Connecting a TV and a video recorder SCART Switching on for the first time • Plug in your Mediamaster. • The “First time installation”menu is shown. • Press the select button on the remote control to start the installation proce- dure.
Quick Guide Time adjustment Select cursor up/down to adjust the time in half-hour increments. To adjust the minutes, select cursor left/right . • Press select to finish the installation and to open the Navi Bars. GB 4...
General information The “Control” and “Settings” folders Nokia, Nokia Connecting People and Navi Bars are registered trademarks of Nokia Corporation. Other product and company names mentioned herein may be trademarks or trade names of their owners. Nokia operates a policy of continuous development. Therefore we reserve the right to make changes and improvements to any of the products described in this manual without any prior notice.
Nokia Home Communications (“Nokia”). The Agreement authorizes You to use the Software specified in Clause 1 below and which is included in this Nokia digital TV receiver. This is an agreement on end-user rights and not an agree- ment concerning sale.
User as defined above, and You will not transfer the Soft- ware to any Government End User without a license. 9. CONTACT DETAILS. If You want to contact Nokia in re- spect of this Agreement, contact Nokia at the following...
• Do not allow the unit to be exposed to hot, cold or humid conditions. • Service should be carried out only at a Nokia Authorised Service Centre. • Please note that the only way to isolate the Mediamaster completely from...
REMOTE CONTROL This section describes how to operate the Mediamaster using the buttons on the remote control. Some of the functions can also be performed by using the buttons on the front panel. Press once to turn the sound off/on (mute). Press and hold for a few seconds to switch the Mediamaster in and out of standby mode.
FRONT AND REAR PANEL Front panel LED 1 Function Standby Locked to channel Remote control feedback SW download Error Rear panel digital audio S/PDIF digital out- put for connection to a HiFi system mains lead audio L R RCA connectors 110-240 V AC Stereo outputs for connection to a HiFi...
CONNECTING THE MEDIAMASTER The box for your Mediamaster should contain the following items: • the Mediamaster • remote control with 2 AAA batteries • SCART cable (fully connected; 1.0 metre) • mains cable • RF cable • Owner’s manual with software license agreement About the SCART sockets The rear panel of the Mediamaster is equipped with 2 SCART sockets (see dia- gram).
CONNECTING THE MEDIAMASTER Note the following: • In some block of flats, the roof-mounted aerial system includes a filter and chan- nel selector. If so, the aerial will probably not work with the Mediamaster, in which case you should contact your landlord. •...
CONNECTING THE MEDIAMASTER Connection of a video recorder • Connect a SCART cable from the main SCART socket on the TV to the TV SCART socket on the Mediamaster. • Connect an RF cable from the TV/VCR output on the Mediamaster to the RF input socket on the video.
CONNECTING THE MEDIAMASTER Procedure when RF connections are used This procedure is only necessary when your Mediamaster is connected to the TV with an RF lead and no SCART leads have been used. To tune your TV to the RF signal, it is possible that you will need both this manual and the manual for your TV.
FIRST TIME INSTALLATION General information Once your Mediamaster has been correctly connected, a “First time installation” must be performed. During this procedure, helpful information is displayed at the bottom of the menus. NOTE: The select button always confirms a selection in these menus; therefore, pressing it will take you to the next step in the installation process.
FIRST TIME INSTALLATION Channel search in progress This menu will be shown while the Mediamaster is searching for TV and radio channels. All channels found will be listed on the screen. Note that the search procedure may take a few minutes. You may cancel the search at any time by pressing select.
NAVI BARS General information • Press select to open the Navi Bars . Use the Navi Bars , which consist of a horizontal bar and a vertical bar, to select TV or radio channels and/or change system settings. The horizontal row contains folders named TV, Settings , etc. Their names are shown in black at the bottom of each folder.
