Download  Print this page

Nokia CK-200 User And Installation Manual

Nokia cell phone user manual
Hide thumbs

Advertisement

Nokia Car Kit CK-200
User and Installation Guide
Issue 2.0 EN

Advertisement

Table of Contents
loading

  Also See for Nokia CK-200

  Summary of Contents for Nokia CK-200

  • Page 1 Nokia Car Kit CK-200 User and Installation Guide Issue 2.0 EN...
  • Page 2 Reproduction, transfer, distribution, or storage of part or all of the contents in this document in any form without the prior written permission of Nokia is prohibited. Nokia operates a policy of continuous development. Nokia reserves the right to make changes and improvements to any of the products described in this document without prior notice.
  • Page 3: Table Of Contents

    Contents For your safety... 5 Quick start... 6 First time setup ... 6 Remote control ... 6 1. Introduction ... 8 About this document... 8 Software updates ... 8 Bluetooth wireless technology ... 9 2. Get started... 10 Parts ... 10 Remote control CU-13R ...
  • Page 4 radio system ... 37 Installation using the ISO cable CA-160... 38 Installation using the power cable CA-153P and an external speaker... 40 Installation using the power cable CA-153P and direct input cable CA-161... 42 Installer settings... 43 Optional accessories... 44 Charging cable ...
  • Page 5: For Your Safety

    For your safety Read these simple guidelines. Not following them may be dangerous or illegal. Read the complete user and installation guide for further information. SWITCH ON SAFELY Do not switch the device on when wireless phone use is prohibited or when it may cause interference or danger.
  • Page 6: Quick Start

    Q u i c k s t a r t Quick start This section briefly describes the basic features of the car kit. For details, see the respective sections in this guide. ■ First time setup 1. Switch on the car kit (see p. 15) and your mobile device. 2.
  • Page 7 • To adjust the volume during a call or to scroll through menu items, turn the wheel left or right. • To select, for example, function in the menu, press the wheel. 4. Call key • To make or answer a call or to switch between an active call and a call on hold, press the call key.
  • Page 8: Introduction

    I n t r o d u c t i o n 1. Introduction With the Nokia Car Kit CK-200, you can make and answer calls hands free. You can also copy the contacts list from your two compatible mobile devices to the car kit and view the copied contacts on the built- in display to make calls through the connected device.
  • Page 9: Bluetooth Wireless Technology

    I n t r o d u c t i o n Download and install the Nokia car kit updater application from www.nokia.com/support to a compatible computer. Use a USB data cable that has a standard USB plug at one end and a micro USB plug at the other end, to connect the car kit display to a computer.
  • Page 10: Get Started

    ■ Parts The car kit contains the following parts: 1. Main unit CK-200 with display 2. Mounting plate for main unit CK-200 3. Remote control CU-13R with Navi wheel 4. Steering wheel mount for remote control CU-13R 5. CD that contains this guide In addition, the sales package includes cables and other parts that are needed when installing the car kit.
  • Page 11: Remote Control Cu-13R

    ■ Remote control CU-13R You can use the remote control to operate the car kit. The device has a Navi wheel that you can turn or press. 1. Voice dialling / mute key 2. Switch key 3. Navi wheel 4. Call key 5.
  • Page 12: Rotate The Display

    G e t s t a r t e d Rotate the display When the display is attached to the dashboard using the supplied mounting plate, you can rotate the display in the ball joint up to about 15 degrees left, right, up, or down.
  • Page 13: Display Indicators

    To search for a contact in the contacts list of the car kit, turn the wheel right. To view the last dialled numbers, press the call key. See also “Recent calls”, p. 23. Display indicators You have an active call. You have a call on hold.
  • Page 14: Insert The Remote Control Battery

    G e t s t a r t e d ■ Insert the remote control battery The wireless remote control is powered by one CR2032 lithium coin cell battery. Replace the battery only with the same or equivalent type. 1. Slide the cover away from the device (1).
  • Page 15: Navigate The Menus

    G e t s t a r t e d ■ Navigate the menus To open the list of menu functions in standby mode, press the wheel when Menu is displayed. To scroll to an item (such as a menu function) or through a list, turn the wheel.
  • Page 16: First Time Use

