Table of Contents
Related Manuals for Nilfisk-Advance HSC 585
Summary of Contents for Nilfisk-Advance HSC 585
- Page 1 HSC 585 MULTI EXTRACTOR 220 - 240V EU INFORMATION & OPERATING INSTRUCTIONS CAUTION: DO NOT OPERATE MACHINE UNTIL YOU HAVE READ ALL SECTIONS OF THIS INSTRUCTION MANUAL 2 6 0 2 2 0 0 8 1 1 6 0 0 2 0 5 2 1 1 R E V A...
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories, shops, and offices other than normal residential housekeeping purposes. When using any electrical appliance, basic precautions should always be followed, including the following: NOTE: Read all instructions before using this machine. -
Page 3: Cleaning Solutions
Select a proper pre-spray for the surface to be cleaned, and apply the pre-spray. Use a neutral pH rinse or detergent (6 to 9 pH) in the HSC 585 to prevent premature wear of the pump, seals and other components. Powdered chemicals are not recommended. -
Page 4: Know Your Machine
HSC 585 MULTI Vacumm Vacuum Hose Tank Lid Connection Hoses Latch Pressure Gauge 7 Bar Quick Disconnect SWITCH PLATE HEAT SELECTED LIGHT Drain Hose Wand Holder Switches Vac Tank 85 Bar Quick Disconnect Solution Tank Garden Hose Connector Wheel Base... -
Page 5: Operation
CAUTION: IF FOAM OR WATER COMES OUT THE VACUUM EXHAUST, TURN THE MACHINE OFF IMMEDIATELY HIGH PRESSURE WASHER Before each use, inspect the machine, hoses, and cleaning tools for cleanliness and completeness. Make sure hoses are in good condition and the spray nozzle(s) is tight. - Page 6 water to a clear, solid stream. Priming may take 20 - 60 seconds, or even longer sometimes, and it will require a full solution tank. When the pump is primed, let off the Power Prime Pedal, and turn off the pump and the vacuum.
- Page 7 3. If you choose to use the auto-fill feature, connect the fill-hose to the hose connection over the solution tank fill hole. Turn on the water source, and allow the tank to fill with solution. NOTE: do not turn the water on to full pressure;...
- Page 8 USING THE AUTOMATIC-FILL AND/OR AUTOMATIC-DUMP AUTOMATIC-FILL INSTRUCTIONS Operation: 1. Attach a garden hose to the auto-fill hose connection above the holding tank fill hole, and connect the other end of the hose to your water source. 2. Make sure the float that hangs into the solution tank from the auto-fill valve is free of obstruction and can move freely.
- Page 9 AUTOMATIC-DUMP INSTRUCTIONS Operation: 1. Before each use: if necessary, unscrew the stainless steel filter inside the recovery tank and clean it. Also make sure the float in the recovery tank is clean. 2. Attach a garden hose to the automatic pump-out fitting on the back of the base of the machine (refer to illustration below).
- Page 10 HSC 585 Multi REV A 3.8.08...
- Page 11 600758545 MISCELLANEOUS PARTS AND KITS 600758521 600758533 600758534 600758535 600758540 ALWAYS USE ONLY ORIGINAL NILFISK PARTS ON YOUR HSC 585 MULTI PART LIST 220 - 240V DESCRIPTION Reel with hoses, complete Lid kit Vacuum air inlet kit Switch plate kit...
-
Page 12: In-Line Filter
ACCESSORIES HFT-45 HARD SURFACE COMBO TOOL Designed for edging hard surfaces • Hose is rated to 172 bar / 500 -2500 psi • Use water up to 110 °C / 230°F • Heads lay flat for cleaning under fixtures • Ergonomic design •... -
Page 13: Specifications
MX 585 MULTI SPECIFICATIONS: Vacuum: 3-stage Rated Power: 2950 W maximum Pump: Positive displacement, 83 bar & Demand,7 bar Suction Power: 372 W Vacuum at Nozzle: 30.4 KPA Heat: to 100 º Suction Width: 38 mm Weight: 89.5 KG Dimensions: 39”H x 21”W x 36”...
Need help?
Do you have a question about the HSC 585 and is the answer not in the manual?
Questions and answers