NEC MultiSync LCD2060NX User Manual
Nec monitor user's manual multisync lcd2060nx
Hide thumbs
Also See for MultiSync LCD2060NX:
- Dimensional drawing (2 pages) ,
- User manual (44 pages) ,
- User manual (92 pages)
Related Manuals for NEC MultiSync LCD2060NX
Summary of Contents for NEC MultiSync LCD2060NX
- Page 1 MultiSync LCD2060NX User’s Manual...
-
Page 2: Declaration Of The Manufacturer
Therefore, it should be read carefully in order to avoid any problems. Caution: When operating the MultiSync LCD2060NX with a 220-240V AC power source in Europe, use the power cord provided with the monitor. In the UK, a BS approved power cord with a moulded plug has a Black (five Amps) fuse installed for use with this equipment. -
Page 3: Canadian Department Of Communications Compliance Statement
Ce produit porte la marque ‘C-UL’ et se conforme aux règlements de sûrele Canadiens selon CAN/CSA C22.2 No. 60950. FCC Information Use the attached specified cables with the MultiSync LCD2060NX colour monitor so as not to interfere with radio and television reception. -
Page 4: Quick Start
Contents Your new NEC MultiSync LCD monitor box* should contain the following: • MultiSync LCD2060NX monitor with tilt base • Power Cord • Video Signal Cable (DVI-D to DVI-D cable) • Video Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male) •... -
Page 5: Figure A
Macintosh Figure A.1 Figure A.2 Figure B.1 Cable Adapter (not included) INPUT1 INPUT2 INPUT1 INPUT2 Figure C.1 Figure C.2 Vacation Switch Power Button Figure D.1 English-4... - Page 6 Raise and Lower Monitor Screen The monitor may be raised or lowered. To raise or lower screen, place hands on each side of the monitor and lift or lower to the desired height (Figure RL.1). Note: Handle with care when raising or lowering the monitor screen. Tilt and Swivel Grasp both sides of the monitor screen with your hands and adjust the tilt and swivel as desired (Figure TS.1).
-
Page 7: English
NOTE: This LCD monitor is designed for use with a flexible arm. Please use the attached screws (4pcs) when mounting. To meet the safety requirements the monitor must be mounted to an arm which guaranties the necessary stability under consideration of the weight of the monitor. The LCD monitor shall only be used with an approved arm (e.g. GS mark). -
Page 8: English
Controls OSM (On-Screen-Manager) Controls The OSM controls on the front of the monitor function as follows: To access OSM press any of the control buttons (<, >, -, +, EXIT). To change signal input, press the SELECT button. NOTE: OSM must be closed in order to change signal input. Control Menu EXIT... -
Page 9: English
FINE Improves focus, clarity and image stability by increasing or decreasing this setting. Should the “Auto Adjust function” and the “H.Size” function do not give you a satisfactory picture setting, a fine tuning can be performed using the “Fine” function. It improves focus, clearity and image stability by increasing or decreasing this setting. -
Page 10: Hot Key
Tools 2 LANGUAGE OSM control menus are available in seven languages. OSM LEFT/RIGHT You can choose where you would like the OSM control image to appear on your screen. Selecting OSM Location allows you to manually adjust the position of the OSM control menu left or right. -
Page 11: Recommended Use
NOTE: As with all personal display devices, NEC-Mitsubishi Electronics Display-Europe recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. - Page 12 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen.
-
Page 13: Specifications
In flat panel technologies, each dot on the screen is actually one pixel, so to expand resolutions to full screen, an interpolation of the resolution must be done. *2 NEC-Mitsubishi Electronics Display cites recommended resolutions at 60 Hz for optimal display performance. NOTE: Technical specifications are subject to change without notice. - Page 14 FullScan Capability: Allows you to use the entire screen area in most resolutions, significantly expanding image size. NaViSet : Is a ground-breaking software family, developed by NEC-Mitsubishi, providing intuitive access to all monitor setting controls and remote diagnosis via the Windows interface, based upon the VESA standard, DDC/CI. Using a standard VGA or...
-
Page 15: Troubleshooting
NOTE: As with all personal display devices, NEC-Mitsubishi Electronics Display-Europe recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. Image is unstable, unfocused or swimming is apparent •... - Page 16 TCO’03 Some of the features of the TCO’03 Display requirements: Ergonomics • Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability. Energy •...
- Page 17 ISO (International Organisation for Standardization) and TCO (Swedish Trades Union). For more information, and for help in recycling your old NEC or Mitsubishi monitors, please visit our website at http://www.nec-mitsubishi.com (in Europe) or http://www.nmv.co.jp/environment (in Japan) or...