    Bluetooth devices. For instructions, see the user guide of your device. 3. On your device, select the car kit (Nokia CK-200) from the list of found devices. 4. On your device, enter the Bluetooth passcode 0000, to pair and connect the device to the car kit.
  • Page 17: Connect The Car Kit Manually

    In some devices, you may need to make the connection separately after pairing. If pairing succeeds, the car kit is displayed in the list of currently paired Bluetooth devices in your device, and the paired device is displayed in the Connection manager menu of the car kit. When the car kit is connected to your device and ready for use, the Bluetooth name of the device is displayed.
  • Page 18 G e t s t a r t e d When you switch on the car kit and it connects to two devices, the first connected device becomes the primary device and the other device the secondary device. In standby mode, the name of the primary device is shown above the secondary one.
  • Page 19: Basic Use

    B a s i c u s e 3. Basic use ■ Copy contacts from connected devices You can copy contacts (names and phone numbers) from compatible mobile devices that you connect to the car kit. is displayed during copying. Copying may take several minutes, depending on the number of contacts.
  • Page 20: Make A Call

    B a s i c u s e You can only use the contacts of connected devices if you have copied them to the car kit. Make a call You can use the remote control to make calls only on the primary device. To make a call on the secondary device, set the device as primary, or make the call from that device.
  • Page 21: Answer Or Reject A Call

    B a s i c u s e Voice dialling To activate voice dialling (if your device supports this feature with the car kit), press the voice dialling key when no call is in progress. Say the voice tag of the desired contact clearly. If the car kit is connected to two devices, voice dialling is activated on the primary device.
  • Page 22: Adjust Speaker Volume

    B a s i c u s e ■ Adjust speaker volume To adjust the speaker volume during a call, turn the wheel. In some installation setups, the volume can also be adjusted from the car radio. The selected volume is saved for the current device. To set the default volume for calls, see “Audio settings”, p.
  • Page 23: Send Tone Strings

    For compatibility, go to www.nokia.com/support. ■ My own key The My own key menu is only displayed if the Nokia Accessory Setup Application is installed in the device that is connected to the car kit. If the application is not already installed in your device, to check the...
  • Page 24 When you select this menu, the car kit performs the function that you have specified for a short press of the My own key in the Nokia Accessory Setup Application. You can set the car kit to read out loud a new text message, call your favourite number, or reject a call and send a predefined text message.
  • Page 25: Settings

    4. Settings ■ Connection settings To manage Bluetooth connections, in standby mode, select Settings > Connection and from the following: • Connection manager compatible device, select previously paired device or disconnect a device, select the device from the list. • Multipoint connection at the same time.
  • Page 26: General Settings

    S e t t i n g s ■ General settings In standby mode, select Menu following: • Speed dials Assign phone numbers to the speed dial numbers (1-9) — for the connected device (if two devices connected, the primary device).
  • Page 27: Audio Settings

    • Audible menu Set the car kit to play some voice prompts, such as — the names of main menus. For information on available languages, go to www.nokia.com/support. • Audio routing Select which sounds of the connected device are —...
  • Page 28: Troubleshooting

    T r o u b l e s h o o t i n g 5. Troubleshooting ■ Reset the car kit The car kit doesn’t react to my actions. How can I reset it? Detach the display from the mounting plate for at least 10 seconds, and press the power key to switch on the car kit.
  • Page 29: Other Issues

    T r o u b l e s h o o t i n g • If the car kit is connected to an optional speaker, check that the car kit volume is set properly. • Make sure you have not accidentally muted the speaker volume. •...
  • Page 30: Installation

    Observe the following safety guidelines when installing the car kit. • Only a qualified service technician should install or service the car kit using the approved original Nokia parts supplied in the sales package. Faulty installation or service may be dangerous and may invalidate any warranty which may apply to the car kit.
  • Page 31: Update The Software

    Before you install the car kit, update the software of the car kit to the latest version. Download and install the Nokia car kit updater application from www.nokia.com/support to a compatible computer. Use a USB data cable that has a standard USB plug at one end and a micro USB plug at the other end, to connect the car kit display to a computer.
  • Page 32: Install The Car Kit In A Vehicle

