Bosch 0 602 207 Original Instructions Manual page 28

High-frequency straight grinder
Hide thumbs Also See for 0 602 207:
Table of Contents

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 27
OBJ_BUCH-640-001.book Page 28 Thursday, September 17, 2009 12:24 PM
28 | English
4) Power tool use and care
a) Do not force the power tool. Use the cor-
rect power tool for your application. The
correct power tool will do the job better
and safer at the rate for which it was de-
signed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch
is dangerous and must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any adjust-
ments, changing accessories, or storing
power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfa-
miliar with the power tool or these in-
structions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for mis-
alignment or binding of moving parts,
breakage of parts and any other condi-
tion that may affect the power tool's op-
eration. If damaged, have the power tool
repaired before use. Many accidents are
caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Prop-
erly maintained cutting tools with sharp
cutting edges are less likely to bind and
are easier to control.
g) Use the power tool, accessories and tool
bits etc. in accordance with these in-
structions, taking into account the work-
ing conditions and the work to be per-
formed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qual-
ified repair person using only identical
replacement parts. This will ensure that
the safety of the power tool is maintained.
3 609 929 B78 | (17.9.09)
Safety Warnings for Straight Grinders
Safety Warnings Common for Grinding
This power tool is to be used as a grinder.
Observe all safety warnings, instructions,
illustrations and specifications provided
with this power tool. Failure to follow all in-
structions listed below may result in electric
shock, fire and/or serious injury.
This power tool is not suitable for sanding
with sanding discs, working with wire
brushs, polishing and cut-off grinding. Op-
erations for which the power tool is not de-
signed may create a hazard and cause per-
sonal injury.
Do not use accessories which are not spe-
cifically designed and recommended by the
tool manufacturer. Just because the acces-
sory can be attached to your power tool, it
does not assure safe operation.
The rated speed of the accessory must be at
least equal to the maximum speed marked
on the power tool. Accessories running fast-
er than their rated speed can break and fly
apart.
The outside diameter and the thickness of
your accessory must be within the capacity
rating of your power tool. Incorrectly sized
accessories cannot be adequately guarded
or controlled.
The arbor size of wheels, flanges, backing
pads or any other accessory must properly
fit the spindle of the power tool. Accesso-
ries with arbor holes that do not match the
mounting hardware of the power tool will run
out of balance, vibrate excessively and may
cause loss of control.
Do not use a damaged accessory. Before
each use inspect the accessory such as abra-
sive wheels for chips and cracks, backing
pad for cracks, tear or excess wear, wire
brush for loose or cracked wires. If power
tool or accessory is dropped, inspect for
damage or install an undamaged accessory.
After inspecting and installing an accessory,
Bosch Power Tools

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents