Wireless Xdp Parallel Mode - Panasonic KX-TDA50 Feature Manual

• When a PS in Wireless XDP Parallel mode is on a call, other extension users cannot perform the
following features when they call this extension:
– Executive Busy Override (→ 1.5.3 Executive Busy Override)
– Whisper OHCA (→ 1.20.3 Whisper OHCA)
• When a PS is paired with a wired telephone, most of the extension settings assigned to the wired
telephone (extension number, extension name, etc.) will be used by the PS, and the PS will use its own
extension settings once again when Wireless XDP Parallel mode is canceled. Note, however, that the
following extension settings of the wired telephone are copied to the extension settings of the PS when
Wireless XDP Parallel mode is activated, and will remain in effect for the PS after the mode is canceled.
– Call Waiting Setting (→ 1.3.9 CALL WAITING FEATURES)
FWD/Do Not Disturb (DND) Setting (→ 1.4.9 DND (Do Not Disturb), → 1.6.6 FWD (Call
–
Forwarding))
– Call Pickup Deny Setting (→ 1.3.6 Call Pickup)
– Executive Busy Override Deny Setting (→ 1.5.3 Executive Busy Override)
– Itemized Billing Code for Automatic Route Selection (ARS) (→ 1.1.3 ARS (Automatic Route
Selection))
– Calling Line Identification Presentation (CLIP) Number and CLIP Number Selection (→ 1.3.13
CLIP (Calling Line Identification Presentation))
– Calling Line Identification Restriction (CLIR) and Connected Line Identification Restriction (COLR)
Settings (→ 1.3.13 CLIP (Calling Line Identification Presentation))
– Extension Personal Identification Number (PIN) (→ 1.5.6 Extension PIN (Personal Identification
Number))
– COS Programming (→ 1.3.19 COS (Class of Service))
– Extension User Group (→ 1.7.1 GROUP FEATURES)
Transfer Recall Destination for Call Transfer and Call Park (→ 1.3.5 Call Park, → 1.3.8 Call
–
Transfer)
• The PS will retain its original settings for the following items even when in Wireless XDP Parallel mode.
These settings can be set on the wired telephone and PS independently, and the settings can be
different.
– Ring Tone Pattern Table Selection (→ 1.15.2 Ring Tone Pattern Selection)
– Preferred Line Assignment—Incoming (→ 1.10.2 Line Preference—Incoming)
– Preferred Line Assignment—Outgoing (→ 1.10.3 Line Preference—Outgoing)
– Hot Line Setting (→ 1.8.6 Hot Line)
– Display Language (→ 1.4.8 Display Information)
– ISDN Bearer Mode (→ 1.9.16 ISDN (INTEGRATED SERVICES DIGITAL NETWORK)
FEATURES)
– Flexible Button Assignment (→ 1.6.3 Flexible Buttons)
– Transfer Recall Destination for Call Transfer and Call Park (The setting assigned to the wired
telephone will first be copied to the PS's extension settings, then can be changed for the PS if
necessary.) (→ 1.3.5 Call Park, → 1.3.8 Call Transfer)
If an extension number is required when changing any PS settings while in Wireless XDP Parallel
mode, use the original extension number assigned to the PS, not the extension number of the paired
(wired) telephone.
• If the Extension Feature Clear is performed, the corresponding extension data for both the wired
telephone and the PS will be cleared. (→ 1.5.5 Extension Feature Clear)
• When a call arrives, both the wired telephone and the PS will ring. However, when one of the following
settings is made, only the telephone which was used to make the setting will ring.
– Automatic Callback Busy (→ 1.1.4 Automatic Callback Busy (Camp-on))
1.20 W
Feature Manual 325