Mitsubishi Electric FDT125VNVF Technical Manual page 93

Model
Item
Power source
Operation data
Nominal capacity kW
Power consumption kW
Running current
Power factor %
Inrush current
Sound Pressure Level dB(A) Hi : 47 Me : 40 Lo : 27 (C) / Hi : 48 Me : 40 Lo : 33 (H)
Exterior dimensions
mm
Height x Width x Depth
Exterior appearance
(Munsell color)
Net weight kg
Refrigerant equipment
Compressor type & Q'ty
Starting method
Refrigerant oil
Heat exchanger
Refrigerant control
Air handling equipment
Fan type & Q'ty
Motor <Starting method>
Air flow (Standard) CMM Hi : 13.5 Me : 11 Lo : 8 (C) / Hi : 16.5 Me : 14.5 Lo : 10.5 (H)
External static pressure Pa
Outdoor air intake
Air filter, Q'ty
Shock & vibration absorber
Insulation (noise & heat)
Electric heater
Remote controller
Room temperature control
Safety equipment
Installation data
mm
Refrigerant piping size
Connecting method
Refrigerant line (one way) length
Vertical height difference between
outdoor unit and indoor unit
Refrigerant Quantity
Drain pump
Drain
Insulation for piping
IP code
Standard Accessories
Notes (1) The data are measured at the following conditions.
Item Indoor air temperature
Operation
Cooling 27˚C
Heating
(2) This packaged air-conditioner is manufactured and tested in conformity with the ISO.
(3) Sound pressure level indicates the value in an anechoic chamber. During operation these value are somewhat higher due to
ambient temperature.
(4) The operation data indicates when the air-conditioner is operated at 400V50Hz or 380V60Hz.
(5) Indoor unit specifications for one unit. Capacity and operation data is three indoor units are combined and run together.
(6) Branching pipe set "DIS-TA1"×1(option). ① : Pipe of O/U~Branch, ② : Pipe of Branch~I/U
Indoor unit SRK50ZJX-S1 (3 units)
Cooling
14.0 [ 5.0 (Min.)~14.5 (Max.)]
4.53
A 6.7 / 7.0
A
309 × 890 × 220
Fine snow
(8.0Y9.3/0.1) near equivalent
Louver fins & inner grooved tubing
Tangential fan × 1
W 27 < Direct line start >
Not possible
Polypropylene net × 1 (washable) × 2
Polyurethane form
W
Thermostat by electronics
Internal thermostat for fan motor
Frost protection thermostat
Liquid line : I/Uφ6.35 (1/4") ②φ9.52 (3/8") × 0.8 ①φ9.52 (3/8") × 0.8
: I/Uφ12.7 (1/2") ②φ12.7 (1/2") × 0.8 ①φ15.88 (5/8") × 1.0 O/Uφ15.88 (5/8")
Gas line
Flare piping
Max.30m (Outdoor unit is higher)
Max.15m (Outdoor unit is lower)
R410A 3.8kg (Pre-charged up to the piping length of 30m) Outdoor unit
Hose Connectable with VP16
IPXO
Mounting kit, Drain hose
Outdoor air temperature
DB WB DB
19˚C 35˚C
20˚C 7˚C
SRK140VSTZJX
98
5 < Max.running current 15 >
15
—
—
—
—
0
—
—
RC-E5 (option) & SC-BIKN-E (Interface kit, option)
Max.50m
—
Necessary (both Liquid & Gas lines)
WB
24˚C
6˚C
92
- -
'12 • PAC-T-174
Adapted to RoHS directive
Outdoor unit FDC140VS
380-415V 3N~50Hz / 380V 3N~60Hz
Heating
16.0 [ 4.0 (Min.)~16.5 (Max.)]
4.05
6.0 / 6.3
98
51
845 × 970 × 370
Stucco White
(4.2Y7.5/1.1) near equivalent
74
RMT5126MDE3 × 1
Direct line start
0.9 M-MA68
Straight fin & inner grooved tubing
Electronic expansion valve
Propeller fan × 1
86 < Direct line start >
Cooling : 75 , Heating : 73
0
—
—
Rubber sleeve (for Compressor)
—
20 (Crank case heater)
—
Internal thermostat for fan motor
Abnormal discharge temperature protection.
O/Uφ9.52 (3/8")
Flare piping
See page 155
—
Holes size φ20 × 3pcs
IPX4
Edging
PCA001Z566
b