Nikon D700 Repair Manual
  1. Manuals
  2. Brands
  3. Nikon Manuals
  4. Digital Camera
  5. D700
  6. Repair manual

Nikon D700 Repair Manual

Hide thumbs Also See for D700:
Table of Contents

Advertisement

Quick Links

See also: User Manual , Quick Manual
Printed in Japan JULY 2008
logo_Q0610_forGraphic
VBA22001
080221_Gdesign_ito
REPAIR MANUAL
VBA22001-R.3754.A
作成承認印
Copyright ｃ 2008 by Nikon Corporation.
All Rights Reserved.
無断転載を禁ず !!
INC
配布許可印
サービス
計画課
Ｍ

Advertisement

Table of Contents
loading

Related Manuals for Nikon D700

Summary of Contents for Nikon D700

  • Page 1 VBA22001-R.3754.A 作成承認印 配布許可印 サービス 計画課 Ｍ logo_Q0610_forGraphic VBA22001 080221_Gdesign_ito REPAIR MANUAL Copyright ｃ 2008 by Nikon Corporation. All Rights Reserved. 無断転載を禁ず !! Printed in Japan JULY 2008...

  • Page 2: Table Of Contents

    AF-assist lamp ･･･････････････････････････････････････････････････････････････････････ Ｄ 51 Grip-support mold ･･････････････････････････････････････････････････････ Ｄ 52 Separation of Front body from Rear body 4.Separation of Prism box unit from Front body unit ････････････････････････････････････････････････ Ｄ 55 Separation of Prism box unit from Front body unit - D700-...
  • Page 3 ･ ･････････････････････････････････････････････････････････････････････ Ｄ 92 Battery contact mold ･ ････････････････････････････････････････････････････････････････････ Ｄ 93 Rear body accessories Assembly / Adjustment 1.Rear body Rear body accessories ･････････････････････････････････････････････････････････････････････････････ Ａ 1 Battery contact mold ･･････････････････････････････････････････････････････････････････････････････ Ａ 2 Grip unit ････････････････････････････････････････････････････････････････････････････････････････ Ａ 4 Power base unit ･･････････････････････････････････････････････････････････････････････････････････ Ａ 5 - D700-...
  • Page 4 5. Mounting of Front body on Rear body Mounting of front body on rear body ･････････････････････････････････････････････････････････････････ Ａ 47 Inspection and Adjustment of Body back ･････････････････････････････････････････････････････････････ Ａ 50 Grip-support mold ･･･････････････････････････････････････････････････････････････････････････････ Ａ 52 AF-assist lamp ･･････････････････････････････････････････････････････････････････････････････････ Ａ 53 Main-PCB ･･････････････････････････････････････････････････････････････････････････････････････ Ａ 53 - D700-...
  • Page 5 DG shield plate unit ･･････････････････････････････････････････････････････････････････････････････ Ａ 99 I/F cover ･･･････････････････････････････････････････････････････････････････････････････････････ Ａ 99 How to connect camra and PC ･････････････････････････････････････････････････････････････････････ Ａ 101 D700 Inspection and Adjustment Software ･･･････････････････････････････････････････････････････････ Ａ 102 Procedure for installing USB driver ･････････････････････････････････････････････････････････････････ Ａ 106 AE inspection and adjustment ･････････････････････････････････････････････････････････････････････ Ａ 108 AF inspection and adjustment ･････････････････････････････････････････････････････････････････････...
  • Page 6 Setting of two-dimensional barcode reader ･･････････････････････････････････････････････････････････････ Ａ 129 Imageing unit adjustment ････････････････････････････････････････････････････････････････････････････ Ａ 132 ∞ Infinity focus inspection & adjustment ･･･････････････････････････････････････････････････････････････ Ａ 138 D700 Tilted sensor checking chart ･････････････････････････････････････････････････････････････････････ Ａ 139 ･･･････････････････････････････････････････････････････････････････････････････････ Ｅ 1 ～Ｅ 2 Wiring ････････････････････････････････････････････････････････････････････････ Ｅ 3 ～Ｅ 15 Mounting Drawing ････････････････････････････････････････････････････････････････････････...

  • Page 7: Points To Notice For Disassembly And Assembly

    　・ Do NOT mix up lead-free solder with traditional solder. Caution: When "Separation of Front body from Rear body", "Disassembly of Image sensor unit" and "Disassembly of Bayonet" are performed, be sure to carry out "RESET AF-DEFOCUS COMPENSATION" of the D700 adjustment software after assembly. - D1 ･ D700 -...

  • Page 8: External Area And Image-Related Pcb/Base Plate

    Rubber cap (#68) Rear rubber unit (#B447) ・ Remove the rear rubber unit (#B447) from the back. ・ Remove the I/F rubber unit (#B10061). I/F rubber unit (#B10061) Double-stick tape ( #546) I/F rubber unit (#B10061) Tape [#TA-0004 (4.4×4.4)] - D2 ･ D700 -...
  • Page 9 VBA22001-R.3754.A ・ Take out the screw (#1647). Screw (#1647) ・ Remove the grip rubber unit (#B60). Grip rubber unit (#B60) double stick tape (#945) double stick tape (#946) Grip rubber unit (#B60) double stick tape(#947) - D3 ･ D700 -...

  • Page 10: Battery Lid

    Caution: Remove [#B801] sideways so as not to break the shaft. Battery lid unit (#B801) Bottom cover ・ Take out the screw (#1509). Screw (#1509) ・ Take out the screw (#1509). ・ Remove the DOUBLE STICK TAPE (#883) DOUBLE STICK TAPE (#883) Screw (#1509) - D4 ･ D700 -...
  • Page 11 ・ Take out the three screws (#1517). Screw (#1517)×3 Screw (#1529)×2 Screw (#1528)×2 Battery-lid hinge cover Hinge mold (#806) Screw (#1571)×2 (#807) Tripod Socket (#25) Sponge (#983) Sponge (#989) Sponge (#982) Screw (#1519)×4 Sponge (#984)×2 Sponge (#981) Bottom cover (#27) - D5 ･ D700 -...

  • Page 12: Removal Of Back Cover

    Caution: In case the length of the screw is different between ① and ② , use the longer one for ① . Screw (#1545)×2 ・ Take out the screw (#1551). Screw (#1551) - D6 ･ D700 - Changed page △× 1 August.19,2008...
  • Page 13 VBA22001-R.3754.A ・Remove the back cover. ・ Remove the FPC at three places. - D7 ･ D700 -...
  • Page 14 VBA22001-R.3754.A ・ Take out the two screws (#1518). Screw (#1518)×2 ・ Remove the CF cover unit (#B441) from the back cover unit (#B421RP). Back cover unit (#B421RP) CF cover unit (#B441) - D8 ･ D700 -...

  • Page 15: Back Cover Unit /Cf Cover Unit

    Back cover unit / CF cover unit #985 #986 #962 #468 #987 #455 #961 #963 #924 #476 #421 #484 #1593×3 #475 #426 #B469 #B478 #925 #1630 #485 #457 #1542×2 #458 #1560×5 #B467 #456 #470 #B5020 #1589×3 #422 - D9 ･ D700 -...
  • Page 16 VBA22001-R.3754.A #431 #433 #434×2 #435×2 #5057 #955 #429 #432 #425 #1626×3 C/F COVER UNIT #B441 C/F LID UNIT#B423 #445 Take out the screw, and remove the retainer plate of the shaft. - D10 ･ D700 -...

  • Page 17: I/F Cover

    VBA22001-R.3754.A I/F cover ・ Take out the two screws (#1510). ・ Remove the I/F cover (#28). I/F cover (#28) Screw (#1510)×2 I/F cover (#28) Sponge (#969) Screw (#1642)×2 I/F lid (#392) Sponge (#975) Mold (#395) - D11 ･ D700 -...

  • Page 18: Discharge Of Main Condenser

    ・ Discharge the main condenser (#5067). Be careful NOT to touch the body during discharging. 2KΩ/5W Main condenser (#5067) DG shield plate unit ・ Take out the five screws (#1521), and remove the shield plate unit (#B683). Shield plate unit (#B683) - D12 ･ D700 -...

  • Page 19: Dg-Pcb

    VBA22001-R.3754.A DG-PCB ・ Remove the FPC. ・ Disconnect the connector at two places. Connector Connector ・ Remove the FPC at four places. ・ Disconnect the connector at two places. Connector Connector - D13 ･ D700 -...
  • Page 20 Sheet (#816) Tape (#815) Rubber (#814) ・ Unsolder the wires {[Red (thick)][Black (thick)][Brown]}. Wire [Brown] Wire [Red (thick)] Wire [Black (thick)] ・ Unsolder the wires ([Red (thin)][Black (thin)][Orange]). Wire [Red (thin)] Wire [Black (thin)] Wire [Orange] - D14 ･ D700 -...
  • Page 21 VBA22001-R.3754.A ・ Take out the screw (#1521), and remove the DG-PCB unit (#B5017RP). DG-PCB unit (#B5017RP) Screw (#1521) Gasket (#693) DG-PCB unit (#B5017RP) - D15 ･ D700 -...

  • Page 22: Image Sensor Unit

    Image sensor unit ・Remove the harness (#5073) from the image sensor unit (#B20521). ・ Peel off the tape [#TA-0005 (5×15)]. Harness (#5073) Tape (#TA-0005) Connector Image sensor unit (#B20521) ・ Take out the three screws (#525). Screw (#525) - D16 ･ D700 -...

  • Page 23: Cf-Pcb

    T=0.1 Washer Washer(#531) Harness (#5072) Washer CF-PCB ・ Position the lever of the CF-PCB (#5018) toward the direction of the arrow, and take out the three screws (#1543). Screw (#1543) CF-PCB (#5018) - D17 ･ D700 - Changed page (Overall revision) August.19,2008...
  • Page 24 VBA22001-R.3754.A ・ Remove the CF-PCB (#5018) from the body. CF-PCB (#5018) ・ Remove the connection-FPC (#5038) from the CF-PCB (#5018). Connection-FPC (#5038) CF-PCB (#5018) - D18 ･ D700 -...

  • Page 25: Diopter Adjustment Knob

    VBA22001-R.3754.A Diopter adjustment knob ・ Remove the Cover (#1130). Cover (#1130) Double-stick tape (#1154) Cover (#1130) ・ Take out the screw (#1552). ・ Remove the diopter adjustment knob (#1121). Diopter adjustment knob (#1121) Screw (#1552) - D19 ･ D700 -...

  • Page 26: Eyepiece

    Eyepiece cover (#1137) Sponge (#1204) Sponge (#1202) Eyepiece stopper (#1150) Eyepiece shutter base (#B1141) Eyepiece shutter (#1145) Pin (#1152) Sponge (#1201) Eyepiece shutter (#1144) Washer (#1147) Screw (#1146) Spring (#1151) E-ring (#1652) Screw (#1542) Lug plate (#1206) - D20 ･ D700 -...

