18. SERVICING - Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. For service warranty information call the NHT Hotline number: 1-800-NHT-9993.
NHT dealer or our Toll-Free Customer Service Hotline at: Please retain the SubOne i packaging to protect the system in the event that you move or transport it. 1-800-NHT 9993...
NHT products are designed to deliver refined, musical sound from attractive and affordable packages. Our efforts are guided by the study of human hearing and are optimized for real-world use. Every NHT product undergoes rigorous testing and quality control at the factory to ensure you years of listening pleasure.
(17) High Level Input - Barrier strip for speaker-level input from receiver / amplifier. (18) Subwoofer Gain Selector - Allows optional attenuation of SubOne i gain. (19) High Pass Filter - 3-way selectable high pass crossover for satellite line out.
(such as in two corners), as it will tend to exaggertate standing waves. As the SubOne i is not shielded, do not place it in close proximity to a television, or picture discoloration will occur. The SubOne i Controller is most conveniently placed in a rack with other equipment, although it may also be placed on top of the subwoofer.
Turn down the volume control on the SubOne i Controller to its lowest position (counter-clockwise). Turn on your audio system, including the SubOne i. Play some music you are familiar with and set your receiver/pre- amplifier volume to a comfortable listening level. Slowly increase the volume on the SubOne i Controller, lis- tening for proper frequency balance.
Page 8
The Flat / Video Contour switch allows you the best of both worlds. In the “Flat” mode, the SubOne i’s response is flat for accurate musical reproduction. In the “Video Contour” mode, the SubOne i has boosted output between 40Hz and the low pass frequency, and rolls off response below 35Hz to provide greater power han- dling at elevated listening levels.
Page 9
The SubOne i has a STANDBY MODE feature that is automatic and requires no user adjustment. When no signal is present for 45 minutes, the SubOne i goes into Standby Mode, and it will use a minimum of power to remain “asleep.”...
1) Your L & R speakers are connected directly from your amplifier / receiver. 2a) If you have a receiver with “Pre-Out” and “Main-In” jacks, patch in the SubOne i Controller between these. With an RCA intercon- nect cable, connect the receiver’s “Pre-Out” to the SubOne i Controller’s LINE IN. Connect a second RCA interconnect cable from the SubOne i Controller’s SATELLITE LINE OUT back to the receiver’s “Main-In.”...
1) Your L & R speakers are connected directly from your amplifier / receiver. 2a) If you have a receiver with “Pre-Out” (or “Line Out”) jacks but no “Main-In,” you may connect the SubOne i Controller from the “Pre- Out” without having to route the signal back into the receiver. Using an RCA interconnect cable, connect the “Pre-Out” to the SubOne i Controller’s LINE IN.
This method of connection is recommended if you have a receiver with no line level preamplifier output of any sort and you want your L & R speakers to receive a high-pass filtered signal. The SubOne i Controller may be connected to the system at speaker level between the receiver and the speakers.
SubOne i Controller in parallel from the same terminal. Connect one pair of speaker cables from the receiver’s speaker output ter- minal to the L & R speakers. Connect a second pair of speaker cables from the receiver’s same output terminal to the SubOne i Controller’s INPUT FROM AMPLIFIER barrier strip.
Listen to your system and make adjustments to achieve a seamless blend between your main speakers and the SubOne i. Four common problems are outlined below. Follow the flow chart to correct these. See the glos- sary for any terms you are unfamiliar with.
! ! Operation When the SubOne i is turned on, there will be an audible “pop.” Do not be alarmed! This is inherent to the amplifier design and will not damage the subwoofer or your audio system. We do recommend, however, that the SubOne i’s power is left “on”...
Line-Level Connection: Low level RCA/phono type connection. Load: A term used to describe the impedance which a speaker presents to an amplifier. Low-Pass Filter: A filter that passes only frequencies below a certain upper limit; electronically removes high frequencies from a full range signal.