NI PCIe-8255R Quick Start Guide The NI PCIe-8255R is an IEEE 1394a for PCI Express (PCIe) with reconfigurable I/O (RIO). This document explains how to install and configure the NI 8255R. What You Need to Get Started You need the following items to set up and use the NI 8255R: ❑...
When using this accessory with the NI 8255R, three of the digital I/O signals on the device are not accessible. Refer to the Connectors section of the NI PCIe-8255R User Manual for more information. NI PCIe-8255R User Manual...
Page 3
Do not exceed the maximum ratings for the device. Remove power from signal lines before connection to or disconnection from the device. National Instruments measurement products may be classified as either Caution Measurement Category I or II. Operate products at or below the Measurement Category level specified in the hardware specifications.
Page 4
MAINS is defined as the (hazardous live) electrical supply system to which equipment is designed to be connected for the purpose of powering the equipment. Suitably rated measuring circuits may be connected to the MAINS for measuring purposes. NI PCIe-8255R User Manual ) Categories: Measurement Category I is for measurements performed on circuits...
Remove the device from the package and inspect it for loose components or any other signs of damage. Notify National Instruments if the device appears damaged in any way. Do not install a damaged device in the computer. Store the NI 8255R in the antistatic package when not in use.
Page 6
Note Check that the bracket of the NI 8255R lines up with the hole in the back panel rail of the computer chassis. NI PCIe-8255R User Manual 3 PCIe x1 Connector 4 PCIe x16 Connector Figure 1. PC Expansion Slots Touch a metal part on the computer case to discharge any static electricity on your clothes or body before handling the NI 8255R.
Page 7
IEEE 1394a cable, an IEEE 1394a to IEEE 1394b adapter is required. Alternatively, you can use an IEEE 1394a to IEEE 1394b cable. NI PCIe-8255R FOR PATENTS: NI.COM/PATENTS 4 44-Pin D-SUB Connector 5 Camera Power ATX Connector Figure 2. NI 8255R Connectors NI PCIe-8255R User Manual...
Page 8
2 V Position Figure 3. Removing the 4-Position Power Connector from the Power Supply NI PCIe-8255R User Manual Complete this step if you are using the NI desktop power supply (part number 778794-01). If you are using a power supply other than the NI desktop power supply skip this step and proceed to step 2.
Page 9
Wrap the power supply cable around the ferrite two times, as shown in Figures 4 and 5. Figure 4. Installing a Ferrite Connector on the Power Supply Cable 14, 26, 29, 33, 36, 39, 42 12, 16, 18, 28, 32, 34 terminal 2 Ferrite NI PCIe-8255R User Manual...
After you have installed the NI 8255R and powered on your computer, Windows will recognize the device and assign resources to it. Use Measurement & Automation Explorer (MAX), the National Instruments configuration utility, to configure the IEEE 1394 camera connected to the NI 8255R for acquisition.
... IEEE 1394b, compatible with Level ), at 5 mA ), at 5 mA (shared by both ports) IEEE 1394a cameras Minimum Maximum 0.5 V 2.2 V — 0.4 V 2.4 V — 61.9 kΩ pull-up to 5V NI PCIe-8255R User Manual...
Output current Maximum pulse rate ...10 kHz (maximum load Minimum pulse generated ...100 μs Reverse polarity protection...Yes NI PCIe-8255R User Manual Input ON voltage ...3.5 V to 30 V Input OFF voltage...0 V to 2 V Maximum on-state voltage drop from V ...1.2 V at 100 mA 5 V isopower...50 mA, maximum...
Waste Electrical and Electronic Equipment (WEEE) EU Customers At the end of their life cycle, all products must be sent to a WEEE recycling center. For more information about WEEE recycling centers and National Instruments WEEE initiatives, visit NI PCIe-8255R User Manual EN 61010-1, IEC 61010-1 UL 61010-1, CAN/CSA-C22.2 No.
Where to Go for Support The National Instruments Web site is your complete resource for technical support. At troubleshooting and application development self-help resources to email and phone assistance from NI Application Engineers. A Declaration of Conformity (DoC) is our claim of compliance with the Council of the European Communities using the manufacturer’s...
Page 16
Instruments trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National Instruments products, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your CD, or ni.com/patents.