  • Page 27: Removal Of Top Cover

    Plastic plate By using a plastic plate, peel off the double-stick tape. Insert another plastic plate from the opposite side, and pull out the condenser by kind of scooping it up. Pull out parallel to the bottom. - D21 ･ D700 -...
  • Page 28 VBA22001-R.3754.A ・ Unsolder the wires ([Green][Brown]). wire[Brown] wire[Green] ・ Take out the two screws (#1512). Screw (#1512) Screw (#1512) - D22 ･ D700 -...
  • Page 29 VBA22001-R.3754.A ・ Take out the two screws (#1511). ・ Take out the screw (#1512). Screw (#1512) Screw (#1511)×2 ・ Take out the two screws (#1509). Screw (#1509)×2 - D23 ･ D700 -...
  • Page 30 VBA22001-R.3754.A ・ Press the SB pop-up button (#40), and raise the SB (speed light). SB pop-up button (#40) ・ Take out the two screws (#1548). Screw (#1548)×2 - D24 ･ D700 -...
  • Page 31 VBA22001-R.3754.A ・ Position the top cover as below, and disconnect the FPC from the connector. ・ Remove the top cover. - D25 ･ D700 -...

  • Page 32: Top Cover

    ・ Unsolder the wires ([Black][Red]) of the main condenser (#5067). Wire [Black] Wire [Red] 　 CD unit ・ Peel off the tape [#TA-0005 (10×20)]. ・ Unsolder the top cover-FPC (#5003) and release sw FPC (#5033). #TA-0005 Release sw FPC (#5033) Top cover-FPC (#5003) - D26 ･ D700 -...
  • Page 33 ・ Take out the two screws (#1571), and remove the rear-CD unit (#B726). ・ Take out the two screws (#1544), and remove the (#B725). Sub Command Dial Unit (#B725) Sub Command Dial Unit (#951) Sponge (#B725) Sub Command Dial Unit Screw (#1544) (#B726) Rear-CD unit (#920) Sponge Screw (#1571) - D27 ･ D700 -...

  • Page 34: Sb-Pcb Unit

    ・ Peel off the tape (#929) from the two places. ・ Remove the wires from the cutout section. Tape (#929) Cutout ・ Unsolder the wires ([Black][Red][Yellow]) of the metering mode-FPC. Wires ([Black][Red][Yellow]) ・ Peel off the tape (#929). Tape (#929) - D28 ･ D700 -...

  • Page 35: Release-Sw

    ・ Take out the two screws (#1541), and remove the SB-PCB unit (#5013). [Yellow] Screw (#1541) SB-PCB unit (#5013) Screw (#1541) [Green][Black][Orange][Gray][Blue] [Red] Release-SW ・ Peel offf the tape (#949). ・ Take out the screw (#1605). Tape (#949) Screw (#1605) - D29 ･ D700 -...
  • Page 36 ・Take out the two screws (#796), and remove the two SB pop-up arms (#322). ・ Take out the two screws (#1623), and remove the SB upper cover (#301). Screw (#1623) SB pop-up arm (#322) SB upper cover (#301) SB pop-up arm (#322) Screw (#796) Screw (#796) - D30 ･ D700 -...
  • Page 37 VBA22001-R.3754.A ・ Take out the screw (#1601). ・ Pull the wires outside. ・ Take out the screw (#1601) and remove the spring (#305), [using caution to avoid popping out of the spring.] Spring (#305) Screw (#1601) - D31 ･ D700 -...
  • Page 38 ・Remove the collar (#B306), (using caution to avoid bending the brush). Collar (#B306) ・ Remove the collar (#308). ・ Remove the collar (#307). ・ Remove the SB lower case unit (#B302). Collar (#307) Collar (#308) SB lower case unit (#B302) - D32 ･ D700 -...

  • Page 39: Top Cover Fpc Unit

    ・ Unsolder at four places. Unsolder here. Screw (#321) Screw (#321) Unsolder here. ・ Remove the shoe mold unit (#B317), hot shoe (#316) and hot shoe spring (#318). Hot shoe spring (#318) Hot shoe (#316) Shoe mold unit (#B317) - D33 ･ D700 -...
  • Page 40 ・ Take out the screw (#1606) and remove the spring (#750), (using caution to avoid popping out of the spring.) ・ Peel off the top cover-FPC (#5003) from the support plate (#731). Screw (#1606) Spring (#750) Support plate (#731) Top cover-FPC (#5003) - D34 ･ D700 -...
  • Page 41 Screw (#1560) SUPPORT PLATE (#731) Screw (#1540) ・ Take out the three screws (#1544). ・ Take out the two screws (#1549). Screw (#1549) Screw (#1544) ・ Remove the top cover-FPC (#5003). Top Cover Unit(#B23RP) Top cover-FPC (#5003) - D35 ･ D700 -...

  • Page 42: Main Sw

    SW (#39) Tape (#929) Top cover-FPC (#5003) Double-stick tape (#753) Double-stick tape (#913) Power Plate (#747) Double-stick Mold(#703) tape (#912) Spring (#746) Sponge(#965) Screw (#1537)×2 Tape (#929) Main SW ・ Remove the conducting button (#787). Conducting button (#787) - D36 ･ D700 -...
  • Page 43 ・ Remove the metering mode dial unit (inside) (#B782), AE mode dial (#781), and AE-lock button (#780). ・ Remove the spring (#784), (using caution to avoid popping out of it). Screw (#1648) Metering mode dial unit (inside) (#B782) Spring (#784) AE mode dial (#781) AE-lock button (#780) - D37 ･ D700 -...
  • Page 44 ・ Take out the screw (#1608), and remove the two ON-OFF SW brushes (#748). ON-OFF SW brush (#748) ・ Remove the E-ring (#1652), and then the Washer (#744), (using caution to avoid popping out of the washer). (#1652) E-ring (#744) Washer - D38 ･ D700 -...
  • Page 45 ・ Take out the screw (#1565), and remove the Plate (#312). ・ Remove the spring (#310), (using caution to avoid popping out of it). ・ Remove the SB Lock Lever(#309) Screw (#1565) SB Lock Lever (#309) Retainer plate (#312) Spring (#310) - D39 ･ D700 -...

  • Page 46: Mode Dial

    VBA22001-R.3754.A Mode dial ・ Unsolder the mode dial FPC (#5025) and trefoil FPC (#5026). Trefoil FPC Mode dial FPC (#5026) (#5025) ・ Take out the screw (#1574). s crew#1574 - D40 ･ D700 -...
  • Page 47 ･ Take out the screw (#1571) and the two screws (#1609), and remove the base plate (#505). Screw (#1571) base plate (#505) Screw (#1609) ×2 Mode dial FPC (#5025) Double-stick tape (#514) Double-stick tape (#515) Base plate (#505) - D41 ･ D700 -...

  • Page 48: Top Cover External Parts

    ・ Remove the Conducting Button (#513). Conducting Button (#513) ・Take out the screw (#1532), and remove the sync terminal (#50). Screw (#1532) Sync terminal (#50) ・ Remove the super X around the mold (#510). Mold (#510) Super X - D42 ･ D700 -...
  • Page 49 ・ Remove the tape (#972). Tape (#972) ・ Peel off the tape (#709). ・ Remove the super X from the AF-assist lamp protector (#327). ・ Remove the AF-assist lamp protector (#327). Super X Tape (#709) AF-assist lamp protector (#327) - D43 ･ D700 -...
  • Page 50 VBA22001-R.3754.A #701 #702 #B44 #788 #967 #B43 #994 #970 Super X #968 #967 #1659 Super X #993 #1659 #966 #765×2 #766×2 - D44 ･ D700 -...

  • Page 51: Separation Of Front Body From Rear Body

    VBA22001-R.3754.A 3. Separation of Front body from Rear body DC/DC PCB ・ Peel off the tape [#TA-0005 (10×3.7)]. Tape (#TA-0005) DCDC PCB IF PCB ・ Unsolder the wires ([Gray][Orange][Red]). Wire [Red] Wire [Orange] Wire [Gray] - D45 ･ D700 -...
  • Page 52 Wire [Brown] Wire [Green] Wire [Blue charge motor] Wire [Red charge motor] Wire [Blue] Wire [Brown] ・ Take out the four screws (#1509). ・ Remove the DC/DC PCB (#5047). Screw (#1509) ×2 Screw (#1509) ×2 DC/DC PCB (#5047) - D46 ･ D700 -...

  • Page 53: Main-Pcb

    ・ Unsolder the wire [Blue] of the battery contact unit (#B822). ・ Pull this wire[Blue] of the battery contact unit (#B822) out from the gap between the main PCB and the body. FPC of Lens contact FPC unit (#B5008) Wire [Blue] - D47 ･ D700 -...
  • Page 54 ・ Peel off the tape [#TA-0005 (10×3.7)]. Penta-FPC unit (#B5005) Connector Tape (#TA-0005) ・ Unsolder the eight wires. ・ Disconnect the FPC at three places. Wire [Yellow] Wire [Black AF-assist lamp]×2 Wire [Gray] Wire [Black buzzer]×2 Wire [Blue] Wire [Orange] - D48 ･ D700 -...
  • Page 55 VBA22001-R.3754.A ・ Peel off the tape [#TA-0005 (10×20)] by half, and remove the wires ([Black][Red). Tape (#TA-0005) ・ Take out the two screws (#1616). Screw (#1616)×2 ・ Remove the main PCB (#5001). Main PCB (#5001) - D49 ･ D700 -...
  • Page 56 VBA22001-R.3754.A ・ Remove the Connection-FPC (#5039). Connection-FPC (#5039) ・ Unsolder the wires ([Black][Red]). Main PCB (#5001) Wire [Black] Wire [Red] ・ Remove the Lug plate (#775). Lug plate (#775) - D50 ･ D700 -...

  • Page 57: Af-Assist Lamp

    Screw (#1638) Sponge (#325) Grip-support mold ・ Take out the screw (#1644). Screw (#1644) ・ Remove the grip-support mold (#58). ・ Remove the sponge (#952) from the grip-suport mold (#58). Sponge (#952) Grip-support mold (#58) Grip-support mold (#58) - D51 ･ D700 -...

