Intended Use; Technical Data; Declaration Of Conformity - Bosch Rotak 32 Ergoflex Original Instructions Manual

OBJ_BUCH-1739-001.book Page 9 Wednesday, August 15, 2012 8:26 AM
It is recommended for increased electrical safety to use a Resid-
ual Current Device (RCD) with a tripping current of not more
than 30 mA. Always check your RCD every time you use it.
For products not sold in GB:
WARNING: For your safety, it is required that the plug at-
tached to the machine is connected with the extension cord.
The coupling of the extension cord must be protected against
splash water, be made of rubber or coated with rubber. The
extension cord must be used with a cable strain relief.
The connection lead must be inspected for signs of damage at
regular intervals and may only be used if in perfect condition.
If the supply cord is damaged, it must be replaced by a Bosch
Service Centre.
Products sold in GB only: Your product is fitted with an
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
et elsewhere.
Products sold in AUS and NZ only: Use a residual current de-
vice (RCD) with a rated residual current of 30 mA or less.
Maintenance
Always wear gardening gloves when handling or work-
ing near the sharp blades.
Keep all nuts, bolts and screws tight to be sure that the ma-
chine is in safe working condition.
Check the grass catcher frequently for wear or deteriora-
tion.
After use ensure machine is clean before storage. Ensure
air vents are clean and free from debris. If necessary clean
debris with a soft dry brush.
Examine the machine and replace worn or damaged parts
for safety.
Ensure replacement cutting means of the right type are
used.
Ensure replacement parts fitted are Bosch approved.
Symbols
The following symbols are important for reading and under-
standing the operating instructions. Please take note of the
symbols and their meaning. The correct interpretation of the
symbols will help you to use the garden product in a better
and safer manner.
Symbol Meaning
Movement direction
Reaction direction
Bosch Power Tools
Symbol Meaning
Wear protective gloves
Weight
Switching On
Switching Off
Permitted action
Prohibited action
Accessories/Spare Parts

Intended Use

The garden product is intended for domestic lawn mowing.

Technical Data

Lawnmower
Article number
Rated power input
Blade width
Height of cut
Grassbox, capacity
Weight according to
EPTA-Procedure 01/2003
Protection class
Serial number
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your garden prod-
uct. The trade names of the individual garden products may vary.
Noise/Vibration Information
Measured sound values determined according to
2000/14/EC (1.60 m height, 1 m distance away).
Typically the A-weighted noise levels of the product are:
Sound pressure level 79 dB(A); sound power level 93 dB(A).
Uncertainty K =1 dB.
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60335:
2 2
a <2.5 m/s , K =1.5 m/s .
h

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under "Technical data" is in conformity with the fol-
lowing standards or standardization documents: EN 60335
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC, 2000/14/EC.
English | 9
Rotak 32
Ergoflex
3 600 H85 E..
W 1200
cm 32
mm 30 – 60
l 31
kg 8.6
/II
see type plate on the
garden product
F 016 L70 926 | (15.8.12)