NEC MultiSync LCD175VXM+ User Manual
Lcd
Hide thumbs
Also See for MultiSync LCD175VXM+:
- User manual (46 pages) ,
- Specifications (2 pages) ,
- User manual (18 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for NEC MultiSync LCD175VXM+
Summary of Contents for NEC MultiSync LCD175VXM+
- Page 1 MultiSync LCD175VXM+ MultiSync LCD195VXM+ User’s Manual...
-
Page 2: Declaration Of The Manufacturer
NERGY endorsement of any product or service. ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy, Norway, Spain, Sweden, U.K.. IBM PC/XT/AT, PS/2, MCGA, VGA, 8514/A and XGA are registered trademarks of International Business Machines Corporation. -
Page 3: Canadian Department Of Communications Compliance Statement
Tel. No.: Type of Product: Equipment Classification: Model: Non shield type, 3-conductor 1.8 m U.S.A NEC Display Solutions of America, Inc. 500 Park Blvd, Suite 1100 Itasca, Illinois 60143 (630) 467-3000 Display Monitor Class B Peripheral MultiSync LCD175VXM+ (L174F1) MultiSync LCD195VXM+ (L194F2) We hereby declare that the equipment specified above conforms to the technical standards as specified in the FCC Rules. -
Page 4: Quick Start
Contents Your new NEC MultiSync LCD monitor box* should contain the following: • MultiSync LCD monitor with tilt base • Audio Cable • Power Cord • Video Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male) • Video Signal Cable (DVI-D to DVI-D) (LCD195VXM+ only) •... -
Page 5: Raise And Lower Monitor Screen
3. To attach the Cable management cover: Insert the tabs of the Cable management cover into the holes of Stand neck and slide the Cable management cover downward into place (Figure A.4). NOTE: Please confirm that the tabs are completely secure. 4. -
Page 6: Remove Monitor Stand For Mounting
Remove Monitor Stand for Mounting To prepare the monitor for alternative mounting purposes: 1. Disconnect all cables. 2. Place monitor face down on a non-abrasive surface (Figure R.1). 3. Remove the 4 screws connecting the monitor to the stand and remove the stand as indicated (Figure R.2). The monitor is now ready for mounting in an alternative manner. - Page 7 Controls OSM (On-Screen Manager) control buttons on the front of the monitor function as follows: 1. Basic function at pressing each key SELECT Button At No OSD Showing OSM. showing At OSD showing Go to Adjustment stage. (Icon selection stage) At OSD showing Go to Icon selection stage.
- Page 8 AUDIO Control the sound volume of speakers and headphone. To mute the speaker sound, press the 1<->2/RESET key. BRIGHTNESS Adjusts the overall image and background screen brightness. CONTRAST Adjusts the image brightness in relation to the background. AUTO CONTRAST (Analog Input only) Adjusts the image displayed for non-standard video inputs.
-
Page 9: Monitor Info
OSM LOCK OUT This control completely locks out access to all OSM control functions without Brightness and Contrast. When attempting to activate OSM controls while in the Lock Out mode, a screen will appear indicating the OSM are locked out. To activate the OSM Lock Out function, press “1<->2/ RESET”, then “+” key and hold down simultaneously. -
Page 10: Recommended Use
As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. - Page 11 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen.
- Page 12 Specifications for MultiSync LCD175VXM+ Monitor Specifications LCD Module Diagonal: 43 cm/17 inches Viewable Image Size: 43 cm/17 inches Native Resolution (Pixel Count): 1280 x 1024 Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync.TTL Level (Positive/Negative) Display Colours Analog input: 16,7 M Synchronization Range Horizontal: 31.5 kHz to 81.1 kHz Vertical: 56 Hz to 76 Hz...
- Page 13 Specifications for MultiSync LCD195VXM+ Monitor Specifications LCD Module Diagonal: 48 cm/19 inches Viewable Image Size: 48 cm/19 inches Native Resolution (Pixel Count): 1280 x 1024 Input Signal Video: ANALOG 0.7 Vp-p/75 Ohms Sync: Separate sync.TTL Level (Positive/Negative) Display Colours Analog input: 16,7 M Synchronization Range Horizontal: 31.5 kHz to 81.1 kHz Vertical: 56 Hz to 76 Hz...
- Page 14 Features Reduced Footprint: Provides the ideal solution for environments requiring superior image quality but with size and weight limitations. The small footprint and low weight allow it to be moved or transported easily from one location to another. Colour Control System: Allows you to adjust the colours on your screen and customize the colour accuracy of your monitor to a variety of standards.
-
Page 15: Troubleshooting
As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. - Page 16 TCO’03 Some of the features of the TCO’03 Display requirements: Ergonomics • Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability. Energy •...
-
Page 17: Energy Saving
Manufacturer’s Recycling and Energy Information NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally- friendly products, and always strive to help define and comply with the latest independent standards from agencies such as ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).