Control Guide - Panasonic SA-XR70 Operating Instructions Manual

Control guide

Main unit
Standby indicator [^]
When the unit is connected to the
AC mains supply, this indicator
lights up in standby mode and
goes out when the unit is turned
on.
Standby/on switch [8]
Press to switch the unit from on to
standby mode or vice versa.
In standby mode, the unit is still
consuming a small amount of
power.
Remote control
signal sensor
[VCR 2]
For a video camera,
etc.
[6.1CH DECODING]
For turning on the 6.1 channel decoding mode. When using this mode
the indicator lights.
[BASS SYNTHESIZER]
For turning on the bass synthesizer mode. When using this mode the
indicator lights.
[MULTI-SOURCE RE-MASTER]
For selecting a re-master mode. When using this mode the indicator lights.
[TUNE 2, 1]
For tuning the radio and selecting preset stations.
Press and hold until the frequency starts scrolling to start automatic
tuning. Tuning stops when a station is found.
Display
• The following indicators will dim when the dimmer is turned to "ON". They will go out when HQ sound mode is turned on.
[–SPEAKERS–  ,  ,
]
BI-WIRE
Speaker indicators
 :Sound is output from speakers
connected to the front A,
surround, and center terminals.
 : Sound is output only from
speakers connected to the
front B terminals.
  : Sound
is output
speakers connected to the
front A and B terminals.
: Sound is output from
BI-WIRE
speakers connected by
Bi-wiring.
[TAPE MONITOR]
Lights when the tape monitor is
on.
General display
Shows the input mode, radio
frequency, and other general
information.
18 • When the input signal is multi-channel DVD-Audio using a HDMI connection, DIGITAL INPUT may not display correctly.
[SPEAKERS, A, B,
BI-WIRE]
For selecting speakers A or B.
To use BI-WIRE, press [A]
and [B] at the same time.
Turning the speakers
automatically engages
STEREO/2CH MIX mode
(when listening
headphones, for example).
[BI-AMP]
Lights when the BI-AMP
function is activated.
SPEAKERS
A B BI-AMP
BI-WIRE
^
8
6.1CH DECODING
VCR 2
VIDEO IN L AUDIO IN R
S-VIDEO IN
[TUNED, ST,  , MONO]
Radio indicators
TUNED: A station is tuned.
ST: A stereo FM broadcast is tuned.
 : Flashes during automatic
presetting.
MONO: Lights when using the
monaural mode.
[SLEEP]
Sleep timer indicator.
from
[ , PS, PTY]
RDS
(For continental Europe and
the United Kingdom)
: Lights while RDS signals
RDS
are being received.
PS, PTY: Indicates the current
RDS display mode.
SPEAKERS TUNED ST
A B BI-WIRE
MONO SLEEP 2CH MIX MULTI REAR
TAPE MONITOR RDS
[% DIGITAL, % EX/PL Ⅱx, % PL Ⅱ ,
DTS 96/24, DTS-ES, DTS, DTS NEO:6]
Lights to indicate the source's input signal and
decoding format used.
% DIGITAL: Dolby Digital sources
off
% EX/PLⅡx: Dolby Digital Surround EX sources
the
or Dolby Pro Logic Ⅱx decoder is
being used.
through
% PLⅡ : Dolby Pro Logic Ⅱ decoder is being used.
DTS 96/24: DTS 96/24 sources
DTS-ES: DTS-ES discrete or matrix sources
DTS: DTS sources
DTS NEO:6:DTS NEO:6 matrix decoder is
being used.
[HQ SOUND
MODE]
Lights when using
HQ sound mode.
[SFC, CENTER FOCUS, 2CH MIX,
MULTI REAR]
SFC: Lights when using an SFC mode.
CENTER FOCUS: Lights when using
the
mode.
2CH MIX: Lights when playing a multi-
channel source in 2CH MIX
mode.
MULTI REAR: Lights when using the multi
rear surround mode.
[<<<MULTI CONTROL>>>]
When you press the [MULTI CONTROL]
button and enter the settings the
indicator lights.
M SFC CENTER FOCUS
L
PS PTY MULTI CONTROL LS SB RS LFE
DIGITAL
PROCESSING
kHz
MHz
[MULTI CONTROL]
Press
control, and use [INPUT
SELECTOR] to select/
enter.
[INPUT SELECTOR]
For selecting input.
Selects/Enters each setting
in Multi control.
[VOLUME]
Volume control.
MULTI CONTROL INPUT SELECTOR VOLUME
PUSH ENTER
DOWN UP
PHONES
[HDMI]
Lights when the signals
have been established
with a HDMI connection.
[–DIGITAL INPUT–, L, C, R,
S, LS, SB, RS, LFE]
Program format indicators
Show the channels contained in
center focus the digital input signal. They do
not light when input is analogue.
L: Front left channel
C: Center channel
R: Front right channel
S: If the surround channel is
monaural.
LS: Surround left channel
SB: Surround back channel
RS: Surround right channel
LFE (Low
Deep-bass effect.
[DIGITAL PROCESSING fs]
DIGITAL INPUT
Displays the frequency the unit is
C R S
processing.
[kHz, MHz]
fs
Frequency unit indicators
kHz: AM,
kHz frequency
MHz: FM
to enter Multi
[PHONES]
Headphone jack
Plug type: 6.3 mm
stereo
• Avoid listening for
prolonged periods of
time to prevent
hearing damage.
• Turn the speakers off
when using the
headphones.
Frequency Effects):
or PCM sampling