4 ports 10/100/1000base-t and 1 port 1000base-x gigabit ethernet switch with built-in ieee802.3at poe/pse feature and extended operating temperature (2 pages)
Switch to Switch Connection with Fiber Optic cable 3.2 Installing Redundant Fiber Port 3.2.1 Redundant Installation 4. Switching Operation MAC Address Table & Learning Filtering and Forwarding Store and Forward SNMP proxy support 5. Product Specifications 1. Unpacking Information 第 3 頁,共 12 頁 SWH-2109F V1.0...
Page 4
Thank you for purchasing the 9-port SWH-2109F NWay switching hub. Before you start, please check all the contents of this package. The product package should include the following: 1. One 9-port NWay switching hub 2. One external power supply 3. Rubber foot 4.
Twisted pair ports are capable of 10 or 100Mbps auto-negotiation operation (N-Way). 100Mbps according to the 100Base-FX standard are supported on the fiber interface. The SWH-2109F is an ideal solution for micro-segmenting large networks into smaller sub-networks for overall improved performance, so enabling the most demanding bandwidth multimedia and imaging applications.
3 options but only one enable(port based Priority and 802.1P Priority supported and TOS priority supported) QOS support with four traffic classes 2.3 The Front Panel The front panel of the switching hub is shown below. 第 6 頁,共 12 頁 SWH-2109F V1.0...
3. The connecting cable is good and with correct type 4. The connecting device, including any network adapter is functioning. From the Speed LED and Link/Activity, we could judge the connection speed as following: 第 7 頁,共 12 頁 SWH-2109F V1.0...
2.3.3.2 Status LED Reserve 2.3.3.3 Redundancy LED The “Redundancy” LED will be “Green” when the “Redundant “function enable and F1/F2’s with fiber link stage. Redundant F2Link F1 Link F2 Redundancy Green Green F1 Redundancy Green 第 8 頁,共 12 頁 SWH-2109F V1.0...
3. Installing and Using 9 Port NWay Switching Hub 3.1 Installing the 9 Port NWay Switching Hub The SWH-2109F does not require software configuration. Users can immediately use any of the features of this product simply by attaching the cables and turning the power on.
100,000m with multimode or single mode cable. 5.2 Installing Redundant Fiber Port The SWH-2109F built in one pair redundant fiber port function in port F1 and port F2. In the event of a failure in the primary connection (port F2), a fully redundant secondary connection (port F1) is made available to the failed connection.
RJ-45 (100BASE-TX) : UTP Category 5 µ m multimode Fiber Optic :50/125, 62.5/125, or 100/140 µ m single mode 8.3/125, 8.7/125, 9/125 or 10/125 Network Data Rate Auto-negotiation (10Mbps, 100Mbps) Transmission Mode Auto-negotiation (Full-duplex, Half-duplex) 第 11 頁,共 12 頁 SWH-2109F V1.0...
Page 12
240 X 155 X 34 mm Weight 1.1 KG Operating Temperature ~ 50 Storage Temperature ~ 60 Operating Humidity 10% - 90% External Power Adapter AC IN 100~240 V AC, 50/60 Hz AC DC Out 12V DC 1.2A 第 12 頁,共 12 頁 SWH-2109F V1.0...
Need help?
Do you have a question about the swh-2109F and is the answer not in the manual?
Questions and answers