  • Page 58: Separation Of Front Body From Rear Body

    ・ Unsolder at four places, and pull out the FPC-end of the shutter unit (#B12001) through the hole of the penta FPC unit (#B5005). Penta FPC unit (#B5005) TAPE #TA-0005（10 × 20） Shutter unit (#B12001) ・ Take out the screw (#1525). Screw (#1525) Changed page (Overall revision) - D52 ･ D700 - October.02.2008...
  • Page 59 VBA22001-R.3754.A ・ Take out the five screws (#1575). ・ Take out the four screws (#1531). Screw (#1531)×2 Screw (#1531)×2 - D53 ･ D700 -...
  • Page 60 VBA22001-R.3754.A ・ Remove the front body unit (#B26RP) from the rear body. Front body unit (#B26RP) Rear body - D54 ･ D700 -...
  • Page 61 4. Separation of Prism box unit from Front body unit Separation of Prism box unit from Front body unit ・ Disconnect the FPC from the connector. Penta-FPC unit (#B5005) PD PCB (#5002) ・ Disconnect the FPC from the connector. Penta-FPC unit (#B5005) SI-LCD unit (#B5055) - D55 ･ D700 -...
  • Page 62 ・ Disconnect the FPC from the connector, (using caution with the direction of the connector). Penta-FPC unit (#B5005) Inside finder LCD unit (#B5004) ・ Disconnect the FPC from the connector. SI-LCD unit (#B5055) Lens contact unit (#B5008) ・ Disconnect the FPC from the connector. Metering FPC unit (#B5006) SI-LCD unit (#B5055) - D56 ･ D700 -...
  • Page 63 VBA22001-R.3754.A ・Take out the four screws (#1525). ・Remove the prism box unit (#B1101RP). Prism box unit (#B1101RP) Front body unit (#B26RP) - D57 ･ D700 -...
  • Page 64 ・ Take out the three screws (#1541). Screw (#1541)×3 ・ Remove the metering FPC unit (#B5006). Screw (#1133)×3 Metering FPC unit (#B5006) Metering FPC unit (#B5006) Spring (#1134)×3 Metering FPC base unit (#B1131) Prism box unit (#B1101RP) - D58 ･ D700 -...
  • Page 65 ・Remove the four solders of the penta FPC unit (#B5005). ・ Remove the penta FPC unit (#B5005) from the prism box unit (#B1101RP). Penta FPC unit (#B5005) Prism box unit (#B1101RP) ・ Remove the Spring (#1103) from the prism box unit (#B1101RP). Spring (#1103) Hook - D59 ･ D700 -...
  • Page 66 (#3) Screen (#1180A-C) Washer #1180A-D △（Revision） (#1103) Spring ・ Unhook the Spring (#1103) at both ends from the holes of the prism box unit (#B1101RP). Prism box unit (#B1101RP) (#1103) Spring Changed page △× 2 - D60 ･ D700 - October.02.2008...
  • Page 67 ・ Remove the Springs [(Grip-side; white)(#1215) and (I/F-side; black)(#1112)] by releasing each hook in the numeric order. I/F side ① Grip-side ② ② ① ③ ① ③ ② ③ (#1112) Spring (#1215) Spring (#1196)DOUBLE STICK TAPE (#1195) Rubber (#1111) Penta prism retainer (#1113) Sheet (#B4) Penta Prism Unit - D61 ･ D700 -...
  • Page 68 ・ Remove the Spring (#1127) first, then steel ball (#1136), (using caution to avoid popping out of the spring). (#1127) Spring (#1136) Steel ball ・Take out the two screws (#1595), and remove the Mold (#1123). (#1123) Mold (#1123) Mold Screw (#1595)×2 (#1129)SPONGE - D62 ･ D700 -...
  • Page 69 ・ Remove the Plate (#1120) (by releasing from the two hooks). (#1120) Plate (#1120) plate Hook Hook Screw (#1597)×2 ・ Take out the two screws (#1595). ・ Remove the Eyepiece Lens Unit (#B1119). Screw (#1595)×2 (#B1119) Eyepiece Lens Unit - D63 ･ D700 -...
  • Page 70 (#1122) Diopter Shaft Inside finder LCD unit ・ Remove the inside finder LCD unit (#B5004) by separating the FPC from the boss. Inside finder LCD unit (#B5004) Boss ・ Take out the two screws (#1585). Screw (#1585)×2 - D64 ･ D700 -...
  • Page 71 ・ Remove the two plates (#1185), (using caution because the their edges are inserted into the square holes of the prism box unit.) Square hole Square hole Screw (#1537)×2 (#1185) Plate×2 ・ Remove the lower display prism (#8). (#8) Lower display prism (#8) Lower display prism (#1186) Tape - D65 ･ D700 -...
  • Page 72 ・ Perform the same works on the rear side, too. (#1167) Plate (#1167) Plate ・ Pull and remove the SI guide unit (#B1168), being careful NOT to damage the FPC. (#5011) SI LCD FPC (#B1168) SI guide unit - D66 ･ D700 -...
  • Page 73 ・ Remove the Spacer Frame (#1109). ・ Remove the condenser lens (#19), (being careful NOT to damage it). (#1109) Spacer Frame (#19) Condenser lens ・Remove the finder frame (#1107). (#1107) Finder frame - D67 ･ D700 - Changed page (Overall revision) August.19,2008...
  • Page 74 ・ Remove the Plates (#1163 and #1164)(using caution because the their edges are inserted into the square holes of the prism box unit.) Screw (#1597)×2 (#1164) Plate (#1163) Plate ・ Remove the rubber (#1117) from the lower part of the SI-LCD unit (#B5055). SI-LCD unit (#B5055) (#1117) Rubber - D68 ･ D700 -...
  • Page 75 ・ Pull the SI-LCD unit (#B5055) from the prism box unit (#B1101RP). (#B1101RP) Prism box unit (AorB) (#1115) Rubber △（Revision） (#B5055) SI- LCD unit Be careful NOT to lose the retainer rubber when pulling the SI-LCD unit. - D69 ･ D700 - Changed page △× 1 August.19,2008...
  • Page 76 VBA22001-R.3754.A 6. Front body unit Power drive ・ Pull out the wire [Yellow] of the PD PCB (#5002). ・Peel off the tape [#TA-0005 (10×20)]. Tape (#TA-0005) - D70 ･ D700 -...
  • Page 77 ・ Unsolder the wires of AF motor ([Blue][Yellow]). ・ Take out the two screws (#1663). ・ Remove the PD PCB (#5002). Push the 10-pin FPC (#5010) to the sides.. Screw (#1663)×2 1002-DC/DCFPC (#5042) PCB(#B5002) Wires of AF motor ([Blue][Yellow]) PD PCB (#5002) Wires ([Blue][White][Yellow]) - D71 ･ D700 -...
  • Page 78 VBA22001-R.3754.A AF sensor ・ Remove the connection-FPC (#5042). Boss Connection-FPC (#5042) Connection-FPC (#5042) ・ Disconnect the FPC from the connector. ・ Take out the screw (#1503). Front body unit (#B26RP) AF sensor unit (#B20294) Screw (#1503) Boss - D72 ･ D700 -...
  • Page 79 ・ Take out the two screws (#275) and remove the two washers (#1657). ・ Remove the AF sensor unit (#B20294). Washer (#1657)×2 Screw (#275)×2 AF sensor unit (#B20294) ・ Remove the spring (#273). ・ Remvoe the two springs (#276). Spring (#276) AF sensor base plate (#B10277) Spring (#273) - D73 ･ D700 -...
  • Page 80 ・ Take out the screw (#283). ・ Remove the Spring (#284). Remove from the V-groove. Screw (#283) Spring (#284) ・ Take out the three screws (#1509). ・ Remove the AF sensor base plate (#B10277). Screw (#1509)×3 AF sensor base plate (#B10277) - D74 ･ D700 -...
  • Page 81 VBA22001-R.3754.A Bayonet ・ Take out the screw (#1620) and the four screws (#1621). ・ Remove the bayonet mount (#401). Screw (#1621)×4 Bayonet mount (#401) Screw (#1620) ・ Remove the bayonet mount spring (#402). Bayonet mount spring (#402) - D75 ･ D700 -...
  • Page 82 ・ Take out the screw (#387), and remove the SCM changeover lever (#383). Cover ring (#388) Screw (#387) SCM changeover lever (#383) Cover ring (#388) Double stick-tape (#389) ・ Take out the two screws (#1518) and the three screws (#55). Screw (#55) Screw (#1518)×2 Screw (#55) - D76 ･ D700 -...
  • Page 83 ・Remove the roller (#407). Then remove the spring (#406) by separating from boss and roller. Roller (#407) Spring (#406) Boss ・ Remove the aperture coupling ring unit (#B404RP). ・ Remove the Sponge (#916). ・ Remove the Sponge (#992). Aperture coupling ring unit Sponge (#992) (#B404RP) Sponge (#916) - D77 ･ D700 -...
  • Page 84 SB pop-up button (#40) Sync mode button (#37) Release button ・ Take out the screw (#1516) and the three screws (#66). Screw (#1516) Screw (#66)×3 ・ Remove the release base unit (#B381). Front body unit (#B26RP) Release base unit (#B381) - D78 ･ D700 -...
  • Page 85 ・ Remove the FPCs' solders of the I-base plate unit (#B71) and those of the AF driving base unit (#B10328). I-base plate unit (#B71) AF driving base unit (#B10328) ・ Take out the screw (#1503). ・ Disconnect the FPC from the connector. Front body FPC unit (#B5009) I-base plate unit (#B71) Screw (#1503) - D79 ･ D700 -...
  • Page 86 VBA22001-R.3754.A ・Take out the two screws (#1523), three screws (#1524), and the screw (#1530) as below. Screw (#1524) Screw (#1523) Screw (#1524) Screw (#1530) ・ Remove the mirror box unit. Mirror box unit Front body unit (#B26RP) - D80 ･ D700 -...
  • Page 87 VBA22001-R.3754.A 10-pin FPC ・ Remove the solders of the 10-pin FPC (#5010). 10-pin FPC (#5010) Remove solders here. (#5010) 10-pin FPC (#991)Tape Screw (#1503) (#39) SW Screw (#65) Double-stick tape(#957) (#41) Remote connector - D81 ･ D700 -...
  • Page 88 Coupling shaft (#342) ・ Pull the Coupling shaft (#342) from the shaft hole. Coupling shaft (#342) ･ Take out the two screws (#347). ・ Remove the AF driving base unit (#B10328). Screw (#347)×2 AF driving base unit (#B10328) - D82 ･ D700 -...
  • Page 89 ・ Flick up the front body FPC unit (#B5009), so that the backing plate (#35) can be seen. Then, take out the four screws (#1510). Front body FPC unit (#B5009) Screw (#1510)×4 Backing plate (#35) E-ring (#1652) × 2 Sheet (#934) × 2 Spring (#36) × 2 Preview/Function Button (#33) × 2 - D83 ･ D700 -...
  • Page 90 ・ Take out the screws (#1521 and #1615), and remove the lens contact unit (#B5008). Lens contact unit (#B5008) Screw (#1521) Front body unit (#B26RP) F-F0 base plate unit (#B5024) F-F0 base plate unit (#B5024) Lens contact unit (#B5008) Screw (#1615) Screw (#1615) ・ Remove the sponge (#206). Sponge (#206) - D84 ･ D700 -...
  • Page 91 (#908) Sponge (#909) Sponge Mirror box Mirror-down spring (#262) Be careful NOT to lose the washer (#221). Washer (#221) L-base plate unit (#231RP) FLOCKED SHEET(#166) Mirror unit (#B20204) I-base plate unit (#B71) FLOCKED SHEET(#167) PROTECTOR(#168) Screw (#171) - D85 ･ D700 -...
  • Page 92 7. Rear body IF PCB ・ Take out the two screws (#1510). Screw (#1510)×2 ・ Remove the IF PCB (#5019). IF PCB (#5019) Mold (#396) Lug plate (#397) Connection-FPC (#5040) Screw (#1544) Gasket (#694) Plate (#399) IF PCB (#5019) - D86 ･ D700 -...
