NEC SpectraView 2690 User Manual page 23

Tag6 Color Control
Tag7 Sharpness
DVI Selection
HDCP CONTENT
(Digital Input Only)
Video Detect
Off Timer
IPM (Intelligent Power
Manager)
IPM Setting
Colour Control Systems: Seven preset colour settings.
For preset settings 1, 2, 3 and 5, the following levels can be adjusted:
TEMPERATURE: Adjust the white temperature by increasing or decreasing this setting.
A lower colour temperature will make the screen reddish and a higher colour temperature
will make the screen bluish.
WHITE (White Balance): If TEMPERATURE needs further adjustment; the individual
R/ G/ B/ levels of the white point can be adjusted. To adjust the R/G/B levels, CUSTOM
must be showing as the TEMPERATURE selection.
HUE: Adjusts the hue of each colour*
the menu colour bars will show the amount of adjustment.
SATURATION: Adjusts the colour depth of each colour*
the colour vividness increases.
OFFSET: Adjusts the colour brightness of each colour*
colour Brightness increases.
*1: RED, YELLOW, GREEN, CYAN, BLUE and MAGENTA.
NATIVE, sRGB: Original colour presented by the LCD panel that is unadjustable.
PROGRAMMABLE: The colour tone that was set up with the downloaded application
software is reflected.
This is a digital capability for keeping a crisp image at all signal timings. It continuously
adjusts to maintain a distinct or soft image as you prefer, and is set independently
according to different timings. Press "Left" or "Right" to adjust.
This function selects the DVI input mode. When the DVI selection has been changed, you
must restart your computer. Press "Left" or "Right" to select.
AUTO: By using the DVI-D to DVI-D cable, the DVI SECTION is DIGITAL.
By using the D-SUB to DVI-A cable, the DVI SECTION is ANALOG.
DIGITAL: DVI digital input is available.
ANALOG: DVI analog input is available.
Selects the type of input to be used with HDCP CONTENT.
OFF: When a PC or other computer equipment is connected, select "OFF".
ON: When a DVD player or other type of high definition device is connected, select "ON".
Note: Interlaced signals (480i, 576i, 1080i) are not supported. If you have any problems,
please refer to the Troubleshooting section of this User's Manual.
Selects the method of video detection when more than one computer is connected.
Press "Left" or "Right" to select.
FIRST: The video input has to be switched to "FIRST" mode. When current video input
signal is not present, then the monitor searches for a video signal from the other video
input port. If the video signal is present in the other port, then the monitor switches the
video source input port to the new found video source automatically. The monitor will not
look for other video signals while the current video source is present.
LAST: The video input has to be switched to the "LAST" mode. When the monitor is
displaying a signal from the current source and a new secondary source is supplied to the
monitor, then the monitor will automatically switch to the new video source. When current
video input signal is not present, then the monitor searches for a video signal from the
other video input port. If the video signal is present in the other port, then the monitor
switches the video source input port to the new found video source automatically.
NONE: The Monitor will not search the other video input port unless the monitor is
turned on.
Monitor will automatically turn off after the preset time period from power on with the
ON/OFF function. When you select "ON", press "SELECT" and "Left" or "Right" to adjust.
Before powering off, a message will appear on the screen asking the user if they want to
delay the turn off time by 60 minutes. Press any OSM button to delay the turn off time.
The Intelligent Power Manager allows the monitor to enter into a power saving mode after
a period of inactivity. The IPM has three settings.
OFF: Monitor does not go into power save mode when the input signal is lost.
STANDARD: Monitor enters power save mode automatically when the input signal is lost.
OPTION: Monitor enters power save mode automatically when the amount of surrounding
light goes below the level that is determined by the user.
Adjusts the ILLUMINANCE value for IPM.
English-21
1
. The change in colour will appear on screen and
1 . Press the "RIGHT" button and
1 . Press "RIGHT" button and the