Ac Hookups; Before You Use Your Receiver - Sony STR-DA80ES Operating Instructions Manual

Getting Started

AC Hookups

Setting the voltage selector (only on the
models supplied with the voltage selector)
Check that the voltage selector on the rear panel of the
receiver is set to the local power supply voltage. If
not, set the selector to the correct position using a
screwdriver before connecting the AC power cord to a
wall outlet.
Connecting the AC power cord
Connect the AC power cord from this receiver and
from your audio/video components to a wall outlet.
If you connect other audio components to AC OUTLET
on the receiver, the receiver can supply power to the
connected component(s) so you can turn on/off whole
system when you turn on/off the receiver. Note that
only one switched AC outlet is supplied with the
Australian model.
ANTENNA TV / DBS LD / DVD VIDEO 2
S VIDEO S VIDEO S VIDEO S VIDEO
LD
IN IN OUT IN
DVD
AC-3 RF IN
LD
DVD
COAXIAL IN
FM
VIDEO VIDEO VIDEO VIDEO
75Ω
IN IN OUT IN
COAXIAL
LD
DVD
OPTICAL IN
AM
AUDIO AUDIO AUDIO AUDIO
TV
IN IN OUT IN
DBS
OPTICAL IN
y
CD
OPTICAL IN
DAT
MD
PHONO CD DAT / MD
OPTICAL IN y
DAT
L
MD
OPTICAL OUT
SIGNAL
GND
R
DIGITAL
IN IN REC OUT IN
Caution
Make sure that the total power consumption of the
component(s) connected to receiver's AC OUTLET does not
exceed the wattage stated on the rear panel. Do not connect
high-wattage electrical home appliances such as electric
irons, fans, or TVs to this outlet.
12
VOLTAGE SELECT
220V
240V
120V
VIDEO 1 MONITOR
S-LINK
FRONT SPEAKERS
S VIDEO S VIDEO S VIDEO
CTRL A1 IMPEDANCE USE 4–16 Ω
OUT IN OUT
IN
B A
R L R L
+
VIDEO VIDEO OUT IMPEDANCE
OUT IN SELECTOR
4 Ω 8 Ω –
AUDIO AUDIO
OUT IN
L
R CENTER SPEAKER REAR SPEAKERS
R L
PRE OUT
TAPE
FRONT REAR
CENTER +
L L
WOOFER
R R
–
REC OUT IN
IMPEDANCE USE 4–16 Ω IMPEDANCE USE 4–16 Ω

Before You Use Your Receiver

Before you start using your receiver, make sure that
you have:
• Turned MASTER VOL to the leftmost position (0).
• Selected the appropriate speaker system. (For
details, see "Selecting the speaker system" on
page 9.)
• Set BALANCE to the center position.
Turn on the receiver and check the following indicator.
• Press MUTING on the remote if "MUTING" appears
in the display.
Clearing the receiver's memory
Before you use your receiver for the first time or
when you want to clear the receiver's memory, do
the procedure below.
POWER
POWER
SPEAKERS
A
OFF B
A + B
PHONES
AC OUTLET
AC OUTLET
+ AC 120V 60Hz 1
SWITCHED 120W / 1A MAX
Turn off the receiver.
–
2
Press down DISPLAY, PANEL UP/DOWN,
+
and POWER simultaneously.
–
The contents of the memory (preset station
b
and other parameter settings) are erased.
to a wall
outlet
PANEL UP/DOWN
DISPLAY
VIDEO 1 VIDEO 2 VIDEO 3 LD/DVD TV/DBS TAPE DAT/MD CD
S-VIDEO VIDEO L AUDIO R VIDEO 3 {MEMORY} FM MODE TUNING EQUALIZER DPC
INPUT – + MODE
BAND CH
B
PRESET TUNING
– +
SHIFT FM/AM
SOUND FIELD
DIRECT
PASS
DISPLAY
MUTING
MASTER VOL
SUR
PANEL
EQ
UP/DOWN
INDEX
TUNER PHONO
SET UP BALANCE
•
b
0 10
L R
MODE FUNCTION
GENRE MODE
BASS INPUT
BOOST MODE