Summary of Contents for Napoleon WF 18
- Page 1 SERIAL / SÉRIE#______________________ DECORATIVE INDOOR WATERFALLS THAT PURIFY AND HUMIDIFY THE AIR WF 6/9/18 WF9ST MANUFACTURED BY / MANUFACTURE PAR RETAIN THIS MANUAL FOR FUTURE REFERENCE GARDER CE LIVRE POUR RÉFÉRENCES FUTURES N415-0128 / NOV16/06...
- Page 2 "NAPOLEON warrants its products against manufacturing defects to the original purchaser only (ie., the individual or legal entity (registered customer) whose name appears on the warranty registration card filed with NAPOLEON), provided that the purchase was made through an authorized NAPOLEON dealer and is subject to the following conditions and limitations:"...
- Page 3 indoor air quality Your new NAPOLEON waterfall will dramatically improve the indoor air quality in your home. The waterfall is a natural humidifier which helps alleviate dry skin and allergies. This is extremely beneficial in dry climates and also cold climates where forced air furnaces dry the air.
-
Page 4: Water Pumps
water Water is perhaps the most critical component in the waterfall. Dirty or contaminated water will quickly cause operational problems with your waterfall. House water must be softened and filtered if the unit is to be connected to the water supply. RO (Reverse Osmosis) water will give the best results, and require the least amount of maintenance. -
Page 5: Installation
INSTALLATION The framing dimensions are included in the framing specifications drawing. The unit is designed to be installed after drywalling. For added protection water resistant drywall (green board) or cement board are recommended in the vicinity of the fountain. The fountain is designed to be attached to the studs over the drywall along both vertical sides of the fountain using drywall screws. -
Page 6: Cleaning And Maintenance
BACKBOARD MORTAR TILES 23.625” Panels can also be made using materials such as mirror, glass, slate, marble or ceramic tile for display in your waterfall. If tiling, use waterproof cement board as a backer, available at any building centre. Cut the cement board to the size of your existing stainless steel panel. -
Page 7: Troubleshooting
TROUBLESHOOTING Problem Possible Causes Water not flowing. Pump not plugged in. Insufficient water level. Water flow control valve turned off. Sediment filter plugged. Pump is “vapour-locked”. Pump burned out. Dry spots on waterfall Improper start-up procedure. Ensure surface of waterfall is wet before starting by spraying with water or surface. -
Page 8: Ordering Replacement Parts
ORDERING REPLACEMENT PARTS Before contacting the customer service department, check the NAC web site for more extensive cleaning, maintenance, trouble- shooting and part replacement instructions at www.napoleongrills.com. Contact the factory directly for replacement parts and warranty claims. The customer service department is available between 9 AM and 5 PM (Eastern standard time) at 1-866-820-8686 or fax at 1-705-727-4282. -
Page 9: Framing Specifications
FRAMING SPECIFICATIONS Ø1.50” 24” RECOMMENDED* CHECK WITH YOUR LOCAL BUILDING AUTHORITY FOR COMPLETE FRAMING GUIDELINES. THE CHART BELOW WILL GIVE YOU THE OPENING SIZE REQUIRED FOR EACH MODEL. EACH WATERFALL IS IN- TENDED TO BE MOUNTED ON TOP OF THE DRYWALL (NOT SHOWN). THE DRYWALL BELOW THE UNIT SHOULD CONTINUE UP TO THE BOTTOM OF THE WATERFALL BASIN. - Page 10 PIPING DIAGRAM WITHOUT UV LIGHT FROM THREE WAY VALVE TO FROM WATERFALL WATERFALL DRAIN TO BASIN FROM BASIN TO WATERFALL DRAIN INSTALL THE SUPPLIED HOSE CLAMPS ON EITHER SIDE OF THE BASIN CUT THE SHORT PIECE OF BLACK TUBING TO 14” OVERFLOW PROTECTION TO DRAIN...
- Page 11 PIPING DIAGRAM WITH UV-LIGHT FROM THREE WAY VALVE TO FROM WATERFALL WATERFALL DRAIN TO BASIN FROM BASIN TO WATERFALL DRAIN INSTALLTHE SUPPLIED HOSE CLAMPS ON EITHER SIDE OF THE BASIN OVERFLOW PROTECTION TO DRAIN PURGELINE Remove components from basin and assemble as shown. The fittings required are already attached to the filter and basin. When using the optional UV light, the barbed elbow fitting on the “IN”...
-
Page 12: Parts List
WATERFALL SURFACE INSTALLATION The stainless steel panel provided with WF6, WF9, and WF18 is installed simply by sliding the top of the panel under the retaining bracket at the top of the waterfall, and pushing it high enough to slip over the bottom support brackets. The welded brackets that protrude at an angle from the waterfall housing, merely provide pressure to the panel to prevent it from bowing. -
Page 13: Parts Diagram
PARTS DIAGRAM...