Hitachi Compute Blade 2000 User Manual page 606

If you enter N in the switch module setting menu and press Enter, you are asked to
select a switch module. At the prompt, enter the slot number of a switch module, and
the current network setting of the specified switch module is displayed. Enter the
network setting of the specified switch module, press Enter, and go to the next setting.
When you set the Ext setting to Int or LOSW, the other settings of the switch module
are automatically filled in.
When you set the Ext setting to Ext and the Synchronize setting to No, the other
settings of the switch module are automatically filled in.
When you set the Ext setting to Ext, the Synchronize setting to Yes, and IP address to
0.0.0.0, the other settings of the switch module are automatically filled in.
Enter the connection setting to the specified switch module, and the changed setting
value is displayed. A message to confirm the change is displayed and the prompt is
ready. Enter Y and press Enter, and the network setting is saved. To cancel the setting
change, enter N and press Enter or just press Enter.
(A,N,S,W,[Q]) : N
(A,N,S,W,[Q]) : N
Select switch module (0-5,[Q=Quit]) : 0
Select switch module (0-5,[Q=Quit]) : 0
Ext setting : Int
Ext setting : Int
(0=Int,1=Ext,2=IOSW,[Unchange]) : 1
(0=Int,1=Ext,2=IOSW,[Unchange]) : 1
Synchronize : No
Synchronize : No
(0=No,1=Yes,[Unchange]) : 1
(0=No,1=Yes,[Unchange]) : 1
IP address : 0.
IP address : 0.
([Unchange]) : 192.168.1.111
([Unchange]) : 192.168.1.111
Subnetmask : 0.
Subnetmask : 0.
([Unchange]) : 255.255.255.0
([Unchange]) : 255.255.255.0
Default gateway : 0.
Default gateway : 0.
([Unchange]) : 192.168.1.128
([Unchange]) : 192.168.1.128
-- Switch module network setting --
-- Switch module network setting --
SW Ext IP address
SW Ext IP address
-- ---- ---------------- --------------- --------------- -------- -----------
-- ---- ---------------- --------------- --------------- -------- -----------
0 Ext 192.168. 1.111
0 Ext 192.168. 1.111
1 Int --------------
1 Int --------------
2 Int --------------
2 Int --------------
3 Int --------------
3 Int --------------
4 Int --------------
4 Int --------------
5 Int --------------
5 Int --------------
WARNING : Session may be disconnected when setting saved.
WARNING : Session may be disconnected when setting saved.
Confirm? (Y,[N]) : Y
Confirm? (Y,[N]) : Y
- <Switch module0> Writing setting was completed.
- <Switch module0> Writing setting was completed.
Hit enter key. (Enter)
Hit enter key. (Enter)
When Network OS version 3.0.0 is on a Brocade 10 Gb DCB
switch module, the default gateway setting from the
management module does not take effect on the switch
module. Log in to the switch module and configure it using
the ip route command. See the Network OS Administrator's
Guide for details. If Network OS version 2.0.1 is on the switch
module, you cannot configure the gateway.
0. 0. 0
0. 0. 0
0. 0. 0
0. 0. 0
0. 0. 0
0. 0. 0
Subnetmask Default gateway Ext port Synchronize
Subnetmask Default gateway Ext port Synchronize
255.255.255. 0 192.168.
255.255.255. 0 192.168.
------------- -------------
------------- -------------
------------- -------------
------------- -------------
------------- -------------
------------- -------------
------------- -------------
------------- -------------
------------- -------------
------------- -------------
555
1.128 MGMT-0 Yes
1.128 MGMT-0 Yes
------ ---------
------ ---------
------ ---------
------ ---------
------ ---------
------ ---------
------ ---------
------ ---------
------ ---------
------ ---------