Table of Contents What’s in the Box………………………………………………………………………….. Hardware Installation… …………………………………………………………………… Cable Management Installation………………………………………………………….. Connecting your LCD/Keyboard………………………………………………………… Operating your LCD/Keyboard..…………………………………………………………. Navigating the Menu .………………………………………………………………………. On-Screen Display (OSD) Menus………………………………………………………… Trouble Shooting Image Quality…………………………………………………….…… Specifications………………………………………………………………………………. Warranty……………………………………………………………………………………… 07/01/06 Rev 1.0 1U 17” & 19 LCD and Sun Keyboard Installation guide for the RFT2-17/19 In to a 4-post 19-inch EIA cabinet Page 1 of 13...
RFT2 Rack Kit Installation Guide Box Inventory As you unpack the kit, ensure that you have the following items included in the box: 1 – 1U LCD with Keyboard 1 – 3m HD-15 to HD-15 Video Cable 1 – 3m DVI-D to DVI-D Video Cable 1 –...
RFT2 Rack Kit Installation Guide Hardware Installation Step The following instructions assume that your equipment rack utilizes caged nuts. If you rack has pre-tapped holes there will be no need to include the caged nuts and the size of the mounting bolts may vary from that described.
Page 4
RFT2 Rack Kit Installation Guide Step 3. Remove the slides from the tray assembly. The slides come shipped attached to the tray assembly, the outer slide members must be removed to be properly installed into the rack. To remove the outer slide members, fully extend both slides to the open position.
Page 5
RFT2 Rack Kit Installation Guide Step 6. Attach the left slide rail assembly to the rack mounting rail by using (4) #10-32 x front and rear slide mounting brackets. 7. Repeat for the right slide rail assembly. 8. Extend the slides from the rack. 9.
RFT2 Rack Kit Installation Guide Cable Management Installation 1. With the RFT installed, go to the back of the rack to install the cable management system. 2. Attach Part A to part extension of outer member on the left slide. 3.
RFT2 Rack Kit Installation Guide Connecting your LCD/Keyboard Step ! Note: Before connecting the LCD monitor/keyboard to a KVM or Server, all systems should be turned off. The keyboard and trackball’s design allows it to be used with most Sun systems.
RFT2 Rack Kit Installation Guide Operating the LCD/Keyboard NOTE: It is important to ensure that the monitor is connected and powered on prior to powering up the connected server and/or KVM. Powering up the KVM then the server last will with some servers allow the video card and monitor to self configure to the correct settings.
RFT2 Rack Kit Installation Guide Navigating the Menu (The OSD Controls may be located on the back or the top of the LCD head) Although not required, you can make numerous adjustments to your monitor using the on-screen menu. To access the OSD (On-Screen Display) menu Press the MENU button located at the top of the LCD monitor.
RFT2 Rack Kit Installation Guide On-Screen Display (OSD) Menus The menu pages can be displayed by pressing the Menu button. Not all menu functions can be adjusted. (Menu items or layout may change without notice) Picture: Controls for Picture Quality (most of these settings are optimized by using the “Auto Adjust”...
RFT2 Rack Kit Installation Guide Trouble Shooting Bad Image Quality Image quality problems (blurry characters, distorted images, etc) are usually caused by one of the following: The graphics card is running at the wrong resolution for the LCD monitor: The monitor optimally runs at a resolution of 1280x1024x60Hz. To display the monitor resolution, press the Menu Button at the top of the LCD twice.
RFT2 Rack Kit Installation Guide Warranty Neuro Logic Systems warrants to the original retail purchaser that this product is and will be free from defects in materials and workmanship for a period of 24 months from the date of purchase. During the warranty period, purchaser must promptly call Neuro Logic Systems (+1.805.389.5435) to log any such defects in materials and...