Download Print this page

NEC MultiSync LCD8205-P User Manual

Nec electronics america multisync user's manual.
Hide thumbs

Advertisement

User's Manual
MultiSync LCD8205
MultiSync LCD8205-P

Advertisement

   Also See for NEC MultiSync LCD8205-P

   Related Manuals for NEC MultiSync LCD8205-P

   Summary of Contents for NEC MultiSync LCD8205-P

  • Page 1

    User’s Manual MultiSync LCD8205 MultiSync LCD8205-P...

  • Page 2: Table Of Contents

    Index Declaration of conformity ... English-1 Important Information ... English-2 Warning, Caution ... English-2 Declaration ... English-2 Safety Precautions, Maintenance & Recommended Use ... English-3 Contents ... English-4 Installation ... English-5 Parts Name and Functions ... English-7 Control Panel ... English-7 Terminal Panel ...

  • Page 3: Declaration Of Conformity

    Declaration of conformity FCC Information 1. Use the attached specified cables with the MultiSync LCD8205 (L828N0)/MultiSync LCD8205-P (L828N0) color display so as not to interfere with radio and television reception. (1) Please use the supplied power cord or equivalent to ensure FCC compliance.

  • Page 4: Important Information

    Voltage 120* *When operating the MultiSync LCD8205/MultiSync LCD8205-P monitor with its AC 125-240V power supply, use a power supply cord that matches the power supply voltage of the AC power outlet being used. NOTE: This product can only be serviced in the country where it was purchased.

  • Page 5: Safety Precautions, Maintenance & Recommended Use

    Safety Precautions, Maintenance & Recommended Use FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTI-FUNCTION MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel.

  • Page 6: Contents

    Contents Your new MultiSync LCD monitor box* should contain the following: • LCD monitor • Power Cord* • Video Signal Cable • Setup Manual • Wireless Remote Control and AAA Batteries • Clamp 15-pin mini D-SUB male to DVI-A DVI-D to DVI-D cable Power Cord* CD-ROM Eyebolt x 2...

  • Page 7: Installation

    Please note the following when mounting on wall or ceiling • When using mounting accessories other than those that are NEC approved, they must comply with the VESA- compatible (FDMlv1) mounting method. • NEC strongly recommends Unit using size M8 screws...

  • Page 8: Attaching Mounting Accessories

    M8 size and 10 - 18 mm in length. If using screws longer than 18 mm, check the depth of the hole. (Recommended Fasten Force: 1125-1375N•cm) NEC recommends using a mounting interface that complies with UL1678 standard in North America. 3. Ventilation Requirements...

  • Page 9: Parts Name And Functions

    Parts Name and Functions Control Panel POWER button ( ) Switches the power on/off. CH +/- button Acts as button to move the highlighted area up or down to select adjustment items within OSD menu. VOL +/- button Increases or decreases audio output level. Increases or decreases the adjustment level within OSD menu settings.

  • Page 10: Terminal Panel

    Terminal Panel HDMI connector To input digital HDMI signals. DVI IN (DVI-I) To input digital or analogue RGB signals from a computer. SPDIF Optical digital audio out for HDMI input only. EXTERNAL CONTROL (D-Sub 9 pin) Connect RS-232C input from external equipment such as a PC in order to control RS-232C functions.

  • Page 11: Wireless Remote Control

    Wireless Remote Control NOTE: The button without explanation doesn’t work. POWER button Switches the power on/off. SOURCE button Enter Input Source OSD menu, [DVI], [PC], [HDMI], [AV1], [AV2], [S-Video] and [Component]. MUTE button Turns on/off mute function. INFO button Turns on/off the information OSD. STILL button Toggles picture status between motion and still image.

  • Page 12: Setup

    C. Replace the cover. CAUTION: Incorrect usage of batteries can result in leaks or bursting. NEC recommends the following battery use: • Place “AAA” size batteries matching the (+) and (-) signs on each battery to the (+) and (-) signs of the battery compartment.

  • Page 13

    5. Switch on the power of all the attached external equipment When connected with a computer, switch on the power of the computer first. 6. Operate the attached external equipment Display the signal from the desired input source. 7. Adjust the sound Make volume adjustments when required.

  • Page 14: Connections

    Connections Before making connections: First turn off the power of all the attached equipment and make connections. Refer to the user manual included with each separate piece of equipment. Connecting a Personal Computer Connecting your computer to your LCD monitor will enable you to display your computer’s screen image. Some video cards and a pixel clock over 162MHz may not display an image correctly.

