Table of Contents
Advertisement
TORQUE WRENCH SElllNGS
USE
Dome upper fixing screw
Cover fixing screw
Fuse block fixing screw
Twin-beam upper fixing nut
Commutator fixing screw
Cornmutator fixing nut
Relay connector fixing screw
Relay suppori upper fixing screw
Air intake fixing screw
Wheel spoke nipple
Disc fixing screw
Front axle fixing screw
Collet upper fixing screw
Collet lower fixing screw
Ring gear fixing screw
Rear wheel axle
Collet fixing screw
Dashboard fixing nut
Ring nut fixing nut
Plate guard fixing nut
Wire guard fixing screw
Muffler fixing screw
Muffler fixing strap
Power unit side fixing nut
Power unit central fixing nut
Power unit support upper fixing screw
Regulator fixing screw
Starter module fixing screw
Starter module fixing nut
Sensor fixing screw
Horn and radiaior fixing screw
Radiator support fixing screw
NOTE
-
If not otherwise specified,
Standard tightening torques
for the following t h r e a d
THREADING
M6x1
M5x0,8
M5x0,8
M5x0,8
M5x0,8
M6x1
M5x0,8
M6x1
M5x0,8
M4,07x0,75
M8x1,25
M10x1,5
M8x1
M8x1
M10x1,25
M16x1,5
MlOx1,25
M4x0,7
M8xl,25
M5x0,8
M5x0,8
M8x1 ,25
M8
M6x1
M5x0,8
M6x1
M6x1
M6x1
M6x1
M6x1
M6x1
M6x1
5x0,8
6x1
8x125
N.m.
3,9+4,9
1,9-2,9
1,9+2,9
4 , 9 4 8
3,9+4,9
9,8-11,7
2,9+3,9
11,7+13,7
3,9-4,9
3,9+4,9
39,2+44,1
63,7+68,6
39,2+44,1
39,2+44,1
58,8+63,7
83,3+88,2
49+53,9
2,9-4,9
13,7+17,6
3,9+4,9
3,9+4,9
9,8+11,7
11,7+14,7
0,9+1,8
5,81;7,8
11,7+13,7
4,9t5,8
4,9+5,8
4,9+5,8
3,9-5,8
11,7+13,7
11,7+13,7
4 , 9 4 8
8,8+9,8
21,5+23,5
0,4+0,5
0,2+0,3
02-0,3
0,5-0,6
0,4-0,5
1-1,2
0,3+0,4
1,2-1,4
0,4t0,5
0,4+0,5
4-43
6,5-7
4-43
4-43
6 4 5
8,519
5+5,5
0,3+0,5
1,4+1,8
0,4+0,5
0,4-0,5
1+1,2
1,2-1,5
0,1-0,2
0,6-0,8
1,2-1,4
0,5-0,6
0,5+0,6
0,5-0,6
0,4-0,6
1,2-1,4
1,2-1,4
0,5-0,7
0,9-1
2,2-2,4
LBlFT
2,9+3,6
1,4-2,1
1,4-2,l
3,6+4,3
2,9+3,6
7,2-8,6
2,1+2,9
8,6+10,1
2,9t3,6
2,9+3,6
28,9-32,5
47+50,6
28,9+32,5
28,9+32,5
43,4+47
61,5+65,1
36,1+39,7
2,1+3,6
10113
2,9-3,6
2,9+3,6
7,2+8,6
8,6+10,8
0,7+1,4
4,3-5,7
8,6+10,1
3,6+4,3
3,6+4,3
3,6-4,3
2,9+4,3
8,6+10,1
8,6+10,1
3,6t5
6,5+7,2
15,8+17,3
Lock all nuts and screws at the correct locking torque, using a dynarnometric wrench.
U
A screw or nut, when incorrectly locked, can be darnaged or loosen completely, with subsequent damage to the bike and
injuries to the rider. A screw or nut locked over the prescribed wrench torque Setting can be damaged, have the thread broken or
Cut down, therefore loosening completely. Above table states the list of torque wrench Settings for rnain screws and nuts, in
connection with the thread diameter, pitch and specific use.
All these figures have to be applied to threads cleaned with solvent.
Pari. N" 67600 [
1
111
911
11111111111111111111l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l l ~
x.7
l z & &
111
Advertisement
Table of Contents