  • Page 93 VBA22001-R.3754.A Piezoelectric buzzer Buzzer (#5065) ・ Remove the Buzzer (#5065). SHEET(#891) Buzzer (#5065) ・ Peel off the tape [#TA-0005 (10×20)]. Tape (#TA-0005) Charge base plate unit ・ Take out the four screws (#1573). Screw (#1573)×4 sponge (#710) - D87 ･ D700 -...
  • Page 94 VBA22001-R.3754.A ・ Remove the charge base plate unit (#B620RP). Charge base plate unit (#B620RP) ・ Take out the two screws (#606), and remove the charge motor unit (#B602). Charge motor unit (#B602) Screw (#606)×2 - D88 ･ D700 -...
  • Page 95 VBA22001-R.3754.A ・ Remove the gear (#614). ・ Peel off the Sheet (#825). Sheet (#825) Gear (#614) Shutter unit ・ Take out the three screws (#1570). Screw (#1570)×3 - D89 ･ D700 -...
  • Page 96 VBA22001-R.3754.A ・ Remove the shutter unit (#B12001). Shutter unit (#B12001) Power base unit ・ Peel off the tape [#TA-0005 ( 10×20)]. Pull out the wires from this hole. Tape (#TA-0005) - D90 ･ D700 -...
  • Page 97 ・ Take out the three screws (#1516), and remove the base unit (#B812). Screw (#1516)×3 base unit (#B812) Grip unit ・ Take out the three screws (#1534). Screw (#1534)×3 ・ Remove the grip unit (#B57). Grip unit (#B57) - D91 ･ D700 -...
  • Page 98 ・ Remove the battery contact unit (#B822). Screw (#1595) Battery contact unit (#B822) ・ Remove the FG contact unit (#B824). Screw (#1595) FG contact unit (#B824) ・ Remove the battery contact unit (#B823). Screw (#1595) Battery contact unit (#B823) - D92 ･ D700 -...
  • Page 99 VBA22001-R.3754.A ・ Remove the Mold (#56). Screw (#1567)×3 Mold (#56) Rear body accessories Tape #TA-0019(11.4×5.5) Double-stick tape (#561) Sponge (#609) Double-stick tape (#562) Double-stick tape (#560) - D93 ･ D700 -...
  • Page 100 VBA22001-R.3754.A Assembly / Adjustment 1. Rear body Rear body accessories #TA-0019 Tape [#TA-0019 (11.4×5.5) ] Double-stick tape (#561) Sponge (#609) Double-stick tape (#562) Double-stick tape (#560) #609 #562 #560 #561 - A1 ･ D700 -...
  • Page 101 ・ Mount the battery contact B unit (#B823). ・ Tighten the screw (#1595). Screw (#1595) Boss Battery contact B unit (#B823) ・ FG contact unit (#B824). ・ Tighten the screw (#1595). Screw (#1595) FG contact unit (#B824) Boss - A2 ･ D700 -...
  • Page 102 ・ Mount the battery contact unit (#B822). ・ Tighten the screw (#1595). Battery contact unit (#B822) Screw (#1595) Position as above, then turn over. Boss ・ Arrange the wires as below. Put between bosses for arrangement as above. - A3 ･ D700 -...
  • Page 103 ・ Mount the grip unit (#B57). Grip unit (#B57) Blue: Upper Red: Lower Put wires ([Blue: thick][Red: thick]) inside the cutout. Fit the blue and red wires between the bosses. Screw (#1534)×3 ・ Arrange the wires as below. Boss Cutout - A4 ･ D700 -...
  • Page 104 VBA22001-R.3754.A Power base unit ・ Mount the power base unit (#B812). Screw (#1516)×3 Be careful NOT to pinch the wires. base unit (#B812) ・ Attach the tape [#TA-0005(10×20)]. Put the wires through this hole. Tape (#TA-0005) - A5 ･ D700 -...
  • Page 105 VBA22001-R.3754.A Shutter unit ・ Mount the shutter unit (#B12001). Shutter unit (#B12001) Screw (#1570)×3 - A6 ･ D700 -...
  • Page 106 ・ Attach the gear (#614). ・ Attach the Sheet (#825). Sheet (#825) Gear (#614) area Grease：G-92KA Apply overall around the shaft. ・ Mount the charge motor unit (#B602). ・ Tighten the two screws (#606). Charge motor unit (#B602) Screw (#606)×2 - A7 ･ D700 -...
  • Page 107 VBA22001-R.3754.A ・ Mount the charge base plate unit (#B620RP). Charge base plate unit (#B620RP) Set the shutter FPC by kind of lifting it. Put the wires into each cutout. - A8 ･ D700 -...
  • Page 108 Sponge (#710) ・ Arrange the wires as below. Arrange between bosses. Piezoelectric buzzer ・ Attach the Buzzer (#5065). Buzzer (#5065) Put the wires through this hole. Buzzer (#5065) SHEET(#891) Do NOT press hard on this white area. - A9 ･ D700 -...
  • Page 109 ・ Attach the tape [#TA-0005 (10×20)], and arrange the wires of the piezoelectric buzzer (#5065). Tape (#TA-0005) IF PCB ・ Mount the IF PCB (#5019). ・ Tighten the two screws (#1510). Mold (#396) Lug plate (#397) Connection-FPC (#5040) Screw(#1544) IF PCB (#5019) Gasket (#694) plate (#399) IF PCB (#5019) Screw (#1510)×2 - A10 ･ D700 -...
  • Page 110 L-base plate unit (#231RP) FLOCKED SHEET(#166) Mirror unit (#B20204) I-base plate unit (#B71) FLOCKED SHEET(#167) PROTECTOR(#168) Grease: G-92KA Screw (#171) Reference position FLOCKED SHEET(#166) FLOCKED SHEET(#167) PROTECTOR(#168) Apply to 2 places. Adhesive: Super glue - A11 ･ D700 - August, 19,2008 Changed page (Overall revision)
  • Page 111 Mirror-down spring (#262) Mirror-down spring (#262) Spring hooking position Hook by following the direction. Front body accessories (#907) Sponge (#909) Sponge (#908) Sponge Apply to #907, #908, and #909. Oil barrier: OS-30MEL - A11-1 ･ D700 - Additional page × 1 August, 19,2008...
  • Page 112 Screw (#1521) F-F0 base plate unit (#B5024) Solder here. Boss Boss Direction for positioning ・ Attach the sponge (#206) to ghe front body (#B26RP) along the shape of the concave portion. Concave portion of #B26RP Sponge (#206) - A12 ･ D700 -...
  • Page 113 ・ Mount the front body FPC unit (#B5009) by fitting with the bosses. ・ Tighten the screw (#1503). ・ Attach the sponge (#608) by fitting the shape of the concave portion of the front body (#B26RP). Boss Sponge Front body FPC unit (#B5009) (#608) - A13 ･ D700 -...
  • Page 114 ・ Insert the coupling shaft (#342) into the hole by fitting its shape. coupling shaft (#342) ・Mount the side lever unit (#B355). area Grease：G-92KA Side lever unit (#B355) AF coupling shaft (#342) ・Tighten the screw (#1513). Screw (#1513) - A14 ･ D700 -...
  • Page 115 10-pin FPC (#5010) Solder here. Mounting of Mirror box on Front body ・ Mount the mirror box unit on the front body (#B26RP). Mirror box unit Front body (#B26RP) （Be careful NOT to pinch in the front body.） - A15 ･ D700 -...
  • Page 116 Screw (#1530) ・ Connect the FPC to the connector. ・ Tighten the screw (#1503). Front body FPC unit (#B5009) I-base plate unit (#B71) Screw (#1503) ・ Solder the FPC. I-base plate unit (#B71) AF driving base unit (#10328) - A16 ･ D700 -...
  • Page 117 Front body unit (#B26RP) Release base unit (#B381) Boss ・When mounting the above, leave the black wire exposed short of the 10-pin FPC (#5010) as below. ・ Tighten the screw (#1516) and three screws (#66). screw#1516 screw#66 × 3 - A17 ･ D700 -...
  • Page 118 ・ Attach SB pop-up button (#40) and synchro-mode button (#37). area Grease：CFD409Z Retainer ring (#38) x 2 SB pop-up button (#40) Synchro-mode button (#37) area Grease：CFD409Z ・ Attach the drip-proof sponge (#992) by aligning the reference line. Drip-proof sponge (#992) Oil barrier: OS-30MEL - A18 ･ D700 -...
  • Page 119 ・Put the roller (#407) on the shaft, and hook the spring (#406) to the boss and roller as below. Grease：CFD409Z Roller (#407) Spring (#406) Boss Mounting of Front cover on Front body ・ Mount the apron (#B22) on the front body unit (#B26RP). (#B26RP) Front body unit (#B22) Apron - A19 ･ D700 -...
  • Page 120 Screw (#55) Screw (#55) ・ Mount the SCM changeover lever (#383), and tighten the screw (#387). ・ Mount the cover ring (#388). SCM changeover lever Cover ring (#388) Screw (#387) (#383) Cover ring (#388) Double-stick tape (#389) - A20 ･ D700 -...
  • Page 121 ・ Mount the bayonet mount (#401). Oil barrier: OS-30MEL area Hole of release Back side Bayonet mount (#401) ・ Tighten the screw (#1620). ・ Tighten the four screws (#1621) in numeric order. Screw (#1621)×4 ④ ① ③ ② #1620 - A21 ･ D700 -...
  • Page 122 　　 Standard: 3.35 - 3.45mm 　　 Be careful NOT to bend the lever. ・ In case of nonstandard, make the adjustment by using the adjustment screw. Adjustment screw Adhesive: Screwlock Aperture lever Tool J18004 APERTURE LEVER POSITIONING GAUGE - A22 ･ D700 -...
  • Page 123 Direction for positioning ② ③ AF sensor base plate ① (#B10277) Screw (#1509)×3 ・ Tighten the screw (#283). ・ Attach the Spring (#284). Hook to the V-groove. Screw (#283) Spring (#284) ・ Tighten the screw (#65). Screw (#65) - A23 ･ D700 -...
  • Page 124 Support pole HEX. KEY WRENCH (φ1.5mm) ・ Put the washer (#274) on the support pole of the AF sensor base plate (#B10277). ・ Put the E-ring (#1653). AF sensor unit (#20294) Support pole Washer (#274) E ring (#1653) - A24 ･ D700 -...
  • Page 125 VBA22001-R.3754.A ・ Connect the FPC to the connector. ・ Tighten the screw (#1503). AF sensor unit (#B20294) boss screw#1503 ・ Inser the the connection-FPC (#5042) under the AF motor, fitting with the boss. Boss Connection FPC (#5042) - A25 ･ D700 -...
  • Page 126 Slacken the 10-pin FPC (#5010). Screw (#1663) PD PCB (#5002) Connection-FPC (#5042) Wires of AF motor ([Blue][Yellow]) Wires ([Blue][White][Yellow]) ・ Insert the 10-pin FPC (#5010) under the wires ([Blue][Black]), then connect it to the connector. PD PCB (#5002) 10-pin FPC (#5010) - A26 ･ D700 -...
  • Page 127 ・Attach the tape [#TA-0005 (10×20)] to fix the wires ([Green][Brown]). ・ Attach the connection-FPC (#5042) by fitting with the boss. Boss Tape (#TA-0005) Connection-FPC (#5042) ・ Arrange the yellow wire of the PD PCB (#5002) as below. - A27 ･ D700 -...
  • Page 128 (#1115) SI-LCD holding rubber There are two types of Ａ #1115A 1K105-430 Ｂ #1115B 1K105-510 rubber (A and B). If A type is too tight to be fit in, use B type. - A28 ･ D700 - Changed page △× 1 August, 19,2008...
  • Page 129 (#1117) Rubber ・ Push the head of the plates [ (#1163) and (#1164)] into each square hole of the prism box, fitting with the boss. (#1164) Plate (#1163) Plate Boss ・ Tighten the two screws (#1597). Screw (#1597)×2 - A29 ･ D700 -...
  • Page 130 (#1107) Finder frame ・ Mount the condenser lens (#19). ・ Mount the Spacer Frame (#1109). Spacer Frame (#1109). (#1109) Spacer Frame Top surface (#19) Condenser lens (Be careful of the vertical direction.) - A30 ･ D700 - Changed page (Overall revision) August, 19,2008...
  • Page 131 ・ Place so that the LCD chip can be fit in the central concave portion. (#5011) SI LCD FPC LED chip Boss Cut out (#B1168) SI guide unit ・ Mount the plate (#1167), and tighten the three screws (#1597). Screw (#1597)×3 (#1167) plate - A31 ･ D700 -...
  • Page 132 (#8) Lower display prism (#8) Lower display prism (#1186) Tape ・ Mount the two plates (#1185), and tighten the two screws (#1537). (#1185) Plate ×2 (Be careful of the direction.) Boss Square hole Square hole Screw (#1537)×2 - A32 ･ D700 -...
  • Page 133 ・ Mount the inside finder LCD unit (#B5004). (#B5004) Inside finder LCD unit ・Tighten the two screws (#1585). Screw (#1585)×2 ・ Fit the FPC part of the inside finder LCD unit (#B5004) with the boss. (#B5004) Inside finder LCD unit Boss - A33 ･ D700 -...
  • Page 134 ・ Mount the ・ Tighten the two screws (#1595). (#B1119) Eyepiece Lens Unit Screw (#1595)×2 ・Hook the plate (#1120) at two places as shown in the right Hook picture, then tighten the two screws (#1597). (#1120) plate Screw (#1597)×2 - A34 ･ D700 -...
  • Page 135 ・ Align the "▲" mark of the cam (#1128) with the "▲" mark of the gear (#1125), then assemble them. (#1125) gear area Grease：CFD409Z Alignment mark (#1128) Cam area Grease：CFD409Z ・ Mount the mold (#1123) by fitting with the boss, and tighten the two screws (#1595). (#1123) Mold Screw (#1595)×2 (#1123) Mold #1129 SPONGE - A35 ･ D700 -...
  • Page 136 ・ Attach the steel ball (#1136) first, and then the click spring (#1127). (#1127) Click spring Grease：CFD409Z (#1136) Steel ball Grease：CFD409Z ・ Mount the plate (#1126), and tighten the screw (#1595). (#1126) plate Screw (#1595) ・ Mount the finder frame (#1108), (being careful of the direction.) (#1108) Finder frame - A36 ･ D700 -...
  • Page 137 ・ Attach the tape (#1203) by aligning with the marking-off line so that the tapes do not run off the edge of the prism box unit (#B1101RP). Marking-off line (#1203) tape Do NOT run off the edge. - A37 ･ D700 -...
  • Page 138 ※ Page A138 Screen washer 　A　0.10mm #1180A 1K608-832 Screen washer 　B　0.20 mm #1180B 1K608-833 Screen washer 　C　0.15mm #1180C 1K602-840 Screen washer 　D　0.05mm #1180D 1K608-977 ・ Hook the spring (#1103) to the prism box unit (#B1101RP). Spring (#1103) Hook - A38 ･ D700 -...
  • Page 139 ・ Pass the flanged portion of the SI LED FPC (#5011) into the hole of the penta FPC unit (#B5005) at two places. Penta FPC unit (#B5005) Penta FPC unit (#B5005) SI LED FPC (#5011) SI LED FPC (#5011) ・ Solder as below. - A39 ･ D700 -...
  • Page 140 ① to ③ until the screw point touches the ground, then make two and half turns counterclockwise. Prism box unit (#B1101RP) ・ Tighten the three screws (#1541) in numeric order ( ① → ② → ③ ). ① ② ③ Screw (#1541)×3 - A40 ･ D700 -...
  • Page 141 Mount by pushing the FPC to the sides. Front body unit (#B26RP) ・ Tighten the four screws (#1525) in numeric order ( ① → ② → ③ → ④ ). ④ ① ③ ② Direction for positioning - A41 ･ D700 -...
  • Page 142 VBA22001-R.3754.A ・ Connect the FPC to the connector at two places. Metering FPC unit (#B5006) SI-LCD unit (#B5055) SI-LCD unit (#B5055) Lens contact unit (#B5008) - A42 ･ D700 -...
  • Page 143 ・ Confirm that the FPC edge of the inside finder LCD unit (#B5004) is in the inner cutout section of the prism box unit (#B1101RP) as below. Inner cutout section (#B5004) Inside finder LCD unit ・Connect the FPC to the connector, (being careful of the direction of the connector.) Penta FPC unit (#B5005) Inside finder LCD unit (#B5004) - A43 ･ D700 -...
  • Page 144 (#B1101PR) as below. FPC of SI-LCD unit (#B5055) Inner cutout section ・Connect the FPC to the connector. Penta FPC unit (#B5005) SI-LCD unit (#B5055) ・ Connect the FPC to the connector. Penta FPC unit (#B5005) PD PCB (#5002) - A44 ･ D700 -...
  • Page 145 (supplied) tilted mirror of the inspection tool. Eccentric pin for right- left adjustment #1520×3 Eccentric pin for Adhesive: the sub-mirror Screwlock ※ Apply after Eccentric pin for the adjustment. the main mirror Main mirror shaft base plate - A45 ･ D700 - Changed page △× 1 August, 19,2008...
  • Page 146 　 ±5’ Up-down deviation 　　Distortion 　5’ or less 8’ or less Device △（Revision） J19132 J15432 J15433 HEX. KEY WRENCH (φ1.5mm) 45 DEG ANGLE MAIN-MIRROR MAIN/SUB MIRROR ANGLE TOOL FOR D700 INSPECTION TOOL - A46 ･ D700 - Changed page △× 1 August, 19,2008...
  • Page 147 The shutter curtains are positioned horizontally, so no caulking is seen on the face. －　＋ 3V： In case caulking can be seen on the face, apply voltage (3V) to the charge motor so as to become initial status. - A47 ･ D700 -...
  • Page 148 Mirror-down status to get it down. ・ Mount the front body unit (#B26RP) on the rear body. Caution: The boss must be fit securely. Front body unit (#B26RP) Boss ボス Rear body - A48 ･ D700 -...
  • Page 149 Direction for positioning Screw (#1531) ・ Tighten the five screws (#1575) in numeric order ( ① → ② → ③ → ④ → ⑤ ). ④ ① ⑤ ③ ② ・ Tighten the screw (#1525). Screw (#1525) - A49 ･ D700 -...
  • Page 150 (2) From "0" position of (1), turn the index circle in the direction of the arrow so that the needle is on "0.17mm". (This position is "0" position of D700.) (3) Measure the body back based on "0" position of the index circle.
  • Page 151 In case of the above 2 and 3, when the image PCB is replaced, remove the washer. Mark indication Z 0.1 Z 0.02 Z 0.1 Z 0.02 Device J18001-1 J19004-1 DIAL INDICATOR AND STAND BODY BACK FOCUS GAUGE - A51 ･ D700 - Changed page (Overall revision) August, 19,2008...
  • Page 152 ・ Attach the sponge (#952) to the grip-supporting mold (#58). ・ Attach the grip-supporting mold (#58). ・ Tighten the screw (#1644). Oil barrier:OS-30MEL Sponge (#952) Grip-supporting mold (#58) Position for attachment Screw (#1644) Grip-supporting mold (#58) Changed page (Overall revision) - A52 ･ D700 - October.02.2008...
  • Page 153 AF-assist lamp unit (#B326) Sponge (#325) ・ Mount the AF-assist lamp unit (#B326). ・ Tighten the screw (#1638). AF-assist lamp unit (#B326) Screw (#1638) ボス ボス Boss Main PCB ・ Attach the lug plate (#775). lug plate (#775) - A53 ･ D700 -...
  • Page 154 × 40）] by kind of wrapping the August..2008 （10 × 40） wires and main PCB. ・ Connect the connection-FPC (#5039) to the connector. Connection-FPC (#5039) ・ Mount the main PCB unit (#B5001). Main PCB unit (#B5001) - A54 ･ D700 - Changed page (Overall revision) August, 19,2008...
  • Page 155 ・ By wrapping the tape [#TA-0005 （ 10×20)], arrange the wire edge of the piezoelectric buzzer (#5065) and the black and red wires. Wire of AF-assist lamp unit (#B326) Direct the wires outwards. Wire of piezoelectric buzzer (#5065) Tape (#TA-0005) - A55 ･ D700 - Changed page (Overall revision) August, 19,2008...
  • Page 156 VBA22001-R.3754.A ・ Solder at eight places. ・ Solder the FPC at three places. Wire [Yellow] Wire [Black; AF-assist lamp]×2 Wire [Gray] Wire[Black; buzzer]×2 Wire [Blue] Wire [Orange] - A56 ･ D700 - Changed page (Overall revision) August, 19,2008...
  • Page 157 ・ Solder the wire [Blue] of the battery contact unit (#B822) on the FPC. FPC of lens contact FPC unit (#B5008) Wire [Blue] DC/DC PCB ・ Attach the harness (#5071). ・ Attach the harness (#5070). DC/DC PCB (#5047) Harness (#5070) Harness (#5071) - A57 ･ D700 - Changed page (Overall revision) August, 19,2008...
  • Page 158 Be careful so that the wires do NOT run on the body. Boss ・Tighten the four screws (#1509) in numeric order ( ① → ② → ③ → ④ ). ① ③ Screw (#1509) Screw (#1509) ④ ② DC/DC PCB (#5047) - A58 ･ D700 -...
  • Page 159 ・ Solder at eight places. ・ Attach the FPC. Wire [Yellow] Wire [Gray] Wire [Brown] Wire [Blue; charge motor] Wire [Green] Wire [Red; charge motor] Wire [Blue] Wire [Brown] ・ Solder the wires ([Gray][Orange][Red]). Wire [Red] Wire [Orange] Wire [Gray] - A59 ･ D700 -...
  • Page 160 ・ By wrapping the tape [#TA-0005 (10×3.7)] arrange the wires ([Green][Brown]). Be careful so that the tape (#TA-0005) does NOT cover dotted area. Tape (#TA-0005) The wire must NOT cover the above protrusions. The wire must NOT run on the dotted area. - A60 ･ D700 -...
  • Page 161 Set the camera AF to manual, and rotate the focus ring to set to "0.7 m". ⑦ Start up the inspection and adjustment software for D700 (J65119), and select "Inspection and Adjustment for AE CCD POSITION" then "Set Camera for AE CCD POSITION" to lighten the focus area.
  • Page 162 X direction X direction (a) Loosen (a) Tighten Reference X direction Screw ａ Y direction (b) Loosen ・Because the screw ① is the reference screw, do NOT rotate it for adjustments unless absolutely necessary. Must be within standard - A62 ･ D700 -...
  • Page 163 (#1659) area. #765×2 #766×2 ・ Mount the AF-assist lamp protector (#327), and apply the super X. ・ Attach the Tape (#709). Super X Tape (#709) AF-assist lamp ptotector (#327) ・Attach the Tape (#972). Tape (#972) - A63 ･ D700 -...
  • Page 164 ・ Apply the super X to around the mold (#510). Mold (#510) Super X ・Attach the synchro-terminal (#50), and tighten the screw (#1532). Apply to approx. two threads of the screw. Screw (#1532) Adhesive: Locktite Synchro-terminal (#50) - A64 ･ D700 -...
  • Page 165 Mode dial ･ Attach the base plate (#505), and tighten the screw (#1571) and two screws (#1609). Screw (#1571) Base plate (#505) Screw (#1609) Mode dial FPC (#5025) Double-stick tape (#514) Double-stick tape (#515) Base plate (#505) - A65 ･ D700 -...
  • Page 166 Screw (#1640) x 2 Washer (#511) ・ Pass the FPC of the trefoil button unit through the hole of the mode dial base plate (#505), and tighten the screw (#1574) from behind. screw#1574 Base plate (#505) Trefoil button unit - A66 ･ D700 -...
  • Page 167 ・ Tighten the screw (#1565). Oil barrier: OS-30MEL Screw (#1565) SB lock lever (#309) Spring (#310) Boss Hook Retainer plate (#312) Oil barrier：OS-30MEL SPONGE#188 SB lock lever (#309) Oil barrier: OS-30MEL area Spring (#310) SHEET#917(A-C) Retainer plate (#312) - A67 ･ D700 -...
  • Page 168 Grease：G-92KA Grease：CFD409Z Back side DOUBLE STICK TAPE(#515) Washer (#751) area Grease：G-92KA Main Sw Base Plate Unit (#B745) Screw (#1557)×2 ・By putting the washer (#744) from rear side, as if pinching the E-ring (#1652). E-ring (#1652) washer (#744) - A68 ･ D700 -...
  • Page 169 ・ Attach the metering mode FPC (#5028) by fitting with the protruded portion. Metering mode FPC (#5028) Protruded portion ・ Mount the AE mode dial (#781) and AE-Lock button (#780) as below. AE mode dial (#781) AE-Lock button (#780) area Drysurf：MZ-800SEL - A69 ･ D700 -...
  • Page 170 ・ Apply the super X to the below area, and attach the conducting button (#730). Super X Conducting button (#730) ・ Attach the conducting button (#787) from the rear side by fitting with the rib. Conducting button (#787) - A70 ･ D700 -...
  • Page 171 SW (#39) Top cover FPC (#5003) Double-stick tape#753 Double-stick tape#913 Power plate Double-stick (#747) Mold(#703) tape#912 Spring (#746) Sponge(#965) Screw (#1537)×2 Tape (#929) ・ Mount the top cover FPC (#5003). Top cover unit (#B23RP) Top cover FPC (#5003) - A71 ･ D700 -...
  • Page 172 SUPPORT PLATE (#731) Screw (#1540) ・Attach the top cover FPC (#5003) to the support plate (#731). ・Attach the spring (#750), and tighten the screw (#1606). area Grease：G-92KA Screw (#1606) Spring (#750) Support plate (#731) Top cover FPC (#5003) - A72 ･ D700 -...
  • Page 173 ・ Tighten the four screws (#321) in numeric order. ・ Solder at four places. ・ Apply the super X to the four screws (#321). Solder Screw (#321) Screw (#321) ② ④ ① ③ Super X Solder ・ Connect the FPC to the connector. - A73 ･ D700 -...
  • Page 174 Check whether to be caught on the FPC or not. area Grease：CFD409Z SB lower case unit (#B302) ・ Attach the collar (#B306) from inside. (Be careful of the bending of the brush.) Collar (#B306) Check the direction. - A74 ･ D700 -...
  • Page 175 ・Pass the wires from outside as below, and divide them into wires ([Gray][Red][Blue]) and wires wires ([Gray][Red][Blue]) and wires ([Orange][Black][Green]) for arrangement. [Orange][Black][Green]) for arrangement. ・ Tighten the screw (#1601). Grease：GN- Inner half 20SB Pass the wires from outside. [Orange][Black][Green] screw#1601 [Gray][Red][Blue] - A75 ･ D700 -...
  • Page 176 ・ Attach the two screws (#1623) to the SB upper cover (#301). Screw (#1623) ・Hook the two SB pop-up arms (#322), and tighten the two screws (#796). SB pop-up arm (#322) Grease：CFD409Z Hook Be careful of assembling direction. Screw (#796) Screw (#796) - A76 ･ D700 -...
  • Page 177 VBA22001-R.3754.A Release SW ・Attach the release SW unit (#B735) by fitting with the bosses. Release SW unit (#B735) ・ Tighten the screw (#1605). ・ Attach the Tape (#949). Tape (#949) Screw (#1605) - A77 ･ D700 -...
  • Page 178 ・Mount the SB PCB (#5013). ・ Tighten the two screws (#1541). ・ Solder the wires ([Yellow][Green][Black][Orange][Gray][Blue][Red]). ・ Connect the FPC to the connector. Screw (#1541) SB PCB (#5013) [Yellow] Screw (#1541) [Green][Black][Orange][Gray] Boss Boss [Blue][Red] ・Attach the tape (#929). tape#929 - A78 ･ D700 -...
  • Page 179 VBA22001-R.3754.A ・Solder the wires ([Black][Red][Yellow]) of the metering mode FPC. [Black][Red][Yellow] ・ Attach the tape (#929) at two places. ・ Put the wires in the cutout together for arrangement. Cutout Tape (#929) - A79 ･ D700 -...
  • Page 180 ・ Position the sub-command dial unit (#B725) in the direction of the arrow for mounting. Then, tighten the two screws (#1544). (#B725) Sub-command dial unit Direction for positioning (#951) Sponge Sub-command dial unit (#B725) Screw (#1544) Rear C/D unit (#B726) (#920) Sponge screw#1571 ・Solder at three places. - A80 ･ D700 -...
  • Page 181 ・ Attach the top cover FPC (#5003) and release SW FPC (#5033) by fitting the bosses, and solder them as below. ・ Attach the tape [#TA-0005 (10×20)]. Release SW FPC (#5033) Top cover FPC (#5003) Tape (#TA-0005) Main condenser ・ Solder the wires [Black][Red] of the main condenser (#5067). Wire [Black] Wire [Red] - A81 ･ D700 -...
  • Page 182 (ref. Page A61 ） ・ Connect the FPC. ・ With the SB being raised, mount the top cover on the body. SB pop-up button (#40) Leave the SB open. With the SB pop-up button (#40) being sticking out, make assembly. - A82 ･ D700 -...
  • Page 183 While pressing the release hook of SB towards the direction of the arrow, make assembly. ・ Tighten the two screws (#1548) in the order from ① to ② . ① ② Screw (#1548)×2 ・ Get the SB down. - A83 ･ D700 -...
  • Page 184 ・ Tighten the two screws (#1509) in the order from ① to ② . Screw (#1509)×2 ② ① ・ Tighten the two screws (#1511) in the order from ① to ② . ・ Tighten the screw (#1512). Screw (#1512) ① ② Screw (#1511)×2 - A84 ･ D700 -...
  • Page 185 VBA22001-R.3754.A ・ Tighten the two screws (#1512). Screw (#1512) Screw (#1512) ・ Solder the wires ([Green][Brown]). Wire [Brown] Wire [Green] - A85 ･ D700 -...
  • Page 186 VBA22001-R.3754.A ・ Attach the double-stick tape (#915). Double-stick tape (#915) ・ Mount the condenser. Mount parallel ・ Arrange the wires as below. - A86 ･ D700 -...
  • Page 187 ⑤ Mount the AF50/1.4D on the camera, and set the focus ring to INFINITY. ⑥ Start D700 camera inspection and adjustment software. ⑦ Set the light-receiving adapter (J61230) to the shutter section of the camera, and attach the light-receiving sensor of the shutter tester.
  • Page 188 ⑤ Mount the AF50/1.4D on the camera, and set the focus ring to INFINITY. ⑥ Start D700 camera inspection and adjustment software. ⑦ Set the light-receiving adapter (J61230) to the shutter section of the camera, and attach the light-receiving sensor of the shutter tester.
  • Page 189 When this camera is used for measuring the consumption current value, set the MB-D10 and wire as follows. * Modify "MB-D10" and connect wires. 7.40V － ＋ ＋ － Ａ MB-D10 Device MB-D10 POWER SUPPLY(10V 5A) Modified power code BATTERY PACK ＭＢ－Ｄ１０ - A89 ･ D700 -...
  • Page 190 Eyepiece shutter base (#B1141) Eyepiece shutter (#1145) Sponge (#1201) Eyepiece shutter (#1144) Pin (#1152) Washer (#1147) Screw (#1146) Spring (#1151) E ring (#1652) Screw (#1542) Lug plate (#1206) ・ Mount the eyepiece. ・ Tighten the screw (#1534). Screw (#1534) Eyepiece - A90 ･ D700 -...
  • Page 191 Diopter adjustment knob (#1121) Screw (#1552) Fit in the concave portion. Convex portion Body side Diopter adj. knob side ・ Attach the cover (#1130). Cover (#1130) Double-stick tape (#1154) Cover (#1130) Changed page (Overall revision) - A91 ･ D700 - October.02.2008...
  • Page 192 ・ Connect the connection-FPC (#5038) to the connector of the CF PCB (#5018). ・ Position the lever of CF PCB (#5018) towards the direction of the arrow. Connection-FPC (#5038) CF PCB (#5018) ・ Mount the CF-PCB (#5018). CF PCB (#5018) Boss - A92 ･ D700 -...
  • Page 193 ※ Washer ※ Washer(#531) Harness (#5072) ※ Washer ※ As for some bodies, the attaching surface and lateral face of the image sensor unit (#B20521) have wash- ref.Page A51 ers attached. - A93 ･ D700 - Changed page (Overall revision) August, 19,2008...
  • Page 194 Play back the image of the shot QR code, and confirm that reading of the QR ＊ Perform "QrReader (J65096)". code on the playback screen can be read out with two-dimensional barcode reader. (Refer to Page A129 for how to set two-dimensional barcode reader.) △（Addition） △（Addition） - A94 ･ D700 - Changed page △× 2 August, 19,2008...
  • Page 195 Image sensor unit (#B20521) Place the wires ([Brown][Orange]) under the image sensor unit. ・ Attach the harness(#5073). ・ Attach the tape [#TA-0005 （ 5×15 ） ] for arranging the wires ([Brown][Orange]). Tape (#TA-0005) Harness (#5073) Connector Image sensor unit (#B20521) - A95 ･ D700 -...
  • Page 196 Push the wire to the sides. Push the FPC to the sides. Pass the harness (#5073) through the gap of the PCB as above. Boss DG PCB unit (#B5017RP) Boss Screw (#1521) Push the FPC to the sides. - A96 ･ D700 -...
  • Page 197 Wire [Black thin] Wire [Orange] ・ Solder the wires ([Red thick][Black thick][Brown]). Wire [Brown] Wire [Red thick] Wire [Black thick] ・ Attach the power pack connection-FPC. Connection-FPC (#5027) Power pack connection-FPC Sheet (#816) Tape (#815) Rubber (#814) - A97 ･ D700 -...
  • Page 198 VBA22001-R.3754.A ・ Connect the four FPCs. ・ Connect the two harnesses to the connectors. Connector ・ Connect the FPC. Connector ・ Connect the two harnesses to the connectors. Connector Connector - A98 ･ D700 -...
  • Page 199 ・ Mount the DG shield plate unit (#B683), and tighten the five screws (#1521) in numeric order ( ① → ② → ③ → ④ → ⑤ ). ⑤ ③ ① ② ④ DG shield plate unit (#B683) I/F cover I/F cover (#28) Sponge (#969) Screw (#1642)×2 I/F lid (#392) Sponge (#975) Mold (#395) - A99 ･ D700 -...
  • Page 200 VBA22001-R.3754.A ・ Mount the I/F cover (#28). ・ Tighten the two screws (#1510) in the order ( ① → ② ). I/F cover (#28) Screw (#1510)×2 Direction for ② ① positioning - A100 ･ D700 -...
  • Page 201 ★： New tool (If required) To marketed straight cable RS232C MC-31 USB cable (UC-E4） ★ J18433 D700 inspection and adjustment software MB-D10 Stabilized power source Set value ＝ 12V 　5.0A AC adapter (EH-5） Caution: When the voltage adjustment is made, use MB-D10.
  • Page 202 VBA22001-R.3754.A D700 Inspection and Adjustment Software (J65119) This inspection and adjustment software runs on Windows. Install the software by following the below procedure. <Operating environment> Check the following operating environment which is required for installing this program on PC. IBM PC/AT compatible...
  • Page 203 <Procedure for installation> Because this is the self-extracting file, decompress the file before installing, and follow the next procedure. 1. Create a folder for installation under any drive and name. C: ￥DeskTopLauncher\D-SLR\D700 2. Paste the file (PD700.EXE) in the created folder.
  • Page 204 4. When the decompression of file is finished, the file (D700.exe) is created. 5. The install is completed. 【Start-up of Program 】 1. When "D700 ． EXE" is started, the following window will appear. So type in the user key. (ref. TIE07023) Caution: Once the user key is typed, from the next time, the adjustment screen will appear from the beginning.
  • Page 205 ※ When the camera body (excluding imaging) is inspected and adjusted, the USB connection will be reset in the process of writing the data into the camera. Therefore, the following message will appear but does not affect the adjustment. Click "Cancel", and proceed with the next. - A105 ･ D700 -...
  • Page 206 (3) Select "Search for a better drive than the one your device is using now. (Recommended)", and click "Next". (4) Click "Reference" of "Specify a location" and select the directory where the driver was copied, such as "C: ¥D700¥PTP". Then click “Next”. - A106 ･ D700 -...
  • Page 207 VBA22001-R.3754.A (5) Confirm that the driver is located at the right place, and click "Next". (6) Click "Finish". (7) Reboot the PC to complete the installation. - A107 ･ D700 -...
  • Page 208 Whenever the metering FPC unit is disassembled/replaced or the main PCB is replaced, make this adjustment. Device J18267 J19123 AF50/1.4D AF28/2.8D SHUTTER TESTER EF-1(CE) LENS AF50/1.4D LENS AF28/2.8D AF70-300/4-5.6D OR AF-SVR70-300/4.5-5.6 LENS AF70-300/4-5.6D OR LENS AF-SVR70-300/4.5-5.6 - A108 ･ D700 - Changed page △× 2 August, 19,2008...
  • Page 209 When performing "obtain of AE sensor reference value", set the metering mode to "Multi-pattern". For AE sensor reference value, copy the D3 data file "D3SEEN.DAT" into the folder and use it. Device J19123 SHUTTER TESTER EF-1(CE) AF50/1.4D LENS AF50/1.4D - A109 ･ D700 - Changed page △× 3 August, 19,2008...
  • Page 210 VBA22001-R.3754.A AF inspection and adjustment Caution: When this adjustment software is used for the first time, prepare three D700 cameras, and measure by "Writing of AF adj. lens offset value" on the main menu. ①　AF accuracy adjustment ( All the adjustments items will be made in order.) Caution: Whenever the AF sensor unit is disassembled/replaced or the main PCB is replaced, make this adjustment.
  • Page 211 7. When the adjustment is completed at 6, make the YAW/PITCH inspection & adjustment . 8. Make the XY inspection and adjustment. X adjusting screw Screw (#1509)×3 Device J19123 J63098 　　　AF X-Y CHART FOR D3 SHUTTER TESTER EF-1(CE) - A111 ･ D700 - Changed page △× 1 August, 19,2008...
  • Page 212 Z ADJUSTMENT LENS (FOR 1m) ILLUMINATION BOX FOR AF ADJUSTMENT J15407 MULTI CAM 2000 AF CHART 《USB or RS232C communication》 ⑤　AF shift adjustment Device J18393 J19124 J18267 　Z-light LENS AF50/1.4D SLANT CHART Changed page (Overall revision) - A112 ･ D700 - October.02.2008...
  • Page 213 （ High frequency of rewriting Low frequency of data) rewriting data) Fixed value, adjustment No. of times for releasing shut- value, etc. ter, error history, custom menu setting, etc. - A112-1 ･ D700 - Additional page × 1 August, 19,2008...
  • Page 214 Records (history) of errors which happened to camera can be confirmed. They will be shown as "Latest error, HIST 1, HIST 2・ ・ ・ " in order, and the further previous records will be shown in trouble history. (EXIST, NON only) - A112-2 ･ D700 - Additional page × 1...
  • Page 215 ＊ 2: Make the inspection. ＊ 3: Whenever "AE sensor inspection and adjustment" is made, assemble up to the stage of DG-PCB unit, and make the inspection and adjustment via USB. - A113 ･ D700 - Changed page △× 1 August, 19,2008...
  • Page 216 #421 Inner wall area Apply to the inside sliding surface, protrusion Grease：CDF-4092 #986 #962 #987 Oil barrier OS-30MEL #961 #421 #963 #421 outside surface #924 Oil barrier：OS-30MEL #925 area: Grease must NOT be attached #455 area Oil barrier OS-30MEL - A114 ･ D700 -...
  • Page 217 #426 Direction for positioning #1593×3 Apply to out- #475 side surface Apply to 3 places area Adhesive: Super glue Adhesive: Super glue Grease：G-92KA #B469 #B478 #1630 #485 #457 #1542×2 #458 #1560×5 #B467 #470 #456 #B5020 #1589×3 #422 - A115 ･ D700 -...
  • Page 218 #435×2 Direction for position- ing when tightening the screw. #5057 #955 Direction for position- ing when attaching #5057. Reference position #432 for attaching #955. #1626×3 Place under the rear cover FPC. Be careful NOT to catch FPC. - A116 ･ D700 -...
  • Page 219 Direction for position- ing when tightening the #429 screw. #425 area Grease：CFD409Z C/F lid unit (#B423) area Adhesive: Super X area Grease： #445 CFD409Z C/F cover unit (#B441) Mount the shaft retainer plate. - A117 ･ D700 -...
  • Page 220 VBA22001-R.3754.A ・ Attach the CF cover unit (#B441) to the back cover unit (#B421RP). Back cover unit (#B421RP) CF cover unit (#B441) ・ Tighten the two screws (#1518). Direction for positioning Screw (#1518)×2 - A118 ･ D700 -...
  • Page 221 VBA22001-R.3754.A Mounting of Back cover ・ Connect the three FPCs. ・ Mount the back cover. - A119 ･ D700 -...
  • Page 222 ・ For easy mounting, first ① set the CF card side, and then ② the IF cover side. Direction for positioning ① ② ・ Tighten the two screws (#1529) in the order from ① to ② . ② ① Screw (#1529)×2 - A120 ･ D700 -...
  • Page 223 ・ Tighten the two screws (#1545) in the order from ① to ② . △（Addition） Caution: In case the length of the screw is different between ① and ② , use the longer one for ① . Screw (#1545)×2 ① ② - A121 ･ D700 - Changed page △× 1 August, 19,2008...
  • Page 224 ・ Tighten the two screws (#1529) in the order from ③ to ④ . ・ Tighten the three screws (#1517) in the order from ⑤ to ⑦ . Screw (#1517)×3 ⑤ ⑥ ④ ⑦ ③ ② ① Screw (#1529)×2 Screw (#1528)×2 - A122 ･ D700 -...
  • Page 225 (#883) Screw (#1509) ・ Tighten the screw (#1509). Screw (#1509) Battery lid Mount from the side to avoid breaking the ・Mount the battery lid unit (#B801). shaft. Battery lid unit (#B801) Battery lid unit (#B801) area Grease：CFD409Z - A123 ･ D700 -...
  • Page 226 Double-stick tape (#946) Double-stick tape (#947) Grip rubber unit (#B60) Grip rubber unit (#B60) ・Tighten the screw (#1647). Screw (#1647) ・ I/F rubber unit (#B10061). Double-stick tape (#546) I/F rubber unit (#B10061) Tape #TA-0004(4.4×4.4) I/F rubber unit (#B10061) - A124 ･ D700 -...
  • Page 227 VBA22001-R.3754.A ・ Attach the rear rubber unit (#B447). Rear rubber unit (#B447) ・ Attach the bottom cover unit (#B63). ・ Attach the rubber cap (#68). Bottom cover unit (#B63) Rubber cap (#68) - A125 ･ D700 -...
  • Page 228 Shooting-image Adjustment 1. Summary When the D700 shooting image-related and listed parts on Page A128 are replaced, be sure to make this adjust- ment by the shooting image adjustment software for D700 (J65120). Use the D3 reference body beforehand, and get the reference value. Getting reference value will create the reference data "D700BSD.DAT"...
  • Page 229 "PD700IMG.EXE". This file is an self-extracting file, so decompress it in the created folder. ※ Be sure to copy the above file in the same directory. Note that the adjustment can not be made except in the above folder. - A127 ･ D700 -...
  • Page 230 *3. There is no menu screen, but when "Gain difference adjustment among channels" is performed, the serial number and QR code data can be input by selecting whether to replace the PCB/base plate or not. - A128 ･ D700 -...
  • Page 231 USB terminal. picture, which is supplied with ・Read the bar codes shown below. a two dimensional barcode reader. ・After the reading, the dialog box that shows the new hardware is recognized will be displayed. ・Click "Next". - A129 ･ D700 -...
  • Page 232 VBA22001-R.3754.A ・Insert the CD-ROM which is supplied with a two-dimensional barcode reader into the PC. ・Insert the CD-ROM which is attached to the two-dimensional bar code reader ・Click "Finish" and take out the CD-ROM from the PC. - A130 ･ D700 -...
  • Page 233 [Properties] → [Hardware] → [Device Manager]. Note:The port setting differs depending on the PC environment. e.g. Setting to COM4 COM number differs depending on the PC environment. ・Set the same port as confirmed by the device manager. - A131 ･ D700 -...
  • Page 234 Using the shutter tester (L12), the adjustment is made with the tool lenses (F1.4 and F8). Area Area Area Area ① ② ③ ④ ① ② ③ - A132 ･ D700 - Changed page △× 2 August, 19,2008...
  • Page 235 (4266×2842-pixels) into (29×25-pixels); Area ③ ; 4 corners of (4×6-pixels) after dividing (4266×2842-pixel) into (29×25-pixels)]. Area ③ Area ③ 4×6 4×6 Area ① Area ② 2128×1416 29×25 Area ③ Area ③ 4×6 4×6 Device J19123 J61185 D1 STANDARD LENS SHUTTER TESTER EF-1(CE) - A133 ･ D700 -...

