stove, etc
• Before setting up the optional kit, please confi rm whether air-conditioner can receive
the signal.
• Do not connect the wired remote controller to the terminal for power supply.
• When connecting the wired remote controller with the indoor unit, use the connecting
cable (supplied with wired remote controller or simple remote controller).
• Recommended cable length of wired remote controller is 32 ft. (10 m). Make sure to
do insulate of connecting part when extended the cable.
Remote controller cable modifi cation
10.2.
(1) Use a tool to cut off the terminal on the end of the remote controller cable, and then
remove the insulation from the cut end of the cable.
(2) Connect the remote controller cable and connecting cable.
(supplied with wired remote controller)
Important: Be sure to insulate the connection between the wires.
Remote
controller cable
Remote
controller cable
CAUTION
CAUTION
Remote controller mounting
(1) Set
(2) Push
Remote
controller
CAUTION
Connecting cable
White
Red
Black
White
Red
Insulated
connection
Black
En-7

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents