Mode Transition And Structure Of Layers In Service Factory Mode; Structure Of Layers In Service Factory Mode; Structure Of Layers In Panel Factory Mode - Pioneer krp-m01 Service Manual

1
A

Mode transition and structure of layers in Service Factory mode

Mode transition in Service Factory mode
Up
Down
INFORMATION mode
B
1. VERSION (1)
2. VERSION (2)
3. VERSION (3)
4. MAIN NG
5. TEMPERATURE
6. HOUR METER
7. HDMI SIGNAL INFO 1
8. HDMI SIGNAL INFO 2
9. VDEC SIGNAL INFO 1
10. VDEC SIGNAL INFO 2
C PANEL FACTORY mode
1. PANEL INFORMATION
2. PANEL WORKS
3. POWER DOWN
4. SHUT DOWN
5. PANEL-1 ADJ
6. PANEL-2 ADJ
7. PANEL FUNCTION
8. ETC.
9. RASTER MASK SETUP
10. PATTEN MASK SETUP
11. COMBI MASK SETUP

Structure of Layers in Panel Factory Mode 1

D
1. PANEL INFORMATION Version indication of the panel
2. PANEL WORKS Indications of the accumulated power-on time and
power-on count of the panel
3. POWER DOWN Indication of the Power-down history
4. SHUT DOWN Indication of the Shutdown history
5. PANEL-1 ADJ (+)
1. VOL SUS
2. VOL OFFSET
Settings required after replacement of the panel
• • • • •
10. RESET1ST_KSB
• • • • •
Items for factory use
25. SUS FREQ
For AM noise prevention (Depending on the mode,
brightness of the screen changes.)
E
For confirmation of the result of the setting change,
the unit must be turned off then back on again.
6. PANEL-2 ADJ (+)
1. R-HIGH
2. G-HIGH
For the WB adjustment of the panel and ABL
• • • • •
adjustment.
6. B-LOW
A setting table is available for each signal frequency.
7. ABL
7. PANEL FUNCTION (+)
1. R-LEVEL
Items for factory use
• • • • •
To "Structure of Layers in Panel Factory Mode 2"
F
12
1
2
Quick Reference upon Service Visit 2
• To shift to another mode, press [MUTING].
• To shift to another item in a specific mode,
press [i] or [j].
• To shift to the next nested layer below for an
item with a "(+)" indication, press [ENTER/SET].
To return to the next nested layer above,
also press [ENTER/SET].
INITIALIZE mode
1. SIDE MASK LEVEL
2. FINAL SETUP
3. DTB SERVICE MENU
4. Wide XGA AUTO
5. AUTO ADJUSTMENT
OPTION mode
1. CH PRESET
2. Digital AFT
3. SYNC DET
4. CTI
PANEL MAIN FACTORY mode
1. PM NG INFO
2. PM STATE INFO.
3. DP_RX INFO.
4. PM_SETUP
KRP-M01
2
3

Structure of Layers in Service Factory Mode

INFORMATION mode
1. VERSION (1) The software versions for each microcomputer
2. VERSION (2) The Flash memory versions for each device
3. VERSION (3) The software versions for display microcomputer
4. MAIN NG The shutdown message ID/event times
(Going Clear mode by [ENTER/SET] key)
Select Yes by [l] key l pushing and hold [ENTER/SET] key
4-1. CLEAR
5. TEMPERATURE The temperature/FAN rotating status
6. HOUR METER The HOUR METER/P-COUNT information
7. HDMI SIGNAL INFO 1 The information of HDMI information files
8. HDMI SIGNAL INFO 2 The information of HDMI information files
9. VDEC SIGNAL INFO 1 The signal information of VDEC
10. VDEC SIGNAL INFO 2 The signal information of VDEC
PANEL FACTORY mode Refer to [PANEL FACTORY MODE]
PANEL MAIN FACTORY mode
1. PM NG INFO. Shutdown history of the panel main
2. PM STATE INFO. The temperature/FAN rotating status/Room Light Sensor
3. DP_RX INFO. Indication of the DPRx ID
4. PM_SETUP Select the bezel color and clear the shutdown history of
the panel main
OPTION mode
1. CH PRESET For production line use
2. Digital AFT For production line use
3. SYNC DET For technical analysis
4. CTI For technical analysis
INITIALIZE mode
1. SIDE MASK LEVEL For factory use
1-1. SIDE MASK LEVEL
2. FINAL SETUP Set to Factory default settings (it should perform after
2-1. DATA RESET replacing a MAIN Assy)
3. DTB SERVICE MODE Information for the Digital Tuner Service Menu is displayed
3-1. MODE SHIFT
4. Wide XGA AUTO For technical analysis
5. AUTO ADJUSTMENT
Structure of Layers in Panel Factory Mode 2
8. ETC (+)
For transferring backup data (after replacement of
1. BACKUP DATA
the DIGITAL Assy)
2. DIGITAL EEPROM
Change the adjustment status of the DIGITAL Assy.
3. PD INFO.
4. SD INFO.
For clearance of data for the corresponding items.
5. HR-MTR INFO.
The clearing method is the same: Select "CLEAR",
6. PM/B1-B5
then hold [ENTER/SET] pressed for at least 5
7. P COUNT INFO.
seconds.
8. MAX TEMP.
9. MIRROR
Switch the Mirror display mode.
10. CLS Switch the function when checking the color sensor
level.
9. RASTER MASK SETUP (+)
1. MASK OFF For use while the Raster Mask is displayed.
Use [i] or [j] to select the type of mask.
2. RST MASK 01
Use [l] or [k] to select the sequence.
• • • • •
10. PATTERN MASK SETUP (+)
For use while the Pattern Mask is displayed.
1. MASK OFF
Use [i] or [j] to select the type of mask.
2. PTN MASK 01
Use [l] or [k] to select the sequence.
• • • • •
11. COMBI MASK SETUP (+)
1. MASK OFF For use while the Combination Mask is displayed.
Use [i] or [j] to select the type of mask.
2. CMB MASK 01
Use [l] or [k] to select the sequence.
• • • • •
3
4
4