NEC MultiSync LCD2070NX User Manual
Nec multisync user's manual
Hide thumbs
Also See for MultiSync LCD2070NX:
- User manual (122 pages) ,
- Brochure & specs (4 pages) ,
- Specification sheet (2 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for NEC MultiSync LCD2070NX
Summary of Contents for NEC MultiSync LCD2070NX
- Page 1 MultiSync LCD2070NX MultiSync LCD2070VX User’s Manual...
-
Page 2: Table Of Contents
Declaration of Conformity ... English-2 Contents ... English-3 Quick Start ... English-4 Controls ... English-8 Recommended use ...English-10 Specifications for MultiSync LCD2070VX ... English-12 Specifications for MultiSync LCD2070NX ... English-13 Features ...English-14 Troubleshooting ...English-15 TCO’03 ...English-16 Manufacturer’s Recycling and Energy Information ... English-17... -
Page 3: Warning, Caution
Therefore, it should be read carefully in order to avoid any problems. Caution: When operating the MultiSync LCD2070NX and LCD2070VX with a 220-240V AC power source in Europe, use the power cord provided with the monitor. In the UK, a BS approved power cord with a moulded plug has a Black (five Amps) fuse installed for use with this equipment. -
Page 4: Canadian Department Of Communications Compliance Statement
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1. FCC Information Use the attached specified cables with the MultiSync LCD2070NX/LCD2070VX (L204FY) colour monitor so as not to interfere with radio and television reception. -
Page 5: Contents
Contents Your new NEC MultiSync LCD monitor box* should contain the following: • MultiSync LCD monitor with tilt/swivel/height adjust stand • Power Cord • Cable cover • Video Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male) •... -
Page 6: Quick Start
7. Place the D-Sub and the USB cable into the specific hooks indicated in Figure C.2 (USB Cable: NX model only). Highest Stand Position Input1 (DVI) DC-OUT Figure C.1 Power Cord (Picture: LCD2070NX model) Figure A.2 30˚ Tilt Power Cord DVI Cable Input2 (D-Sub) (NX model only) English-4 Macintosh Figure B.1... - Page 7 NOTE: If you have any problems, please refer to the Troubleshooting section of this User’s Manual. Figure E.1 USB Cable D-Sub Cable (NX model only) Figure C.3 (Picture: LCD2070NX model) OFF Position ON Position Vacation Switch Power Button English-5 Flat Figure D.2...
-
Page 8: Raise And Lower Monitor Screen
Raise and Lower Monitor Screen The monitor may be raised or lowered. To raise or lower screen, place hands on each side of the monitor and lift or lower to the desired height (Figure RL.1). NOTE: Handle with care when raising or lowering the monitor screen. Tilt and Swivel Grasp both sides of the monitor screen with your hands and adjust the tilt and swivel as desired (Figure TS.1). -
Page 9: Flexible Arm Installation
100mm 100mm Figure F.1 Figure S.4 Thickness of Bracket (Arm) 2.0~3.2mm 4 Screws (4M) (Max Depth: 14mm) Weight of LCD assembly: 5.7 kg - LCD2070NX (MAX) (Picture: LCD2070NX model) English-7 5.8 kg - LCD2070VX (MAX) -
Page 10: Controls
Active Auto Adjust function. Enter the OSM sub menu. RESET/DV MODE Resets the highlighted control menu to the factory setting. Enters the DV Mode (LCD2070NX model only). NOTE: When RESET is pressed in the main and sub-menu, a warning window will appear allowing you to cancel the RESET function by pressing the MENU/EXIT button. -
Page 11: Menu Tools
Colour Control System Colour Control System: Six colour presets select the desired colour setting (sRGB and NATIVE colour presets are standard and cannot be changed). R,G,B: Increases or decreases Red, Green or Blue colour depending upon which is selected. The change in colour will appear on screen and the direction (increase or decrease) will be shown by the bars. -
Page 12: Recommended Use
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. - Page 13 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen.
-
Page 14: Specifications For Multisync Lcd2070Vx
Specifications for MultiSync LCD2070VX Monitor Specifications LCD Module Diagonal: 51 cm/20.1 inches Viewable Image Size: 51 cm/20.1 inches Native Resolution (Pixel Count): 1600 x 1200 Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync.TTL Level Display Colours Viewing Angle Left/Right: 80°/80°... -
Page 15: Specifications For Multisync Lcd2070Nx
Specifications for MultiSync LCD2070NX Monitor Specifications LCD Module Diagonal: 51 cm/20.1 inches Viewable Image Size: 51 cm/20.1 inches Native Resolution (Pixel Count): 1600 x 1200 Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync.TTL Level Display Colours Viewing Angle Left/Right: 88°/88°... -
Page 16: Features
Features Thin-frame design creates more desktop space for you to work and play, while the flat screen’s crisp, bright images and crystal- clear text deliver a comfortable viewing experience. No Touch Auto Adjust automatically adjusts your optimal image settings upon initial power-on. Colour Control System allows you to change between six colour settings on your display to match your personal preference. -
Page 17: Troubleshooting
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. -
Page 18: Tco'03
TCO’03 Some of the features of the TCO’03 Display requirements: Ergonomics • Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability. Energy •... -
Page 19: Manufacturer's Recycling And Energy Information
Manufacturer’s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally- friendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).