Table of Contents
Advertisement
QQ
3 7 63 1515 0
TABLE OF CONTENTS
1.
SERVICING NOTES
2.
GENERAL
······································································ 4
3.
3-1. CD door ·············································································· 6
3-2. CD Mechanism Deck ························································· 6
3-3. Front Panel ········································································· 7
3-4. Main Board ········································································· 7
3-5. Key Board ··········································································· 8
3-6. Mech Deck ········································································· 8
3-7. Front Panel (B) ··································································· 9
3-8. Front Board, H/P Board ······················································ 9
Board ················································································ 10
3-10. CD Tray ············································································ 10
3-11. CD Decord Board ····························································· 11
3-12. Base Unit ·········································································· 12
3-13. Cassette Lid (A)/(B) ························································· 12
4.
5.
6.
7.
Tuner CD Section ························································ 19
Main Section ······························································· 20
TE
7-2. Circrit Boards Location ···················································· 21
L 13942296513
7-3. Printed Wiring Board Main Section ······························ 22
7-4. Schematic Diagram Tuner Section ································ 23
7-5. Schematic Diagram Dolby Section ······························· 24
7-6. Schematic Diagram Tape Power Section ······················· 25
7-7. Printed Wiring Board Front Section ······························ 26
7-8. Schematic Diagram Front Section ································· 27
7-9. Printed Wiring Board FLD Section ······························· 28
7-10. Schematic Diagram FLD Section ·································· 29
7-11. Printed Wiring Board CD Section ································· 30
7-12. Schematic Diagram CD Section ···································· 31
7-13. Printed Wiring Board Center/Rear AMP Section ·········· 32
7-14. Schematic Diagram Center/Rear AMP Section ············· 33
7-15. Schematic Diagram Front AMP Section ······················· 34
7-16. Printed Wiring Board Front AMP Section ···················· 35
7-17. IC Block Diagrams ··························································· 36
7-23. IC PIN Function Description ············································ 40
8.
8-1. Cabinet Section ································································· 42
8-2. Front Panel Section-1 ······················································· 43
8-3. Front Panel Section-2 ······················································· 44
8-4. CD Mechanism Deck Section-1 ······································· 45
8-5. CD Mechanism Deck Section-2 ······································· 46
8-6. Base Unit Section (KSM-213ECM) ································· 47
9.
www
.
http://www.xiaoyu163.com
··················································· 3
································································ 13
·························· 14
··························· 14
··································· 48
x
u163
http://www.xiaoyu163.com
SERVICING NOTES
2 9
8
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Q Q
3
6 7
1 3
1 5
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
This appliance is classified as a CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT MARKING is located on
the rear exterior.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
The following caution label is located inside the unit.
co
.
SECTION 1
9 4
2 8
0 5
8
2 9
9 4
2 8
m
9 9
9 9
3
Hide quick links:
Advertisement
Table of Contents
