Advertisement
5
If you chose the Advanced connection mode, select Search Access
Point and press
. Use the arrow buttons to highlight your network
name (SSID) in the list of available connections.
6
If your network has security enabled, enter your network password on
the screen that appears. Make sure to enter any uppercase or lowercase
letters in the correct case.
•
To select a number or character, use the arrow buttons on the
remote control to highlight it, then press
•
To switch between uppercase and lowercase letters, select CAPS
and press
.
•
To change the displayed symbols, select SYM1 or SYM2 and
press
.
When you're finished entering the network password, select Finish and
press
.
7
If you chose the Advanced connection mode, select IP Settings and
press
.
If your network assigns addresses automatically, make sure DHCP is
turned on. If not, turn off DHCP and enter the projector's IP Address,
Subnet Mask, and Gateway Address, as needed.
8
To prevent the SSID and IP address from appearing on the network
standby screen, set the SSID Display and IP Address Display settings
to Off.
9
When you're finished selecting settings in the Wireless LAN menu, press
Esc.
10
Select Complete and press
save your settings.
11
See "Install network software" for additional instructions.
Install network software
Install links to download the network software and manuals from the
projector CD. Downloads require an Internet connection. You can also install
the software and manuals from the Epson website, as described in "Where to
get help."
To project over the network, install the EasyMP
on each computer you will project from. To monitor and control your projector
over the network, install the EasyMP Monitor software (Windows only). To
project from multiple PCs over the network, install the EasyMP Multi PC
Projection software.
Click the icons on your desktop to download and install the software and their
manuals. See the manuals for instructions on installing and using the software.
Project wirelessly from a
mobile device
You can connect your mobile device and projector using Epson iProjection
and a QR code. Make sure the latest version of Epson iProjection is installed on
your device and the optional wireless LAN module is installed in your projector
with the PowerLite 1224.
Install the Epson iProjection app
To project from an iOS or Android
download and install the Epson iProjection app.
Visit epson.com/projectorapp (U.S.) or
epson.ca/projectorapp (Canada) for more information.
.
, then select Yes and press
Network Projection software
®
device,
™
Direct wireless connection
Make sure your device and Epson projector are not connected to a network
and your Epson projector's Connection Mode is set to Quick.
1
iProjection on your device's Home screen.
Tap
2
Tap Projector to open the Search Projector menu.
3
Tap Read QR code.
4
Point your device's camera at the QR code your projector displays; the
QR code is read automatically.
5
Tap OK to register your projector's Wi-Fi profile.
6
Tap Install to install your projector's Wi-Fi profile.
7
Tap Install Now at the Unsigned Profile notification.
8
Tap Done to exit the Profile Installed screen.
9
Tap OK to confirm the connection to the projector.
10
Note the projector network name (SSID) shown on your device's screen.
Then go to the Wi-Fi settings on your device to select that network.
Your device and Epson projector are now connected.
Network connection
Make sure your projector and mobile device are connected to the same
network.
1
Tap
iProjection on your device's Home screen.
again to
2
Tap Projector to open the Search Projector menu.
3
Tap Read QR code.
4
Point your device's camera at the QR code your projector displays; the
QR code is read automatically.
Your device and Epson projector are now connected.
Troubleshooting
If you see a blank screen or the No signal message after turning on your
computer or video device, check the following:
™
•
Make sure the Status light on the projector is blue and not flashing, and
the A/V Mute slide is open.
•
Press the Source Search button on the projector or the remote control
to switch to the correct image source, if necessary.
•
If you're using a Windows laptop, press the function key on your
keyboard that lets you display on an external monitor. It may be labeled
CRT/LCD or have an icon such as
Fn key while pressing it (such as Fn + F7). Wait a moment for the display
to appear.
•
If you're using a Mac laptop, open System Preferences and select
Displays. Click the Arrangement tab and select the Mirror Displays
checkbox.
. You may have to hold down the
Hide quick links:
Advertisement
