Advertisement
r-------------GUARANTEE
CRAFTSMAN PORTABLE ELECTRIC TOOLS ARE UNCONDITIONALLY
ONE YEAR TO GIVE COMPLETE SATISFACTION OR RETURN FOR FREE REPLACEMENT.
THIS GUARANTEE SERVICE IS AVAILABLE BY SIMPLY RETURNING THE TOOL TO ANY
SEARS STORE.
.
introduction
DOUBLE INSULATION
Double Insulation
is a concept in safety, replacing
the standard
grounded supply system,
power tools. The construction
tool affords
compatible
grounded
tool without
grounded conductor,
The double insulation system
eliminates the need for the usual three wire ground-
ed power cord and grounded cupply system. Wher-
ever there is electric current
two complete sets of insulation to protect the user.
All exposed metal parts ore isolated from the in-
ternol metal motor components
sulation.
The lead wires, switch, etc. with their
VARIABLE SPEED
Electronic trigger
control
speed and higher torque
pressure. The speed of your sow is controlled by the
- amount of switch trigger depres.sion; T-..igger switch
is double pole for added sofety and has sofety re-
lease for added utility. Trigger depression
gages .locking mechanism,.
The following guidelines
mining correct speed for various applications:
speed is ideal for starting
as well as other applications
and power is required. MEDIUM speed is suitable
RULES FOR SAFE OPERATION
I.. KNOW YOUR POWER TOOL -
poll'nUal hazards peculiar to this tool.
2.
GROUND ALL TOOLS -
inlo a thn'l'.hole
electrical
attach.'d to a known ground.
:1
KEEP GUARDS IN PLACE and in working order.
4.
KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
5.
AVOID DANGEROUS
6.
KEEP "cHILDREN AWAY, All visitors should bl' kept safe distance from work area.
7.
STORE IDLE TOOLS, When not in use, tools should be stored in dry, high or locked-up place-out
8.
DON'T FORCE TOOL. It will do the job bl'tter and safer at the rate for which it was designed.
9.
USE RIGHT TOOL. Don't forcl' small tool or attachment
WEAR PROPER APPAREL.
10.
rl'comm.'ndl'd
whl'n working outdoors.
II.
USE SAFETY
GLASSES with most tools. Also face or dust mask if cutting operation is dusty.
12.
DON'T ABUSE CORD, Nl'\'l'r carry tool by cord or yank it to disconnect from receptacle. Keep cord from heat, oil and sharp
edges.
13.
SECURE WORK. Usc clamps or a vise to hold work. It's safer than using your hand and it frees both hands to operate tool.
14.
DON'T OVERREACH. Kl'l'p proper footing and balance at all times.
15.
MAINTAIN TOOLS WITH CARE. Keep tools sharp at all times. and clean for best and safest performance.
lions for lubricating
16.
DISCONNECT TOOLS. Whl'n not in use, before sen'icing;
17.
REMOVE ADJUSTING
ed from tool bdore
18.
AVOID ACCIDENTAL STARTING. Don't carry plugged.in tOol with finger on switch.
COPYRIGHT.
1969.
SEARS, ROEBUCK AND CO. and SIMPSONS-SEARS LTD.
in electric
of a double insulated
protection
to a properly
the necessity
for using a
in the tool there are
with protecting
switch delivers
higher
with
increased
trigger
disen-
may be used in deter-
LOW
cuts, sawing ceramics,
where minimum speed
Rl'ad owner's manual carefully, Learn its applications and limitations as well as the specific
UNLESS DOUBLE-INSULATED.
receptacle.
If adapter
is used to accommodate
<Usually the screw securing receptacle
ENVIRONMENT.
Don't use power tool in damp or wet locations. And keep work area well lit.
No loose clothing or jewelry to get caught in moving parts. Rubber gloves and footwear are
and changing accessories.
KEYS AND WRENCHES,
Form habit of checking to see that keys and adjusting wrenches are remov-
turl11ng it on.
BY
POWER
TOOL
INSTITUTE.
INC
-------------~
functional
insulation have the added protection of
non-conductive
sleeving or housings to complete the
double insulation system.
SERVICING OF A TOOL WITH DOUBLE INSULA-
TION REQUIRES EXTREME CARE AND KNOWL.
EDGE OF THE SYSTEM AND SHOULD BE PER-
FORMED ONLY BY A QUALIFIED SERVICE TECH-
NICIAN.
FOR SERVICE WE SUGGEST YOU RE-
TURN THE TOOL TO YOUR NEAREST SEARS
STORE FOR REPAIR WHICH
in.
WITH
ORIGINAL
PARTS.
for sawing ferrous metals, plastics and laminates.
HIGH speed produces best results in sawing wood
and n.on-ferrous metals such as aluminum
requfre high speeds and maximum power.
AVOID RUNNING AT SLOW SPEEDS FOR EX-
TENDED PERIOD OF TIME WHEN POSSIBLE. AT
SLOWER SPEEDS UNDER CONSTANT PROLONG-
ED USAGE, THE UNIT MAY BECOME OVERHEAT-
ED. SHOULD THIS OCCUR: RUN TOOL WITH NO
LOAD AT MAXIMUM
UNIT. THIS WILL ACCELERATE COOLING PRO.
CESS.
~
If tool is equipped
with three-prong
two-prong receptacle,
cover plate). Never remove third prong,
10 do the job of a heavy duty tool.
when changing attachments.
ALL
RIGHTS
RESERVED
Page 2
GUARANTEED FOR
WILL BE DONE
FACTORY
REPLACEMENT
SPEED TO COOL THE
plug, it should be plugged
the adapter wire must be
of reach of children.
Follow instruc-
blades, bits, cutters,
etc.
which
Advertisement
