Nortel Ethernet Routing Switch 8010 Installation Manual
Nortel networks switch installation guide
Hide thumbs
Also See for Nortel Ethernet Routing Switch 8010:
- Installing and maintaining (108 pages) ,
- Installing (14 pages)
Related Manuals for Nortel Nortel Ethernet Routing Switch 8010
Summary of Contents for Nortel Nortel Ethernet Routing Switch 8010
- Page 1 Installing the Passport 8010 Chassis Part No. 204518-B April 2000 4401 Great America Parkway Santa Clara, CA 95054...
-
Page 2: Statement Of Conditions
In the interest of improving internal design, operational function, and/or reliability, Nortel Networks NA Inc. reserves the right to make changes to the products described in this document without notice. Nortel Networks NA Inc. does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. - Page 3 Japan/Nippon Requirements Only Voluntary Control Council for Interference (VCCI) Statement Taiwan Requirements Bureau of Standards, Metrology and Inspection (BSMI) Statement Canada Requirements Only Canadian Department of Communications Radio Interference Regulations This digital apparatus (Passport 8010 Chassis) does not exceed the Class A limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.
-
Page 5: About This Guide
For information about available switch modules for this chassis, consult your Nortel Networks Reseller. For detailed information about setting up your network and using Nortel Networks switches, refer to the documentation for the switch modules you install in the chassis. -
Page 6: Before You Begin
Before You Begin The physical requirements for installing the Passport 8010 Chassis in an equipment rack are: • Adequate room (13.1 spaces) is provided in an EIA or IEC standard 19-inch (48.2-centimeter) equipment rack that is: — Bolted to the floor —... - Page 7 8 = Screws for brackets and equipment rack 9 = Cable guides For detailed information about the comm port cable for the Passport 8132TX Switch Module, refer to the documentation that was shipped with that module. To purchase a replacement shipping carton assembly for the Passport 8010 Chassis, contact the manufacturer (Tharco) at 1-800-772-2332.
-
Page 8: Attaching The Rack-Mounting Brackets
Attaching the Rack-Mounting Brackets Required tool: Phillips screwdriver Note: Each bracket fits only one side of the chassis. If the mounting holes do not line up between a bracket and the chassis, try that bracket against the other side of the chassis. Hold each rack-mounting bracket against one side of the chassis. -
Page 9: Installing The Chassis In A Rack
Installing the Chassis in a Rack Required tool: Phillips screwdriver Slide the chassis into the rack. 9074FA Insert and tighten the rack-mounting screws. To complete the installation process, refer to “Installing the Power Supply.” 9075FA... -
Page 10: Installing The Power Supply
Installing the Power Supply Required tool: Phillips screwdriver If necessary, remove the filler panel from a power supply bay. Note: If you are installing a power supply in a new chassis, be sure to remove the bag of dessicant from the middle power supply bay. Align and tighten the retaining screws. - Page 11 Turn on the power switch. Note: In a newly installed chassis that requires two power supplies (nonredundant configuration), you must turn on both units within 2 seconds of each other. If you wait longer to turn on the second power supply, both power supplies will turn off. To correct this condition, turn off both power supplies, wait at least 30 seconds, and turn both power supplies on again within 2 seconds.
- Page 12 Attaching a Cable Guide Attach the cable guides to the left side of the chassis so the bundled cables will not obstruct airflow to the right side of the chassis. Loosen, but do not remove, the rack-mounting screws needed to install one cable guide.
-
Page 13: Installing A Module
Installing a Module For details about the operation of modules, refer to the documentation that was shipped with each module. Required tool: Phillips screwdriver Remove a filler panel from a module slot. Align the module circuit board with the card guides in the chassis. -
Page 14: Chassis Specifications
Align and tighten the retaining screws. Chassis Specifications Environmental Specifications Operating temperature: Storage temperature: Operating humidity: Storage humidity: Operating altitude: Physical Specifications Height: Width: Depth: Weight (Empty): Weight (Fully Loaded): Cooling System Fan Trays: Fans: Thermal Sensors: 9071FA 0° to 40° C (32° to 104° F) –25°... - Page 15 Electrical Specifications System Line Frequency System with one power supply or two supplies in redundant configuration: System with two power supplies (nonredundant) or three supplies in redundant configuration: Electromagnetic Immunity RF Susceptibility: Electrostatic discharge (ESO): Electrical Fast Transitions (EFT/B): Electromagnetic Emissions Meets requirements of: Safety Agency Approvals UL Listed...
Need help?
Do you have a question about the Nortel Ethernet Routing Switch 8010 and is the answer not in the manual?
Questions and answers