Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for NETGEAR FS102
Summary of Contents for NETGEAR FS102
-
Page 2: Start Here
• Two vista RJ-45 connector ports on the Model FS102 switch, four vista RJ-45 connector ports on the Model FS104 switch, and eight vista RJ-45 connector ports on the Model FS108 switch (Each port has built-in LEDs to monitor individual port status.) -
Page 3: Package Contents
Warranty & Owner Registration Card • Support Information Card • AC power cord and universal power cord adapter Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide Model FS104 switch FS104 FAST ETHERNET SWITCH 100 Mbps 1 2 3 4... -
Page 4: Product Illustration
Fast Ethernet Vista Ports with Built-in LEDs All of the ports on the switch are 10/100 Mbps Ethernet ports. The network access speed for the ports is automatically sensed and displayed on the front panel by the 100 Mbps LEDs. - Page 5 LEDs This table describes the activity of the Model FS102/FS104/FS108 switch LEDs. Label Color Activity Description Pwr (Power) Green On Power is supplied to the switch. Power is disconnected. Rx/Tx/Collision Green Blinking Packet transmission or reception is occurring on the port.
- Page 6 The Normal/Uplink push button on the front panel of the switch allows you to select uplink (MDI) or normal (MDI-X) wiring for either of the Ethernet ports on the Model FS102 switch, port 4 on the Model FS104 switch, or port 8 on the Model FS108 switch. These ports are configured for normal wiring to connect to a PC when the push button position is out.
- Page 7 Although the examples illustrate specific switches, any of the switches can be used in the network configurations shown. Desktop Switching The Model FS108 switch is used as a desktop switch to build a small network that enables users to have 100 Mbps access to a file server. 100 Mbps...
- Page 8 200 meters. By adding Fast Ethernet switches between hubs, a network is expanded by 200 meters with the addition of each switch. The illustration below shows two NETGEAR Model FE108 Fast Ethernet Hubs integrated with a Model FS108 switch to extend a network.
- Page 9 The Model FS104 Fast Ethernet Switch can be integrated with a NETGEAR Model FE108 Fast Ethernet Hub and a NETGEAR Model DS108 Dual Speed Hub. A full-duplex configurable adapter card installed in the server provides up to 200 Mbps maximum data throughput.
-
Page 10: Prepare The Site
The Normal/Uplink push button eliminates the need to use a crossover twisted pair cable for daisy-chaining or cascading. Use the following guidelines to configure port 1 and port 2 on the Model FS102 switch, port 4 on the Model FS104 switch, or port 8 on the Model FS108 switch for uplink or normal wiring: •... -
Page 11: Verify Installation
When connecting any of the 10/100 Mbps ports on the switch to a hub, set the port to AUTO. The switch must also be set to AUTO when connecting to any device that does not use NWay autonegotiation to detect the operating mode. Setting the toggle switch to AUTO will cause the port to default to half-duplex mode when connecting to a port that does not use autonegotiation. -
Page 12: Troubleshooting Information
LED is off when connected to a full duplex network. Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide Solution Make sure the attached device is powered and there is a proper UTP connection at that end. -
Page 13: Cable And Connector Information
Normal or Crossover MDI-X port twisted pair cable Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide Solution The port and switch might be functioning correctly. However, check the following to make sure that excessive collisions are normal (as in most Ethernet networks) and not caused by: •... - Page 14 Output Transmit Data + Output Transmit Data - 4, 5, 7, 8 Not used Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide 12345678 Uplink Assignment: Port 1 or 2 on the Model FS102 Switch Port 4 on the Model FS104 Switch...
-
Page 15: Technical Specifications
Address database size: Addressing: Queue buffer: 10/100 Mbps ports: 1 MB of buffer space Model FS102, Model FS104, Model FS108 Fast Ethernt Switch Installation Guide Model FS104 Switch Model FS108 Switch ISO/IEC 802-3 (ANSI/IEEE 802.3i) 10BASE-T Ethernet IEEE 802.3u, IEEE802.3x 100BASE-TX, Fast Ethernet 10 Mbps differential Manchester encoded 15.2 W... - Page 16 In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. Certificate of the Manufacturer/Importer It is hereby certified that the NETGEAR Model FS102/104/108 Fast Ethernet Switch has been suppressed in accordance with the conditions set out in the BMPT-AmtsblVfg 243/1991 and Vfg 46/1992.
- Page 17 NETGEAR, Inc. A Bay Networks Company 4401 Great America Parkway Santa Clara, CA 95054 USA Phone: 888-NETGEAR *M-FS100NA-1*...