  • Page 236: Sensitivity Ratio Adjustment

    Using the color viewer (LV13 equiv.) and tool lens (F5.6), inspect whether a difference from the reference body is in the range of standards. Device J61185 J63070 COLOR VIEWER D1 STANDARD LENS - A134 ･ D700 - August, 19,2008 Changed page (Overall revision)

  • Page 237: Tilted Sensor Inspection & Adjustment

    (Angle offset standard: from "-1 deg." to "+1 deg. ） ※ Green letters mean "up to standard", while red means "NOT up to standard) Tilted sensor checking chart Mounting surface of Image-PCB AF50/1.4D approx. 0.7 ｍ - A135 ･ D700 - August, 19,2008 Changed page (Overall revision)

  • Page 238: Tft Adjustment

    ・Sensitivity/sensitivity ratio reference value calculation Using the tool lens (F5.6), the reference body is faced to the color viewer (LV 13 equiv.). Then, measure the level of sensitivity and sensitivity ratio, and the result is stored in the D700BSD.DAT file. - A136 ･ D700 -...

  • Page 239: Initial Settings (Factory Default Settings)

    (15) Version No./ Serial No. RISC firmware version and serial number are indicated. Serial number can be written. ※ Whenever the license sheet is replaced, be sure to input the serial number. - A137 ･ D700 - Changed page △× 3 August, 19,2008...
  • Page 240 Screen washer 　A　0.10mm #1180A 1K608-832 Screen washer 　B　0.20 mm #1180B 1K608-833 Screen washer 　C　0.15mm #1180C 1K602-840 Screen washer 　D　0.05mm #1180D 1K608-977 +0.01 ～ -0.05 ｍｍ Device J19001 J15432 J18010 COLLIMATOR F=600mm INFINITY STANDARD LENS 50/1.8 FOCUS SCREEN FOR D700 - A138 ･ D700 -...
  • Page 242 VBA22001-R.3754.A - E1 ･ D700 -...
  • Page 243 VBA22001-R.3754.A - E2 ･ D700 -...
  • Page 257 Clearance for up-mirror in mirror box: None Visual check Play: 0.2 mm or less Feeling in hand 59 ゜ angle: Up-down 0’ +5’/-30’ Sub-mirror 　　　　　 Right-left ± 20’ Distortion: 8’ or less Sub-mirror tool ∞ Infinity focus From "-80" to "+40" μm - R1 ･ D700 -...
  • Page 258 Shutter curtain speed Both front and rear curtains (up-down 21 mm or less): approx. 2.45 ms or less Shutter curtain bound Black/white bound (within frame): None Synchronization Timelag: (16.6mm-frame): From "- 0.1" to "0.4" ms - R2 ･ D700 -...
  • Page 259 Release when vibration reduction lens attached: : 60 ms or less Power tool Pre-flash release: 100 ms or less VR70-200ED/F2.8G AF-M, AE-A, AMP SB-800 (Multi- sensor balanced fill- flash) Measure the time taken from releasing the shutter to switch- ing ON for X-signal. - R3 ･ D700 -...
  • Page 260 Level 2　2 lights up　Charge remaining: 21-40% battery information Level 1　1 light up　Charge remaining: 1-20% Communication- Level 0　1 light blinking　Charge remaining: 0% capable battery tool When special Li-ion is used: 90 minutes or more Bulb battery life Clock Remote wire - R4 ･ D700 -...
  • Page 261 ISO2500 1/25 LV10+ND32 ISO3200 1/30 LV10+ND32 ISO4000 1/20 LV10+ND64 ISO5000 1/25 LV10+ND64 ISO6400 1/30 LV10+ND64 AE: M mode Distance from object: Closely contact Focal length: Infinity Image size:L, M, S WB: Preset (for every sensitivity) - R5 ･ D700 -...
  • Page 262 Light source: Artificial sunshine Standard For every color AE: M (F5.6） Difference from target value: △ C ＝ 3 or less Color mode: Mode Ⅰ Image quality: JPEG Image size: L ISO Lo1.0, Lo0.7, lo0.3, 200,400,800,1600,3200, 6400,Hi1,Hi2 - R6 ･ D700 -...
  • Page 263 Total of luminescent pixels and black pixels: 3 or less (1 or less in "A" area） A : 19.08×25.44mm A': 38.16×50.88mm (excluding "A"） A’ (The size in height and width is measured by aligning the center of the monitor.) Backlight life 5000 hours or more (at less than 40℃ ) - R7 ･ D700 -...
  • Page 264 FOR D2SERIESE MULTI CAM 2000 AF CHART J15409 チャートボード FOR D2SERIES, D40 CHART BOARD J18001-1 ボディバック出し工具 BODY BACK FOCUS GAUGE J18004 絞りレバー高さ点検工具 APERTURE LEVER POSITIONING GAUGE J18010 無限大合致基準レンズ５０／１． ８ 払底品 INFINITY STANDARD LENS 50/1.8 OUT OF STOCK - T1 ･ D700 -...
  • Page 265 KYORITSU ELECTRIC EF-8000 SHUTTER TESTER EF-1(CE) USABLE J19132 メイン・サブミラー角度検査機 FOR D300, ETC MAIN/SUB MIRROR ANGLE INSPECTION TOOL J61185 撮像関係調整用レンズ FOR D-SLR D1 STANDARD LENS J61222 二次元バーコードリーダー FOR S10 ETC TWO-DIMENSIONAL BARCODE READER J61223 ライティングルーペ FOR D-SLR LIGHTING LOUPE - T2 ･ D700 -...
  • Page 266 J63097 Ｄ３用ＡＥ　ＣＣＤ用チャートボード AE/CCD USE CHART BOARD FOR D3 J63098 Ｄ３用ＡＦ　Ｘ－Ｙチャート AF X-Y CHART FOR D3 J15432 D700 用合致スクリーン ★ FOCUS SCREEN FOR D700 J15433 ★ D700　４５度メインミラー工具 △（Revision） 45 DEG ANGLE MAIN-MIRROR TOOL FOR D3 D700 J65096 ＱＲリーダーソフト FOR S10 ETC...
  • Page 267 MARKETED STRAIGHT CABLE RJ IS NOT AVAILABLE 汎用品 　　　　　　　フラッシュメーター RJ IS NOT AVAILABLE FLASH METER 　安定化電源（10 Ｖ　5 Ａ ) 汎用品 POWER SUPPLY(10V 5A) RJ IS NOT AVAILABLE 　　　　　　　　　ＭＢ－Ｄ１０　　　　　　　　　 製品転用 　BATTERY PACK ＭＢ－Ｄ１０ RJ IS NOT AVAILABE - T4 ･ D700 -...
  • Page 268 VBA22001-R.3754.A 工具番号 名　称 備　考 Tool No. Name of tool Others J18360 基準反射布 FOR C-DSC (L15,L11 etc) Standard reflector 1.5M × 1.5M J18393 斜めチャート SLANT CHART J19124 Z ライト Z-light - T5 ･ D700 -...

Table of Contents