Specifications - Craftsman 141.142580 Operator's Manual

extension cord:
• Use only3-wire e xtension cords having 3-prong g rounding
type plugs a nd3-pole r eceptacles which a ccept
the tool plug.
• If the extension cord is worn, cut, or damaged in any way,
replace it immediately.
Extension Cord Length (120V Operation)
Wire Size A.W.G,
Up to 25 ft........................................ 14
Up to 50 ft........................................ 12
NOTE:Using extension cords over 50ft. long is not
recommended.
Extension Cord Length (240V Operation)
Wire Size A.W.G.
Up to 50 ft........................................ 18
50to 100 ft ....................................... 16
100to 200 ft ...................................... 14
200 tO 300 ft ..................................... 12
NOTE:Using extension cords over 300ft. long is not
recommended.
ELECTRICAL CONNECTIONS
WARNING: All ele_rical connections must be performed by a
qualified electridan. Make sure tool is off and disconnected from
power source before inspecting any wiring.
The saw is prewired for use on a 120 volti 60Hz power supply.
The power lines are inserted directly onto the switch
The green ground line must remain securely fastened to
the frame to properly protect against electrical shock.
° Remove the key to prevent unauthorized use.
Refer to Figures 43a_57.
The Craftsman 10" Model Number 14258 table saw offers precise
cutting performance for all woods up to 3_4" (8 cm) thick. The
saw is designed for the DIYers and is ruggedly constructed for
continuous service. The 10" Table Saw is recommended for use
with a 10" blade.
The saw features a right extension table with ripping capacity
of 24!._" (62.2 cm). Saw body has on board storage for push stick.,
miter gauge, rip fence and saw blades and blade wrenches. Saw
is equipped with a riving knife and a clear acrylic blade guard
with anti-kickback feature. Cabinet is constructed of plastic and
included a dust extraction port.
Rip Fence Assembly features a preci_on rip fence that is designed
for simple and one-hand maneuverability. Front rail is calibrated
in inches.
Foldable Leg Stand with wheels features an easy transport and
storage.
SPECIFICATIONS
Capacity with 10" Blade:
Depth of cut at 90% ........................ 3W' (8 cm)
Maximum tilt angle of arbor (left) ..................... 45 °
Depth of cut at 45 _ . ....................... 2%_" (5.5 cm)
19
Max. cut right of blade with rip fence ......... 24VJ' (62.2 cm)
Saw Dimensions:
Cabinet depth .......................... 11%2" (29 cm)
Cabinet width .......................... 20_4" (52.7 cm)
Cabinet length ......................... 25%_2" (63.9 cm)
Main table size ................. 24 x 2!'/IJ' (61 x 53.5 cm)
Extension table ............. 56'3AJ' x 21/_÷" (15.2 x 53.5 cm)
Saw Blade:
Blade max. capacity: ..................... 10" (25.4 cm)
Blade arbor .............................. :%" (1.59 cm)
Dado blade max. capacity: ................... _" (1.27 cm)
Saw Constructions:
Cabinet .................................... Plastic
Table .................................. Cast aluminum
Rip fence ........................... Aluminum extrusion
Drive system ................................. By gear
Mitre gauge ................... Cast aluminium with T-rod
Blade guard ............... Acrylic with anti-kickback pawls
Motor .............................. 120 V, 15 A, 60 Hz
No load speed ............................... 4500RPM
Net weight with leg stand ............... 82.5 Ibs (37.5 kg)
Shipping weight ......................... 94.6 Ibs (43 kg)
WARNING: Disconnect power before attempting any of the
following procedures. Be certain switch is in OFF position and
the key is removed. Saw blade must not be moving. Saw blade
will rotate freely after motor is turned off. Allow blade to come
to a complete stop before attempting any of the following
procedures.
WARNING: The operation of any power tool can result in
foreign objects being thrown into the eyes, which can result in
severe eye damage. Always wear safety goggles corn plying
with United States ANSI Z87.1 before commencing power tool
operation.
WARNING: Do not allow familiarity with a toot to make you
careless. Remember that a fraction of a second of carelessness
is sufficient to cause serious injury.
WARNING: Do not use any attachments or accessories that
are not recommended by the manufacturer of this tool. The use
of attachments or accessories that are not recommended can
result in serious personal injury.
WARNING: Although many of the illustrations in this Operator's
Manual are shown with the blade guard removed for clarity, do
not operate the saw with-out the blade guard unless specifically
instructed to do so.
WARNING: The table saw must be mounted to a firm. supporting,
waist high surface_ such as a workbench or leg stand. Many
illustrations in this Operator's Manual are shown with the saw
unmounted for clarity.
APPLICATIONS
You can use this tool for the purposes listed below:
• Straightqine cutting operations, such as crosscutting, ripping,
mitering, beveling, and compound cutting.
• Dado or molding cuts with optional accessories.
• Cabinet making and woodworking
NOTE: This table saw is designed to cut wood and wood
composition products only.