DECT Industrial Handset User Guide Table of Contents TABLE OF CONTENTS ... 2 HANDSET INFORMATION ... 4 GENERAL ... 5 ... 5 ANDSET ... 6 ISPLAY INSTALLATION... 7 NSTALLING THE HARGER OUNTING THE ... 7 HARGING RACK 3.5. ATTERY ANAGEMENT 3.5.1.
Page 3
DECT Industrial Handset User Guide ERSONAL HONE 6.4.1 Add Personal Phone Book Entry... 20 6.4.2 Edit a Number in the Personal Phone Book ... 21 6.4.3 Edit a Name in the Personal Phone Book ... 22 6.4.4 Delete Personal Phone Book Entry... 22...
This product is classified with IP52 classification as defined in EN60529. Ensure the adapter voltage is the same as the electrical outlet voltage. The DECT Industrial Handset uses radio signals and does not guarantee a connection in all circumstances. Do not rely on a cordless telephone to make emergency calls.
DECT Industrial Handset User Guide GENERAL 2.1 Handset The handset has 22 keys which are described as follows: Voice (short press) & E2 (long press) Message function. In Menu - Cursor left After a digit - delete last digit. Long press - delete all.
DECT Industrial Handset User Guide Display Three lines, of 12 alphanumeric characters in length, can show text or caller information. The bottom line displays 5 icons, they are described as follows: ON – Handset in range OFF – Handset out of range ON –...
DECT Industrial Handset User Guide 3 INSTALLATION Installing the Charger Connect the power line cable to the back of the charger and then plug the AC adapter into the mains socket outlet. Wall Mounting the Charger • Drill two holes in the wall, with a horizontal spacing of 45 mm and insert the screws.
DECT Industrial Handset User Guide Installation of the Chargers on the Charging Rack The chargers can be placed in two different positions, depending on the usage of the chargers. If the chargers are placed on the desktop the chargers should be connected with 2 screws.
DECT Industrial Handset User Guide 3.7. Operating Times Standby time - up to 90 hours. Talk time – up to 10 hours. 3.8. Battery Charging Information The battery capacity can be checked using the menu option. As follows: 1. Press the key to enter the menu display and use the Menu battery.
DECT Industrial Handset User Guide Issue 02 Note: When the handset is placed in the charger, the vibrator and B-answer (auto answer functions are disabled. 3.10 Low Battery Warning If the battery capacity reaches a certain minimum value: On-Hook • The display flashes battery low.
DECT Industrial Handset User Guide INITIAL SETUP Initial Setup and Operation The handset can be operated on a maximum of 10 DECT systems. Before you can make a call via a DECT system, the handset has to be subscribed to the Meridian 1.
DECT Industrial Handset User Guide The default handset name ‘PHILIPS’ is displayed on handsets that are not subscribed. When the handset cannot be subscribed to the system, the display will show ‘subscription failed’. Press the return to the stand-by display.
DECT Industrial Handset User Guide Selecting a DECT System (Roaming) Roaming between Meridian 1 systems is only possible when the handset is subscribed to each system. Manual To switch between DECT systems manually: 1. Press the key to enter the menu display and use the menu login.
DECT Industrial Handset User Guide 5 USING THE HANDSET A complete menu tree is located at the end of this document for reference. Operating in Standby Mode The menu feature operates as follows: 1. Press the key to enter the menu display.
DECT Industrial Handset User Guide The keypad lock can be activated by pressing the the * key. The same operation is required to deactivate the keypad lock. ‘KEY LOCKED’ is displayed when the keypad lock is activated. Volume Control The volume switch for the earpiece is located at the right hand side of the handset.
DECT Industrial Handset User Guide Note: When deleting a digit, use the digit to the right of the digit to be removed. Press the to remove the digit. 2. Press the key to dial the number. 3. Press the key to end the call.
DECT Industrial Handset User Guide To dial a number from the personal phone book: 1. Press the key to enter the Phone Book. The first entry appears in the display. If the phone book is empty, the 2. From this display, there are 2 methods to find a name: - Use the key to move through the personal phone book entries.
DECT Industrial Handset User Guide 5.5.5 Caller List (CLIP) When the handset rings and the call is not answered, it will be stored in the Caller list (CLIP). The Caller list contains a maximum of 10 entries. The entries in the Caller list and the Redial list can be accessed the same way.
DECT Industrial Handset User Guide If automatic call answering is used, the phone call will be accepted automatically. It is not necessary to press the 5.7 Silent Mode In Silent mode the handset will use the vibrator instead of ringer and bleep sounds.
DECT Industrial Handset User Guide Microphone Mute The microphone mute can be activated or deactivated during conversation by pressing key. When the microphone mute is active the display shows MIC. MUTED. Personal Phone Book Press the key to enter the Phone Book.
DECT Industrial Handset User Guide 3. Press the key to enter the number. The display will show NAME:, type in a name using the alphanumeric keys. 4. Press the key to enter the name in the phone book and return to the stand-by mode again.
DECT Industrial Handset User Guide Note: When deleting a digit, use the digit to the right of the digit to be deleted. Press the remove the digit. 6.4.3 Edit a Name in the Personal Phone Book To edit a personal phone book entry: 1.
DECT Industrial Handset User Guide To delete a personal phone book entry: 1. Press the key to enter the phone book and select the entry to be deleted. 2. Press the key to select this entry for deletion. The display will show 'DELETE?' 3.
DECT Industrial Handset User Guide 4. The DN and password can also be entered to access voice mail directly. Note 1: It is possible for another party to determine the password of your voice mail if it is programmed. Note 2: Long press the * for a pause.
DECT Industrial Handset User Guide 4. Press the key to return to stand-by mode. Settings Within a profile the user can define several settings. These are described in the following sections. Each setting will have a default as shown in the table below.
DECT Industrial Handset User Guide 6.10 Ringer Volume The 5-step ringer volume option enables users to set the loudness of the bleep and ringing tones. To set the ringer volume: 1. Enter the Set Profile display and use the 2. Press the key to enter the ringer volume display.
DECT Industrial Handset User Guide Issue 02 6.12 Vibrator The vibrator functions when the handset is ringing or bleeping, it vibrates in the same pattern as the ringer or bleep sound. To switch the vibrator ON/OFF: 1. Enter the Set profile display use the key to select vibrator.
DECT Industrial Handset User Guide 6.14 Start Volume The 5-step start volume option enables users to set the loudness of the earpiece to a certain value to start from. Adjustment during conversation can be made with the – and the + keys at the side of the handset. After conversation the volume is set to the start volume setting.
DECT Industrial Handset User Guide Issue 02 show backlight on or backlight off before switching to the Set Profile display. 7 OUT OF RANGE Each handset is equipped with an out of range detection option. There are three detection mechanism for out of range. They are: 1.
DECT Industrial Handset User Guide Issue 02 9 SHORTCUT LIST The following features can be accessed easily via the shortcuts mentioned in the table below. Galway M1 Design Support...
DECT Industrial Handset User Guide 10 MENU TREE KIRK MENU PROFILE LOGIN SET UP CAPACITY SET PROFILE INDOORS (1) SET PROFILE1 SET PROFILE1 SET PROFILE1 BACKLIGHT RINGERTONE RINGER VOL. BACKLIGHT RINGERTONE RINGER VOL ON/OFF 1,2... MENU SELECT LOGIN LOGIN SYSTEM 01*...