Whirlpool WDT780SAEM User Manual page 5

Activates the TargetClean™ spray jets and provides
intensified water spray to back of lower level rack.
May add heat and time to cycle.
Raises main wash temperature to improve cleaning for
loads containing tough, baked-on food.
Sanitizes dishes and glassware in accordance with NSF
International NSF/ANSI Standard 184 for Residential
Dishwashers. Certified residential dishwashers are not
intended for licensed food establishments. Only sanitizing
cycles have been designed to meet the requirements of
the NSF/ANSI 184 performance standard for soil removal
and for sanitization efficacy. There is no intention, either
directly or indirectly, that all cycles on a NSF/ANSI 184
certified dishwasher meet the NSF/ANSI 184 performance
standard for soil removal and for sanitization efficacy.
The Sanitize indicator glows at the end of the cycle if the
Sani Rinse option was successfully completed. If the
indicator does not activate, it is probably due to the cycle
being interrupted.
Dries dishes with heat. This option, with the use of rinse
aid, will provide the best drying performance. Plastic items
are less likely to deform when loaded in the top rack. Use
High Heat Dry for optimum dry performance, Turn the
Heat Dry option off for air dry.
Runs dishwasher at a later time. Select a wash cycle and
options. Each time you press the delay button it will display
the next available delay time. Press DELAY. Press START/
RESUME. Close door firmly.
NOTE: The dishwasher remembers the last Delay you
selected. To reset the delay time to something other than
what is displayed, continue to press the Delay button until
the desired delay time is reached.
NOTE: Anytime the door is opened (such as, to add a
dish); Start/Resume must be pressed again to resume
delay countdown.
Avoids unintended use of dishwasher between cycles, or cycle and option changes during a cycle.
To turn on Lock, press and hold SANI RINSE/CONTROL LOCK or DELAY (depending on model) for 3 seconds. Control Lock light
will stay on for a short time, indicating that it is activated, and all buttons are disabled. If you press any button while your dishwasher
is locked, light flashes 3 times. Dishwasher door can still be opened/closed while the controls are locked.
To turn off Lock, press and hold SANI RINSE/CONTROL LOCK or DELAY (depending on model) for 3 seconds. Light turns off.
NOTE: If your model requires you to press and hold DELAY to lock controls, Control Locked LED will be on or off to indicate whether
Control Lock is active or not.
Control
OPTIONS
Purpose Comments
Press to start or If the door is opened during a cycle or the power is interrupted, the Start/Resume button LED
resume a wash flashes. Cycle will not resume until door is closed and Start/Resume is pressed.
cycle.
NOTE: If Start/Resume button is located on top of door, push door firmly closed within 3
seconds of pressing Start/Resume. If door is not closed within 3 seconds, Start/Resume button
LED will flash, an audible tone will be heard (on some top control models), and cycle will not
start.
Press to cancel Close the door firmly. The dishwasher starts a 2-minute drain (if needed). Let dishwasher drain
wash cycle. completely. Press and hold START/RESUME for 3 seconds.
CAN BE
SELECTED
WITH WHAT IT DOES
Sensor Raises main wash
Heavy
temperature from
Normal
105°F (41°C)
to120°F (49°C).
Sensor Raises the main
Heavy
wash temperature to
Normal
135°F (57°C)
Soak & Clean
Sensor Raises the main
Heavy
wash temperature to
Normal
135°F (57°C) and
the final rinse
temperature to
156°F (69°C)
Sensor Uses heating
Heavy
element to speed
Normal
drying times. Heat
Dry option defaults
Soak & Clean
to ON when any
1 - Hour Wash
cycle is selected
except for 1- Hour
Wash.
Available with Delays start of a
any cycle
cycle up to 24 hours
5
ADDED
ADDED WATER
TIME TO GALLONS
CYCLE (LITERS)
0:12 to 0:57 0 to 4.8
(0 to 18.2)
0:05 to 0:13 0 to 3.86
(0 to 14.6)
0:05 to 1:06 0 to 3.86
(0 to 14.6)
0:08 to 0:46 0
0:00 0
.