Bosch GOP 10,8 V-LI Professional Original Instructions Manual page 15

OBJ_BUCH-630-007.book Page 15 Monday, January 7, 2013 10:59 AM
Intended Use
The machine is intended for sawing and cutting wooden mate-
rials, plastic, gypsum, non-ferrous metals and fastening ele-
ments (e. g., unhardened nails, staples). It is also suitable for
working soft wall tiles, as well as for dry sanding and scraping
of small surfaces. It is especially suitable for working close to
edges and for flush cutting. Operate the power tool exclusive-
ly with Bosch accessories.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Battery unlocking button
2 Battery pack
3 Button for charge-control indicator
4 Battery charge-control indicator
5 Thumbwheel for orbit frequency preselection
6 Venting slots
7 On/Off switch
8 Tool holder
9 Handle (insulated gripping surface)
10 Plunge saw blade*
11 Clamping bolt with spring washer
12 Allen key
13 Adapter for tool holder
14 Sanding plate*
15 Sanding sheet*
16 Felt ring of the dust extraction*
17 Retaining clip of the dust extraction*
18 Vacuum connection*
19 Dust extraction*
20 Vacuum hose*
21 Extraction adapter*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Cordless Multi-Cutter
Article number
Rated voltage
No-load speed n
0
Oscillation angle, left/right
Weight according to
EPTA-Procedure 01/2003
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 84 dB(A); Sound power level 95 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Bosch Power Tools
Vibration total values a
determined according to EN 60745:
Sanding: a
Cutting with plunge cut saw blade: a
K=1.5 m/s
Cutting with segmental saw blade: a
K=1.8 m/s
Scraping: a
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Senior Vice President
Engineering
GOP 10,8 V-LI
Robert Bosch GmbH, Power Tools Division
3 601 H58 0..
D-70745 Leinfelden-Echterdingen
V= 10.8
Leinfelden, 05.12.2012
-1
min 5000 –20000
Assembly
° 1.4
Battery Charging
kg 1.0
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The Lithium-Ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
(triax vector sum) and uncertainty K
h
2 2
=2.6 m/s , K=1.5 m/s
h
=13.1 m/s
h
2
=12.2 m/s
h
2
2 2
=17.3 m/s , K=1.6 m/s .
h
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
1 609 92A 009 | (7.1.13)
English | 15
2
,
2
,