    I n s t a l l a t i o n Open the updater application, and follow the displayed instructions. Keep the USB cable connected while the software is being updated. ■ Install the car kit in a vehicle This section describes how to install the car kit parts in a vehicle.
  • Page 33: Remote Control Cu-13R

    Remote control CU-13R The remote control should be located so that it is within easy reach of the user. Do not mount the remote control within the head impact area. When installing the remote control, make sure it does not interfere with or hinder the steering or other controls or systems used in the operation of the vehicle (for example, airbags).
  • Page 34: Display

    I n s t a l l a t i o n 3. Pull the strap from the end to keep it securely in place (3). 4. Press the end of the strap downwards (4), and press the catch upwards (5). 5.
  • Page 35 The display should be located so that it is clearly visible for the user and it can be easily rotated left, right, up, or down. When installing the display, make sure it does not interfere with or hinder the steering or braking systems or other controls or systems used in the operation of the vehicle (for example, airbags).
  • Page 36: Junction Box Rx-73

    1. Connector for direct input cable CA-161 2. Connector for power cable CA-153P or power cable of ISO cable CA- 3. Connector for optional speaker (such as Nokia SP-3) or speaker cable of ISO cable CA-160 4. Connector for optional charging cable (such as CA-134) 5.
  • Page 37: Integration With A Car

    I n s t a l l a t i o n Install the junction box in the car using suitable mounting material (not supplied in the sales package). Make sure the junction box stays securely in place. ■ Integration with a car radio system The car kit can be connected to a car radio system in three different ways.
  • Page 38: Installation Using The Iso Cable Ca-160

    • Check the permanent +12 V feed (red wire) and ignition feed (blue wire) on the junction box connector. If necessary, swap the configuration connectors "+12V battery" and "Ignition" of the ISO cable. CA-160 CK-200...
  • Page 39 (such as Nokia CA-134) to the junction box. • To use an external microphone (such as Nokia MP-2) instead of the built-in one, connect the microphone to the respective connector on the junction box, and modify the microphone settings (see “Installer settings”, p.
  • Page 40: Installation Using The Power Cable Ca-153P And An External Speaker

    1. Connect the wires of the power cable CA-153P to the car as follows: • The black wire to the vehicle ground. • The red wire to the permanent 12 V. Always connect the supplied 2 A fuse to this line, close to the source. CK-200...
  • Page 41 2. Connect the power cable to the respective connector on the junction box. 3. Connect the speaker (such as Nokia SP-3) to the respective connector on the junction box. 4. Connect the display to the respective connector on the junction box.
  • Page 42: Installation Using The Power Cable Ca-153P And Direct Input Cable Ca-161

    1. Connect the wires of the power cable CA-153P to the car as follows: • The black wire to the vehicle ground. • The red wire to the permanent 12 V. Always connect the supplied 2 A fuse to this line, close to the source. CK-200...
  • Page 43: Installer Settings

    (such as Nokia CA-134) to the junction box. • To use an optional external microphone (such as Nokia MP-2) instead of the built-in one, connect the microphone to the respective connector on the junction box, and modify the microphone settings (see “Installer settings”, p.
  • Page 44: Optional Accessories

    Microphone In noisy car environments, you can use an optional external microphone (such as Nokia MP-2) to improve the audio quality, instead of the built- in one. To use an external microphone, connect the microphone to the respective connector on the junction box.
  • Page 45: Check The Operation Of The Car Kit

    Note: In order to comply with RF exposure guidelines, install the external antenna so that a minimum distance of 20 centimetres (8 inches) can be maintained between the external antenna and all persons, with external antenna gain not exceeding 3 dBi. ■...
  • Page 46: Care And Maintenance

    This way you help prevent uncontrolled waste disposal and promote the recycling of materials. Check product environmental information and how to recycle your Nokia products at www.nokia.com/ werecycle, or nokia.mobi/werecycle. The crossed-out wheeled-bin symbol on your product, battery, literature,...
  • Page 47: Additional Safety Information

    A d d i t i o n a l s a f e t y i n f o r m a t i o n Additional safety information ■ Vehicles RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles such as electronic fuel injection systems, electronic antiskid (antilock) braking systems, electronic speed control systems, and air bag systems.