Page 1: Table Of Contents
Picture To adjust sound frequency Size To select sound effect Enjoying stereo and bilingual broadcasts Reveal Hold Stereo programs Cancel Bilingual programs Using other menus Subcode Specification To set clock NEC Service Centres To turn on the TV automatically(wake time)
Page 2: Safeguards
SAFEGUARDS To operate your receiver at the peak performance, please read this Instruction Manual carefully and retain it for the future reference. M Water and Moisture : Never install the set in the following places : in the bathroom, in a wet basement(Dripping or splashing water).
Page 3: Installation
INSTALLATION To connect the aerial Optimum reception of colour requires a good signal and will generally mean that an outdoor aerial must be used. The exact type and positioning of the aerial will depend upon your particular area. Using the ANT(attenuator) switch (See page 6) When visual interference occurs, set the ANT switch to ON using a small screwdriver.
Page 4: Remote Control
STANDBY/ON Under this button pressed once, TV goes to the state of STAND BY. BACK VIDEO 2(SCART JACK) input / output terminal (SCART does not supports S-VIDEO) A/V OUT OF SCART TERMINAL will provide with TV signal output of the selected channel. REMOTE CONTROL MENU TV/AV...
Page 5: Turning The Power On/Off
TURNING THE POWER ON / OFF MThe following describes how to turn the TV on / off using the main switch and the remote control. Turning the power on / off TURNING THE POWER ON / OFF The following describes how to turn the TV on / off using the main switch and the remote control.
Page 6: Edit
EDIT 1. Press the menu button to select INSTALL. 2. Press the C / B buttons and then INSTALL SYSTEM. 3. Select EDIT with the PR y / x buttons and press the C / B buttons to start EDIT. 4.
Page 7: Enjoying Panorama And Zoom Picture
ENJOYING PANORAMA AND ZOOM PICTURE You can enjoy PANORAMA picture and ZOOM 1~ZOOM 4 picture with TV. In addition to regular wide / zoom screen mode. TO SELECT THE PANORAMA OR ZOOM 1~ZOOM 4 SCREEN 1. By pressing the WIDE / ZOOM button in remote control, the following seven modes change cyclically.
Page 8: To Select The Sound Mode
TO SELECT THE SOUND MODE PEECH 1. Press the SELECTABLE SOUND MONO button to select the desired sound quality. - - : - - NORMAL, FAVOURITE, MUSIC, SPEECH can be selected cyclically. 2. Or press the MENU button to select the SOUND and then to be displayed on the right appearance.
Page 9: Enjoying Stereo And Bilingual Broadcasts
ENJOYING STEREO AND BILINGUAL BROADCASTS The unit receivers both stereo and bilingual broadcasts transmitted in either the NICAM or German stereo / bilingual broadcasts system. STEREO PROGRAMS Press the STEREO / BILINGUAL SELECT )button to select to nicam- stereo / mono mode. BILINGUAL PROGRAMS 1.
Page 10: To Turn On The Tv Automatically(Wake Time)
TO TURN ON THE TV AUTOMATICALLY(WAKE TIME) With the CLOCK, the WAKE TIME, the WAKE PR. Preset, the TV will automatically turn on to a preset program number at a reset time. Set the timer ON. Select the WAKE TIME with PR y / x buttons.
Page 11: To Select The Screen Color
TO SELECT THE SCREEN COLOR When no signal is being received, the TV will automatically turn blue or red at the time SCREEN BLUE or SCREEN RED on. 1. Press the MENU button to select the FEATURES and then to be displayed on the right appearance.
Page 12: Watching Picture In Picture
WATCHING PICTURE IN PICTURE The unit is capable of displaying two picture with the small sub picture simultaneously. This is called the Picture-In-Picture function. A TV picture or a picture from external source equipment such as a VTR can be displayed as another picture.
Page 13: To Switch The Main And Sub Picture Of The Pip
TO SWITCH THE MAIN AND SUB-PICTURE OF THE PIP Press the SWAP button when a picture-in-picture is displayed. The main picture(the large picture) and sub-picture(the small picture) are switched. Press the SWAP button again to switch again. TO FREEZE THE SUB-PICTURE Press the STILL button when a sub-picture is displayed.
Page 14: Connecting Video
CONNECTING VIDEO When connecting other equipment, please ensure you turn the main switch OFF to prevent any damage to the equipment. L When connecting the VIDEO to the back of the TV 1. Prepare the connective plug for picture / sound. 2.
Page 15: Connecting With S Picture Video
L Connecting SCART to SCART(STEREO mode is defaulted) 1. Prepare the connective plug for picture / sound. 2. Connect the SCART input/output terminal of VIDEO with the SCART input/output terminal of TV. REAR SCART TERMINAL SCART INPUT/ OUTPUT HI-FI STEREO VIDEO CONNECTING WITH S PICTURE VIDEO When connecting other equipment, please ensure you turn the main switch OFF to prevent any damage to the equipment.
Page 16: Connecting With Audio Set
CONNECTING WITH AUDIO SET When connecting other equipment, please ensure you turn the main switch OFF to prevent any damage to the equipment. MWhen listening to sound in powerful AUDIO, while watching the picture on TV. MConnect external input terminal of AUDIO to right & left sound output of TV signal. RIGHT LEFT CONNECTING DVD PLAYER...
Page 17: Viewing Teletext(Option)/Use Of The Teletext Buttons
VIEWING TELETEXT(OPTION) / USE OF THE TELETEXT BUTTONS M The teletext service is carried on a TV transmission signal, therefore it is only available when a TV program can be received on your TV. Your choice of TV program also governs which Teletext service you will receive. TO SELECT THE TEXT MODE First, turn on your TV SET and choose your TV program.
Page 18: Specification
84A Richmond Rd, Keswick, 5053 Western Australia Perth 45 Sarich Court, Osborne Park 6017 For Service in outer areas, please contact your NEC retailer for the address of the nearest Authorised NEC Service centre. NEC Australia Pty. Ltd. Home Electronics Group...

NEC PF32W503 Instruction Manual

Quick Links

Table of contents

Related Manuals for NEC PF32W503

Summary of Contents for NEC PF32W503