NAVI BARS The “Control” and “Settings” folders Both of these system folders contains a few bookmarks. Each of these bookmarks contains menus from which you can choose different settings. The system folders cannot be deleted. The manual will now explain the different settings you can make from the Control and Settings folders, starting with the bookmarks from the Contr ol folder.
NAVI BARS ☛ Control folder Edit channels From these menus, you can create and edit favourite channel lists. You can add, delete, rename and arrange the order of the channels within the favourite lists. The “TV” list might contain a lot of channels. By creating your own favourite lists, you can make it more convenient to manage channels.
NAVI BARS • Enter the name as follows : Press the number corresponding to the character you want: once for the first character, twice for the second, etc. The available characters are listed below: * # & % $ , ! ; - + ) / \ @ ^ 1 a b c 2 Å...
NAVI BARS Add/Delete channels From this menu, you can add and remove the channels in your favourite lists. The “TV” or “Radio” lists are used as a basis for where the channels are selected from. A channel is added or removed from the list by pressing info. The square on the righthand side of the line will be empty for removed channels, and will contain an “x”...
NAVI BARS ☛ Contr ol folder Timer General You can make the Mediamaster start and stop at a predefined time. The timer function is very useful when you want to record a programme and you cannot start/stop the recording event yourself, or when you just want to be re- minded of the start of a programme you do not want to miss.
NAVI BARS ☛ Settings folder Channel This menu is used when you want to search for channels at a later time. To open it, you will be asked to enter your access code. The access code is set to 1234 at the factory. A channel search procedure can be performed in three different ways: Automatic, Manual or Advanced manual search.
NAVI BARS ☛ Settings folder To open this menu, you will be asked to enter your access code. The access code is set to 1234 at the factory. From this menu, you can adjust the audio/video settings for your Mediamaster. TV screen format Select your TV screen format.
This is used to change the access code from the default, factory-set 1234. This code is used to access any Mediamaster function that requires it, e.g. access code. If you forget the access code that you have set, contact and Nokia Authorised Serv- ice Centre for assistance.
NOTE: Do not turn off the Mediamaster, use the remote control or disconnect the antenna cable while downloading as this will damage the software and the receiver will need to be sent to a Nokia Authorised Service Centre. ☛ Settings folder Reinstall To open this menu, you must enter the access code.
VIEWING MODE General Information The following describes the basic functions of your Mediamaster while watching digital terrestrial TV . In addition to the normal functions like switching the Mediamaster in/out of standby, changing the volume, etc., there are some other useful functions that will be ex- plained in this part of the manual.
VIEWING MODE Extended programme information The Mediamaster can display information about programmes currently being broad- casted as well as those that will be broadcasted next. This procedure is the same for both TV and radio mode. By pressing info while watching TV, you will get the “Programme information” ban- ner.
VIEWING MODE TV Release (0) With the 0 button, you can toggle between externally connected equipment, such as a digital terrestrial TV or a video recorder, which must be switched on.) (This is only valid when the units are connected via SCART cables, and not by RF connection.) Teletext Pressing txt will open a teletext page, if teletext is transmitted.
GLOSSAR Y OF TERMS AC-3 Multichannel digital audio encoding system. Access Authorisation to use the coding system to purchase / order TV pro- grammes. Access code A four-digit code stored in the Mediamaster. Used to lock/unlock the Mediamaster. Access control A feature that allows parents to ”lock”...
TROUBLESHOOTING Problem The LED on the front panel does not light up/is not lit. The left LED is red. The remote control is not working. You have forgotten your PIN code. During the first time installation when the Mediamaster tries to find and store channels you get the message “No channels found”.
TECHNICAL SPECIFICATIONS Transmission Standar ds DVB, MPEG 2, OFDM RF input Modulator output In-/output connector IEC female / IEC male RF input frequency 174-300; 474-862 MHz RF input power level -78 to -30 dBm RF impedance 75 Ω Frequency range Loop through 47-862MHz Frequency range RF modulator 470-862 MHz...
Nokia is a registered trademark of Nokia Corporation www.nokia.com 00000936.00...