Sony cdx-gt650ui Operating Instructions Manual page 33

Fm/am compact disc player
Hide thumbs Also See for cdx-gt650ui:
Table of Contents

Advertisement

4-193-832-11(1)
FM/AM
Compact Disc Player
Installation/Connections
Installation/Connexions
CDX-GT650UI
©2010 Sony Corporation Printed in Thailand
× 2
× 4
Equipment used in illustrations (not supplied)
Appareils utilisés dans les illustrations (non fournis)
Front speaker
Active subwoofer
Haut-parleur avant
Caisson de graves actif
Rear speaker
Power amplifier
Haut-parleur arrière
Amplificateur de puissance
A
FRONT
AUDIO OUT
SUB OUT ( MONO )
REAR
AUDIO OUT
B
BUS AUDIO IN
Satellite radio tuner
(XM/SIRIUS)*
Syntoniseur radio satellite
(XM/SIRIUS)*
* not supplied
non fourni
BUS CONTROL IN
Cautions
Connection example
This unit is designed for negative ground (earth) 12 V
Notes (
-A)
DC operation only.
Be sure to connect the ground (earth) lead before connecting the
Do not get the leads under a screw, or caught in moving
amplifier.
The alarm will only sound if the built-in amplifier is used.
parts (e.g. seat railing).
Before making connections, turn the car ignition off to
Note on satellite radio tuner (
-B)
avoid short circuits.
This unit does not support the XM radio tuner
Connect the yellow and red power supply leads only
XMDSON100.
after all other leads have been connected.
Run all ground (earth) leads to a common ground
(earth) point.
Connection diagram
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
To a metal surface of the car
The use of optical instruments with this product will
First connect the black ground (earth) lead, then connect the yellow
increase eye hazard.
and red power supply leads.
Notes on the power supply lead (yellow)
To the power antenna (aerial) control lead or
When connecting this unit in combination with other
power supply lead of antenna (aerial) booster
stereo components, the connected car circuit’s rating
Notes
must be higher than the sum of each component’s fuse.
It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
When no car circuits are rated high enough, connect
manually-operated telescopic antenna (aerial).
the unit directly to the battery.
When your car has a built-in FM/AM antenna (aerial) in the rear/
side glass, see “Notes on the control and power supply leads.”
To AMP REMOTE IN of an optional power
Parts Iist
amplifier
This connection is only for amplifiers. Connecting any other system
may damage the unit.
The numbers in the list are keyed to those in the
To the interface cable of a car telephone
instructions.
The bracket
and the protection collar
are
To a car’s illumination signal
attached to the unit before shipping. Before mounting
Be sure to connect the black ground (earth) lead to a metal surface
of the car first.
the unit, use the release keys
to remove the bracket
To the +12 V power terminal which is energized
from the unit. For details, see “Removing the
in the accessory position of the ignition switch
protection collar and the bracket (
)” on the reverse
Notes
side of the sheet.
If there is no accessory position, connect to the +12 V power
Keep the release keys
for future use as they are
(battery) terminal which is energized at all times.
also necessary if you remove the unit from your
Be sure to connect the black ground (earth) lead to a metal
car.
surface of the car first.
When your car has a built-in FM/AM antenna (aerial) in the rear/
Caution
side glass, see “Notes on the control and power supply leads.”
Handle the bracket
carefully to avoid injuring your
To the +12 V power terminal which is energized
fingers.
at all times
Be sure to connect the black ground (earth) lead to a metal surface
of the car first.
Catch
Note
Before installing, make sure that the catches on both sides of the bracket
are bent inwards 2 mm (
/
in). If the catches are straight or bent
3
32
outwards, the unit will not be installed securely and may spring out.

Advertisement

Table of Contents
loading

Table of Contents