  • Page 15: Connecting A Dvd Player With Component Out

    Connecting a DVD Player with component out Connecting your DVD player to your LCD monitor will enable you to display DVD video. Refer to your DVD player user’s manual for more information. Connect the LCD Monitor to a DVD Player •...

  • Page 16: Connecting A Dvd Player With Hdmi Out

    Connecting a DVD Player with HDMI out Connecting your DVD player to your LCD monitor will enable you to display DVD video. Refer to your DVD player user’s manual for more information. Connect the LCD Monitor to a DVD Player •...

  • Page 17: Basic Operation

    Basic Operation Power ON and OFF Modes The LCD monitor power indicator will turn green while powered on and will turn red while powered off. Power Button English-15...

  • Page 18: Power Indicator

    Power Indicator Mode Power ON Green Power OFF (Standby)* Power consumption under 1W Power Save Red blinking Power consumption under 15W Not connected Green blinking * When in Power OFF (Standby) mode, RS-232C control do not function. Using Power Management The LCD monitor follows the VESA approved DPM Power Management function.

  • Page 19: Osd (on-screen-display) Controls

    OSD (On-Screen-Display) Controls NOTE: Some functions may not be available depending on the model or optional equipment. Main Menu Item Main Menu Icons Press MENU button to show OSD menu. Remote Control Press MENU button to show OSD menu. Control Panel Key Guide Press UP and DOWN Press Right button to...

  • Page 20: Picture

    Setting Picture Picture Mode User Dynamic Standard Movie Mild User Brightness Contrast Color (AV1/AV2/S-Video/Component) Tint (AV1/AV2/S-Video/Component) Sharpness Phase (Component) Color Temp User (PC, DVI, HDMI) Cool 2 Cool 1 Normal Warm 1 Warm 2 Size 16:9 Panorama (HDMI/AV1/AV2/S-Video/Component) Zoom1 (HDMI/AV1/AV2/S-Video/Component) Zoom2 (HDMI/AV1/AV2/S-Video/Component) 14:9...

  • Page 21: Sound

    Sound Mode User This function use setting Equalizer value. Standard Selection of preset Sound mode (Equalizer). Music Movie Speech Volume Adjust the sound volume level. Balance Tuning the sound balance between left and right. Equalizer 10 KHz The value of 5 Band equalizer are preset. 3 KHz These values are changed by user with user mode setting.

  • Page 22

    Advanced Dimming Auto Dimming Enable/Disalbe Auto Dimming control by Abient Light sensor. Dim Level Display current Dim Level. MAX Dim Ambient Adjusts detected light ambient to set the maximun dimming. MIN Dim Ambient Adjusts detected light ambient to set the minimun dimming. Ambient Display current detected light ambient level by Lux unit.

  • Page 23: Controlling The Lcd Monitor Via Rs-232c Remote Control

    Controlling the LCD monitor via RS-232C Remote Control This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal. Functions that can be controlled by a personal computer are: • Power ON or OFF • Switching between input signals Connection LCD Monitor + PC PC (Out)

  • Page 24: Features

    Allows for the monitor to be mounted on a wall or an arm using any third party compliant device. NEC recommends using mounting interface that comply with TÜV-GS and/or UL1678 standard in North America.

  • Page 25: Troubleshooting

    NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.

  • Page 26: Specifications

    Specifications Product Specifications LCD Module Design View Distance: Frequency Pixel Clock Viewable Size Input Signal DVI-I DVI-I HDMI HDMI Connector AV1/AV2 S-VIDEO Mini DIN 4pin COMPONENT RCA (Y, Cb/Pb, Cr/Pr) AUDIO AUDIO Input STEREO Mini Jack RCA(L/R) x3 HDMI Connector AUDIO Output SPDIF Connector Speaker Output...

  • Page 27: Pin Assignment

    Pin Assignment 1) S-VIDEO input: VIDEO Pin No Name Y (Luminance) C (Chroma) 2) Digital/Analog RGB input: DVI-I Pin - Assignment of DVI connector: TX2- TX1- TX2+ TX1+ Shield (TX2 / TX4) Shield (TX1 / TX3) DDC-Serial Clock +5V power DDC-Serial Data Ground Hot plug detect...

  • Page 28: Manufacturer's Recycling And Energy Information

    Manufacturer’s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally- friendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).

This manual also for:

Multisync lcd8205

Comments to this Manuals

Symbols: 0
Latest comments: