Nec electronics america plasmasync plasma monitor user manual (8 pages)
Summary of Contents for NEC PlasmaSync 3300
Page 1
PlasmaSync 3300 Multimedia Monitor MultiSync is a registered trademark of NEC Technologies, Inc. in the U.S.A. NEC is registered trademark of NEC Corporation. 1993 by NEC Technologies, Inc. PlasmaSync 3300 Multimedia Monitor PlasmaSync NEC Technologies, Inc. 1250 N. Arlington Heights Road, Suite 500...
Page 2
If the unit is damaged in this way the war- ranty will be void. Moreover, there is a serious risk of electric shock. 7. Do not attempt to service or repair the unit. NEC is not liable for any bodily harm or damage caused if unqualified persons attempt ser- vice or open the back cover.
Page 3
Si l’appareil est endommagé de cette manière, la garantie devient caduque. De plus, il y a risque d’électrocution. 7. Ne pas essayer de réparer ou entretenir l’appareil soi-même. NEC ne saura être tenu pour responsable pour toute blessure ou dommage causé par des personnes non qualifiées qui essayent de réparer ou d’ouvrir le...
CONTENTS Introduction ... 1 Introduction to the PlasmaSync 3300 ... 1 Feature Highlights ... 1 Part Names and Functions ... 3 Front View ... 3 Rear View /Terminal Board ... 5 Remote Control Unit ... 11 Battery Installation and Replacement / Remote Control Cautions / Operating Range ... 15 Functions of DIP SW ...
Congratulations on your purchase of NEC' s PlasmaSync 3300 multimedia monitor which includes Microsoft' s Plug and Play compatibility. Just plug your PlasmaSync 3300 monitor into a Plug and Play compatible system, and your monitor is automatically ready to run at it' s optimum performance.
Part Names and Functions Front View VIDEO 1/VIDEO 2/RGB 1/RGB 2/PROCEED/EXIT 1 POWER ... Press to power the monitor on and off. 2 STANDBY /POWER ... Lights green during normal operation. Indicator Lights orange when the monitor is in standby mode.
Terminal Board OPEN “ SHORT OPEN “ SHORT NOTE: When in the EXT. CONTROL mode, the following operations of the supplied remote control are not possible: Power control ON/ OFF, Input selection, and Audio mute ON/OFF. EXTERNAL CONTROL OUT (mini D-SUB 15 PIN)... Connect to a second moni- tor' s EXTERNAL CONTROL input to relay the signal input at the EXTER- NAL CONTROL IN.
Page 8
D VIDEO 2 VIDEO 2 IN (BNC type)...Connect the video source' s output here. S-VIDEO 2 IN...Connect the S-video source with an S-connector output here. THROUGH OUT (BNC type)...Connect to a second monitor' s video input to relay the video signal input at VIDEO 2 IN. THROUGH OUT (S-VIDEO)...Connect to a second monitor' s S-connector input to relay the video signal input at S-VIDEO 2 IN.
Page 9
G RGB 2 R, G, B, H/CS and V IN (BNC)...These are analog RGB input terminals. Connect external components with R, G, B, H/CS, and V output terminals to these analog RGB input terminals. Be sure that the RGB connection cable is correctly attached to the corresponding terminals.
Remote Control Unit ON POWER OFF DEGAUSS VIDEO1VIDEO2 RGB1 RGB2 WIDTH POSITION/CONTROL HEIGHT SIDE PIN SCAN SELECT NORMAL RASTER CONTROL RGB/VIDEO VIDEO CONTRAST BRIGHT COLOR TINT SHARPNESS VISUAL CONTROL NORMAL VOLUME MUTE EXIT PROCEED ON SCREEN MULTIMEDIA MONITOR RD-336E Raster Control 6 POSITION/CONTROL ...
Page 11
ON POWER OFF DEGAUSS VIDEO1VIDEO2 RGB1 RGB2 WIDTH HEIGHT POSITION/CONTROL SIDE PIN SCAN SELECT NORMAL RASTER CONTROL RGB/VIDEO VIDEO CONTRAST BRIGHT COLOR TINT SHARPNESS VISUAL CONTROL NORMAL VOLUME MUTE EXIT PROCEED ON SCREEN MULTIMEDIA MONITOR RD-336E C NORMAL ... This key resets the picture adjustment set- tings of user changeable memory and recalls the factory preset data.
Battery Installation and Replacement The remote control is powered by two 1.5V AA batteries. To install or replace batteries: 1. Turn the remote control unit upside down. 2. Press down on the battery compartment grip and slide the com- partment in the direction of the arrow. 3.
Functions of DIP SW Functions and Settings of DIP SW 1 This DIP switch sets various conditions of the monitor. POWER ON MODE SET No.1 No.2 DIP SWITCH MODE No.3 No.1 No.2 DEFEAT VIDEO 1 VIDEO 2 Pin numbers 4 and 6 are not used. Set the six pins to the OFF position except Nos.
