Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for NComputing VIRTUAL DESKTOP KIT U170
Summary of Contents for NComputing VIRTUAL DESKTOP KIT U170
-
Page 1: User Manual
USB Virtual Desktop Kit (Model U170) with vSpace User Manual ncomputing.com... -
Page 2: Important Notices
Microsoft or as expressly set forth in the “Microsoft Windows Server to Windows XP License Rights” section of the NComputing EULA. In all cases, your rights and obligations with respect to the use of vSpace software with Windows Server software and Windows Client software are defined by both the NComputing vSpace software EULA and the applicable Microsoft Software License Agreement or EULA. -
Page 3: Table Of Contents
INSTALLING THE HARDWARE ... 9 ... 9 ONNECTING ERIPHERAL EVICES ... 10 ONNECTION PTIONS ... 11 OUNTING AND ECURITY NCOMPUTING VSPACE SOFTWARE INSTALLATION ... 12 ... 14 ETUP PRODUCT REGISTRATION... 15 ... 15 NLINE EGISTRATION ... 16 FFLINE EGISTRATION HECKING... -
Page 4: Safety Information
Safety Information Refer to the following information to prevent any physical injury or loss of assets caused by damage to the product. A user must read this user manual carefully before use and properly follow the instructions. Make sure that the place of installation is not too hot (above 35˚C), too cold (below 0˚C) or too wet (above 85% relative humidity). -
Page 5: Regulatory Compliance
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. KCC Certification Information NComputing U170 1.기기의명칭(모델명): USB-based Expansion kit (U170) 2.인증받은 자의 상호: 엔컴퓨팅 주식회사 3.제조자/제조국가: Magic Control Technology Corporation/대만... -
Page 6: Product Overview
USB Virtual Desktop (Model U170) User Manual Product Overview The NComputing U170 kit enables users to dramatically cut computing costs by sharing the untapped power of existing computers. The U170 access device and NComputing vSpace software work together to efficiently harness excess computing capacity and enable multiple users to share a single computer. -
Page 7: Minimum System Requirements
Notices section at the beginning of this document. Almost any modern PC can be used to host NComputing vSpace software. The guidelines below are a good rule of thumb for determining how many users you can provision on a host PC and expect to have a native experience running general productivity software applications. -
Page 8: Access Devices
Vendor Chipset SB710 Broadcom HT1100 Intel ICH8 Intel ICH9 Intel ICH10 nVIDIA ION Series * Note: This is NOT a comprehensive list of chipsets that have more than one USB bus. Access Devices For each U170 station, you will need: ... -
Page 9: Installing The Hardware
Installing the Hardware This section shows how to connect a U170 device to peripheral equipment and to a host Connecting Peripheral Devices Refer to the illustrations below for information on the ports used to connect the U170 to peripherals and to a host PC. The U170 has two USB 2.0 connectors to support USB devices. -
Page 10: Connection Options
Note: The U170 device is powered by the USB bus and a single USB port can provide power for only one U170 device with a mouse and keyboard. Adding additional USB devices immediately downstream of the U170 that draw too much power is likely to cause errors. -
Page 11: Mounting And Security
Note: Performance may be impacted by poor quality cables or hubs. We recommend using USB 2.0-certified cables with minimum wires sizes of AWG 24 (power) and 28 AWG (signal). (Note: the higher the number, the smaller the wire.) Mounting and Security Using two screws (provided) you can attach the U170 to the back of an LCD monitor that has VESA-compliant mounting holes, as shown below. -
Page 12: Ncomputing Vspace Software Installation
IMPORTANT! Per the instructions below, always check the NComputing website for the latest vSpace software. The software on the CD in your package may not be the latest version. - Page 13 6. The next screen in the hardware wizard will show that the operating system has identified the U170 device and will display the prompt “What would you like the wizard to do?” Click “Install the software automatically [Recommended].” 7. The next screen of the hardware installation wizard is a warning message. Click “Continue Anyway.”...
-
Page 14: User Setup
9. Repeat these steps for each U170 device connected to the system. Note: The monitor on the host PC will flash on and off during the video driver installation. This will occur for each new U170 being installed. User Setup There are two options for setting up users on a multi-user system: 1. -
Page 15: Product Registration
The U170 USB virtual desktop and vSpace software that you install on the host PC must be registered with NComputing. Prior to registration, user sessions will be limited to 60 minutes before timing out and requiring a reboot of the system. -
Page 16: Offline Registration
4. If you select the option to use the online registration option, you will connect to the NComputing registration service. You may select the “Register future devices in the background” option so that any time you install a new U170 to the system, the License wizard will discover and register the product with your information without any user intervention. -
Page 17: Displaying Information About The Vspace Software
2. Click the “Connect” button. A message will be displayed to inform you if an update is available. If an update is available, follow the on-screen prompts to update the vSpace software. Displaying Information About the vSpace Software You can display information about the vSpace software installed on the host PC. The information includes the following: ... -
Page 18: Uninstalling Vspace
Additional Features Auto-Login NComputing vSpace software has a convenient auto-login feature popular in schools, kiosks or digital-signage applications. When this option is enabled, once the host PC boots, each U170 station will automatically log in using the username and password defined for users under Windows Server. -
Page 19: Setting The Display Resolution
To enable the auto-login feature: 1. Right-click on the NCTray icon on the desired station and then click on Auto- Login Setup. The Auto Logon Setup dialog box will be displayed. 2. Enter a username and password combination defined for users under Windows Server;... -
Page 20: Sending Messages
Sending Messages You can send messages from one station to other stations or from the host PC to the stations connected to it. To send a message: 1. At either a station or at the host PC, right-click on the NCTray icon in the System Tray and select Send Message. -
Page 21: Troubleshooting
Remember that the OS and host PC are supporting more users and additional boot time is required. For more troubleshooting information, visit the NComputing Knowledge Base in the Support section of the NComputing website, at www.ncomputing.com. - Page 22 © 2003-2011 NComputing Inc. All rights reserved. NComputing and vSpace are registered trademarks of NComputing Inc. – USA. Microsoft and Windows are registered trademarks of Microsoft Corporation. All trademarks are the property of their respective owners.
Need help?
Do you have a question about the VIRTUAL DESKTOP KIT U170 and is the answer not in the manual?
Questions and answers
dear sir i want software of u170 ncomputing deivice , please send setup file at ks210666@gmail.com
You can obtain the software setup file for the NComputing VIRTUAL DESKTOP KIT U170 by visiting the NComputing Software Download Center at the provided website. If you do not have internet access, you can use the CD installer.
This answer is automatically generated