Functions and Settings of DIP SW 2 This DIP switch is used for Sync. Control and Intelligent Power Manager. Set all pins to the OFF position except No. 3 pin during normal operation. No.1 SYNC. CONTROL No.2 MODE AUTO CONTROL (Sep, Comp, Sync on G) MANUAL 1 (Comp.
“HIGH” position. On only the last monitor set it to “75 ” position. NOTE: The connection of three PlasmaSync 3300 monitors or more with THROUGH OUT (VIDEO 1 or 2) terminals may degrade image quality.
2. Set all the 75 /HIGH impedance select switches on all but the last monitor to “HIGH” position. On only the last monitor set all of them to “75 ” position. NOTE: The connection of three PlasmaSync 3300 monitors or more with THROUGH OUT (RGB 1 or 2) terminals may degrade image quality.
NEC MULTISYNC OR PC-COMPATIBLE MONITOR NOTE: •PlasmaSync 3300 does not support PAL/SECAM on a scan converter. •We do not recommend to use a scan converter for NTSC signal. A use of the scan converter degrades picture quality. To EXTERNAL CONTROL...
[b] Connect the right speaker negative (-) wire to RIGHT -. [c] Connect the left speaker negative (-) wire to LEFT -. [d ]Connect the left speaker positive wire (+) to LEFT +. outputs of PlasmaSync 3300 LINE OR LINE OR...
Controls/Adjustments Power 1. Plug in the power cord to an electrical outlet to connect power. 2. Press POWER to turn the monitor on. 3. Press POWER again to turn the monitor off. Press the POWER OFF key on the remote control unit to turn the monitor off when the monitor is turned on.
: indicates direction of adjustment. Controls NEC's new OSM, or On-Screen Manager, System offers the ultimate form of monitor controls. Keys on the remote control unit allow you to easily navigate through menus and adjust controls. As you chose controls, the moving icon shows you what the chosen control will do.
Accessing OSM Press the PROCEED key. Turning off OSM Press the EXIT key when in the main menu ; press the EXIT key twice when in submenus. OSM Menus Main Menu On-Screen Manager' s main menu of Controls gives you an overview of the selection of controls available.
Display Mode Display Mode provides you information about the current resolution display and technical data including the horizontal and vertical frequency. Display Mode Display Mode Mode Mode : 640 x 480 H Freq. : 31.47 kHz Source V Freq. : 60 Hz H Pol.
Visual Controls The Visual controls allow you to adjust the picture controls such as brightness, contrast, color, tint, sharpness and gamma. NOTE: The color, tint, and sharpness controls are not available in the RGB mode and the tint not available in the PAL and SECAM mode. VIDEO Visual Controls Brightness...
External Control Function External Control Port Pin Assignments Pin No. Signal to be connected Not Used 4, 5 INPUT SELECT NO.4 NO.5 INPUT OPEN OPEN VIDEO 1 VIDEO 2 OPEN OPEN RGB 1 RGB 2 Not Used Power ON/OFF Selection 11-14 Not Used NOTE: “GND”...
Page 26
Signal Identification Flowchart Input signal 28 kHz<fH<34 kHz fV<65 Hz 65 Hz<fV 34 kHz<fH<36.5 kHz fV<65 Hz 65 Hz<fV 36.5 kHz<fH<38.6 kHz fV<65 Hz 65 Hz<fV<74Hz 74 Hz<fV 38.6 kHz<fH<42 kHz NOTE: There are other two memory locations for NTSC and PAL than the above. User preset Factory preset : 11...
Troubleshooting Before arranging for service by the NEC Service Center, check the following to be sure repairs are needed. Problem Power cord unplugged. No Picture or Sound Power outlet inactive. Power of external equipment is not ON. External equipment has been incorrectly connected.
Specifications Plasma Screen RGB Input Terminals RGB Output Terminals THROUGH OUT Video Input Terminals VIDEO S-VIDEO Video Output Terminals THROUGH OUT THROUGH OUT (S-VIDEO 1, 2) Audio Input Terminals VIDEO 1, 2 / RGB Audio Output Terminals THROUGH OUT External Control (IN/THROUGH OUT) SOUND Output Internal...
Page 29
Maximum Resolution RGB: 640(H) x 480(V) pixels VIDEO: 400 horizontal lines Signal Bandwidth 33 MHz (maximum) Current Rating AC 120 V, 60 Hz Power Consumption 4.5 A (maximum) Dimensions 31.1(W) x 29.1(H) x5.2 (D) inches/ 788(W) x 738(H) x130(D) mm (Height: 24.5 inches/ 620 mm;...
NEC Technologies, Inc.(hereafter NECTECH)warrants this product to be free from defects in material and workmanship under the following terms. HOW LONG IS THE WARRANTY Parts and labor are warranted for (1) One Year and Plasma display for (1) One year from the date of the first customer purchase.